Wheelchair Accessories
Results: 1086
Bottle and Stainless Steel Quick Cage
The Bottle and Stainless Steel Quick Cage is a wheelchair drink holder or cup holder designed for use by individuals who use wheelchairs, walkers or crutches. This stainless steel water bottle cage mounts to any vertical or horizontal tube, rail, or pole using an attached flexible plastic mount and a hook-and-loop strap. The unit includes a 21-ounce water bottle with the Twofish unlimited insignia.
"u" Adjustable Width Tray Slide Bracket Attaching System (Model 32798)
The "U" Adjustable Width Tray Slide Bracket Attaching System, model 32798, is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to the armrests from the front and the configuration of the bracket enables it to be attached to the underside the of the tray and wrap around standard wheelchair armrest pads and attached to the underside of the armrest (mounting hardware is not included). These brackets can be mounted inside or
"z" Tray Slide Bracket Attaching System (Model 32799)
The "Z" Tray Slide Bracket Attaching System, model 32799, is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to the armrests from the front. and the configuration of the bracket enables it to be attached to the underside of standard wheelchair armrest pads and the underside of the tray (mounting hardware is not included). A hook-and-loop strap attaching system (not included) may be used in conjunction with these brackets
10-Inch Scooter Bag (Model 70300)
The 10-inch Scooter Bag, model 70300, is a carrying bag for three-wheel scooters designed to hang from the handlebars on the tiller. This bag features a spring action hex frame opening to allow easy access to all items in the pouch. Opening the caddy requires placing the fingers in the middle of the frame and popping it open; closing the frame is achieved by pushing on the outside of the frame. Very little manual dexterity or strength is required to operate the opening. The bag is made of coated
13-Inch Armrest Bag (Model 70320)
The 13-inch Armrest Bag, model 70320, is a wheelchair side pouch designed for use on three-wheeled scooters. The caddy attaches to the arms using side release clips. This lined bag is made of coated nylon Cordura and features a spring-action hex frame opening. Opening the frame requires placing the fingers in the middle of the frame and popping it outward; closing the frame is achieved by simply pushing on the outside of the frame. Very little manual dexterity and strength are needed to operate.
13-Inch Sling Bag
The 13-inch Sling Bag, model 70040, is an underseat pocket designed to provide easy access and an unobstructed view of any items stored in this carrying bag to manual wheelchair users. The caddy is large enough to hold many daily needed items such as medicines, personals, writing instruments, paper, etc. The bag comes standard with a main compartment, pen and pencil pouch, and a small front pouch. The bag features a spring-action, hex frame opening which can be opened by placing the fingers in t
32 Inch Beasy Glider Transfer System
The 32 Inch Beasy Glider Transfer System is designed for use by individuals with mobility disabilities or spinal cord injury to use during transfers. Since there is no lifting involved, the risk of back and brachial plexus type injuries for the person being transferred are reduced and it eliminates back injuries for care givers with proper use. The Beasy Board by Beasy Trans provides users with a safe, comfortable and dignified way to transfer from bed to wheelchair, from wheelchair to commode o
3D printed wheelchair Hand Drive
The Hand Drive wheelchair attachment is a prototype that can be attached to any wheelchair and allows it to be powered in a rowing motion. It is an example of open source product design created by Boston-based Kate Reed, an avid unicyclist and street performer and her partner Nathaniel Tong, a competitive fencer and entrepreneur. The attachment was developed for use with existing wheelchair designs.
3Rd Hand Small Electronics Mount
The 3rd Hand Small Electronics Mount is an extension arm for wheelchair accessories designed for use by individuals with mobility or neurological disabilities or spinal cord injury. The standard mount comes with a three-segment support arm, a ball base for attachment to the wheelchair or other surface, and a head plate surface for holding small electronics such as a cell phone, iPod, camera, PDA, miniPC, or adaptive switches. The head plate has an AMPS-NEC compatible head plate hole pattern. Ite
4 Cup Coffee Caddy
The 4 Cup Coffee Caddy is designed for use by individuals with mobility disabilities. The plastic tray is designed to handle any size of hot or cold beverage drinks. Additionally, the device is sturdy, durable and reliable for users with grasping disabilities.
4 D Lapboard Adjustable Bracket Mount (08-3000 Series)
Lapboard adjusts vertically, laterally, front and rear. Adjustable tilt. 1/2 inch clear acrylic. Sizes: 24 by 15 inches (08-3111), 22 by 13 inches (08-3211), 20 by 11 inches (08-3311). Also available in 1/4 inch clear acrylic ($300.00). Modifications and accessories: 3/8 inch acrylic, colored acrylic, 1/4 inch ABS plastic, 1/4 inch lexan, cutouts, special widths and depths, aluminum rim, plastic rim, communication overlay.
6-Seater Picnic Table- Fits 1 Wheelchair
This product is designed for people who use wheelchairs. It is a 6-seater picnic table and has room for a wheelchair to also be seated at the table. It is made from high-pressure wood from sustainable sources – FSC Certified. Item will arrive “flatpacked” to save transport costs. Shipping cost included.
6650 Half Mask
The 6650 Half Mask is a headrest accessory designed to provide head support for forward thrusting individuals. The mask follows the contours of the forehead and cheeks to help hold the head comfortably within a headrest. A replaceable terrycloth pad lines the foam mask, and an aluminum inner core allows the headpiece to be formed to fit the face. For mounting purposes, one side of of the mask can be attached directly to headrest; the opposite side fastens with snap buckles. OPTIONS: 6650 Mount P
6917 Non-Stomp-Down-Able Heel Loops
The 6917 Non-Stomp-Down-Able Heel Loops are flexible polyethylene strap designed to provide an alternative to webbed heel straps on wheelchair footrests. An ankle strap is included for maintaining foot placement, as well as attachment screws. SIZES: Universally sized; one size fits all. COLOR: Black.
7901 Hensinger Covers
The 7901 Hensinger Covers are replacement covers for the 6810 Hensinger Head Support and the 6809 Hensinger Head Support with High Back (see separate entries). They are made of a cotton blend. SIZES: Extra small, small, medium or large. COLOR: Black or blue.
7902 Hensinger Strap
The 7902 Hensinger Strap is a replacement straps with either a snap buckle or an adjustable slide buckle designed for the 6810 Hensinger Head Support and the 6809 High Back Hensinger Head Support (see separate entries). The straps are attached to the back plate. An optional velcro closure is available. SIZES: Extra small, small, medium or large. COLOR: Black.
7903 Hensinger Quick Release Mount Plate
The 7903 Hensinger Quick Release Mount Plate is a headrest accessory for the Hensinger Head Supports (see separate entries). The plate has 2 straps that attach the unit to the back of a seating unit. The Hensinger Head Support attaches to the plate with velcro. The velcro release will allow the head to move forward with the body. For permanent mounting, 2 screws are used to insure that the front and back plate stay connected. DIMENSIONS: 12 x 4 inches. COLOR: Black.
7914 Half Mask Otto Bock Mount Plate
The 7914 Half Mask Otto Bock Mount Plate is a headrest accessory designed to mount the 6650 Half Mask (see separate entry) onto the Otto Bock headrest. The mask mounts with adhesive foam backing for breakaway release in the event of emergency impacts. COLOR: Black.
8-Inch Beverage Bag (Model 70020)
The 8-inch Beverage Bag, model 70020, is a caddy for attachment to wheelchairs designed to accommodate liquid containers, school or art supplies, and other items. The lined bag will holds 1 or 2 cans of soda or other drinks, sports bottles, and coffee mugs. Made of coated nylon, the caddy affixes to the wheelchair tubing with a 3-inch piece of adhesive Velcro strapping (included). The bag features a spring-action hex frame opening which can be opened by simply placing the fingers in the middle o
9-Inch Security Pouch (Model 70000)
The 9-inch Security Pouch, model 70000, is a wheelchair side pouch designed to be attached under the armrest to prevent theft of valuables and money. The flap-style pouch is secured with heavy webbing, and made of 400 Denier coated nylon packcloth. This lined carrying bag will accommodate a calculator, writing utensils, change purses or small wallets, etc. DIMENSIONS (WxH): 10 x 6 inches. COLOR: Royal blue, magenta, teal, grey, black, and burgundy.
Abilitations Mobile Sensory Rainbow Chair Accessory
Abilitations Mobile Sensory Rainbow Chair Accessory fits most wheelchairs to allow for sensory stimulation while on the go. Its moving parts provide challenges to assist with hand-eye coordination and visual tracking, while the textured fidgets provide sensory feedback to help calm children. Made of high-quality polycarbonate with plywood base for durability, the Mobile Sensory Rainbow also includes 3 inch nylon ropes for attaching up to 5 HangIts (sold separately) for suspending a child's favor
Ableware 700010000 Morph Wheels-Folding Wheels for Wheelchairs
Morph Wheels-Folding for Wheelchairs are designed to be foldable wheelchairs. Is intended facilitate transportation when traveling. It comes complete with rim, push rim and solid tire, and are designed to fit any chair with a standard quick release axle. Attaching Morph™ Wheels or removing them from the wheelchair is exactly the same process as with any other wheels that use quick release axles. The axle acts as a fail-safe mechanism ensuring that as long as it is through the hub of the wheel t
Ableware 703170000 Mobility Plastic No-Wire Walker Basket by Maddak
This no-wire walker basket is meant for walker users. The basket firmly attaches to the horizontal and vertical bars of the users walker. Its flexible, virtually indestructible, retractable stabilizing arms lock onto the legs of the walker and eliminate excess swinging. The front of the basket features a slot for an identification tag and the bottom of the basket has a built-in glass, can or cup holder, a smaller compartment for coins or medications and a trough for utensils, pens, straws or eye
Ableware 704170000 35" Mobility Leg Lift by Maddak
Ableware's Leg Lift is designed for people with limited lower extremity strength. It enables them to lift the foot onto a wheelchair foot rest, bed or into a car. The user can independently move their feet with the help of the leg strip.
Ableware 704171000 Mobility Leg Loop Leg Lift
Ableware's Leg Loop Leg Lift is designed to assist people with limited lower extremity strength to lift the leg and foot onto a wheelchair footrest, bed, into a car, etc. The foot loop stays open until the strap is pulled and then conforms to the shape of the foot for a secure and comfortable grip. A rigid middle section allows for easy maneuverability.
Ableware 706160000 Wheelchair Carry-All
The Wheelchair Carry-All is designed as backpack for the wheelchair. The wheelchair user or the caregiver can attached to the back of the wheelchair. A full-width pocket inside helps keep things in order.
Ableware 706201001 Mini Oxygen Tank Holder for Wheelchairs
Ableware's Mini Oxygen Tank Holder for wheelchairs holds M6 oxygen cylinders. The holder attaches to the handles and frame of the wheelchair and positions the tank so as to not interfere with the user's head or back. It features two pockets that can be used to hold either two cylinders or once cylinder and miscellaneous supplies, like tubing. It is made of heavy duty, waterproof nylon.
Ableware 706220001 Wheelchair Plastic Cup Holder by Maddak
Ableware's Wheelchair Cup Holder holds a drink securely on wheelchair frames, bed rails, and other tubular frames. The plastic cup holder is slotted on two sides to hold a cup with handles and is accessible to left or right-handed people. It can also hold a glass, can or bottle. The rugged plastic clamp has a large easy-to-tighten lever knob. It is designed for people with fine motors and grasping disabilities.
Abs Plastic Tray (Models 1719, 2121, & 2124)
Molded ABS Lapboard with an edge rim. Three sizes: 17 1/2 by 19 1/2 inches; 21 1/2 by 21 inches; and 21 1/2 by 24 inches. Attaches to wheelchair armrest with bayonet style hardware, adjustable for different wheelchair widths. Accessories: clear (PET) shield that snaps onto the tray for use with symbol charts. The shield becomes scratched with use and must be replaced when it becomes difficult to see through.
Abs Plastic Trays
ABS Plastic Trays can be used on wheelchairs and prone standers. The front edge and sides have a rim to prevent objects from falling off the tray. Models are available with or without cutouts. Tray glides available. DIMENSIONS (WxD): 20 x 20 inches with a 5 inch cutout (Child); and 24 x 20 inches with a 6 inch cutout (Adult). COLOR: Beige.
Access4U Portable Folding Ramp
The Access4U Portable Folding Ramp is a portable ramp designed for use by individuals with mobility disabilities or spinal cord injury. This ramp provides wheelchair access over one or two steps or a curb. The ramp is made of welded aluminum and folds to fit in a car trunk or van. DIMENSIONS (LxW): 2, 3, 4, 5, or 6 feet x 30 or 36 inches. Custom sizes are also available. CAPACITY: 600 pounds.
Accessory Mounting Platforms & Hardware
The Accessory Mounting Platforms and Hardware are adjustable wheelchair mounting kits for communicators. These aluminum mounting systems have a 2.5 x 8.5 inch platform and adjust through 360 degrees. Options include a flexible or pedestal mount, and flange, tube clamp, or tray clip.
Active Hands Gripping Aid
The Active Hands Gripping Aid is designed for use by individuals with grasping and upper extremity disabilities. The device works by tightening the strap in the upper section, which gently pulls the hand into a fist shape, adjusting to hold items in the palm. The wrist strap is also adjustable and the aid is padded to reduce chafing.
Active Wheelchair Platform Rocker
The Active Wheelchair Platform Rocker is a rocking attachment for a wheelchair designed for use by individuals with mobility or neurological disabilities, Alzheimer's disease, or spinal cord injury. This unit is designed to enable an individual to experience the benefits of rocking without transfering from a wheelchair. The rocker features an entry/exit rear ramp, adjustable front caster stops to center the wheelchair on the platform, and two safety wheelchair tie-down straps. The Active Platfo
Activity Lap Tray (Model 17698)
The Activity Lap Tray, model 17698, is a lapboard or lap tray designed for use by children ages 3 years and above and adults with mobility disabilities. Made of polypropylene plastic, this tray fits over the lap when the user is seated. The Activity Lap Tray consists of a firm flat tray between two side pockets that extent below the tray and act as the supports when the device in placed on the lap. On the tray, the user can write, play games, create crafts and perform other activities. The side
Activity Tray Swivels (Model 70675-0000)
The Activity Tray Swivels, model 70675-0000, is a swing away lapboard designed to be attached to the tubing on most wheelchairs. The tray is made of birchwood and has a clear non-slip finish on the top surface. The tray has a lip to keep items from rolling off. It is supplied with a flat triangular aluminum support and a screw-mounted 3/8-inch long aluminum spindle at one corner. DIMENSIONS: 13 x 17 inches.
Adalap
The ADALAP is a lap desk designed for use by individuals who use wheelchairs. The basic unit includes the base and pole with a top plate with a Velcro loop. Made from lightweight anodized aluminum alloy with stainless steel fasteners, the unit has a base that slides right under the wheelchair seat cushion. Height adjustment is accomplished with a quick-release clamp.OPTIONS: Fresh or salt water fishing rod holder; Snap Lap Desk; Lap Shopper shopping basket; lap tray; accessory mount for camera,
ADALAP Base Unit
The ADALAP Base Unit is designed to provide carrying capability for individuals with mobility or lower impairment disabilities who use a wheelchair. The ADALAP slides right under the seat cushion. The lightweight anodized aluminum base is durable and easy to use. No nuts or bolts, just sturdy, adjustable convenience. The ADALAP base won't rust so it can be used while out in the rain.
Adapt-A-Tray
The Adapt-A-Tray is a laptray designed to provide upper body positioning for people with spinal cord injury or neurological or severe physical disabilities who use wheelchairs. The system incorporates a tray with a hole-punched surface to enable attachment of brackets and padded blocks to aid in positioning of the upper extremities, equipment, communication aids, or activities. The starter kit includes one tray with holes, one overlay to create a smooth tray surface, four 45-degreec attachment b
Adapted Garden Spray
Adapted Garden Spray is designed for use by individuals with limited mobility in their lower extremities, limited strength and grasping in their upper extremities as a result of stroke, cerebral palsy, or multiple sclerosis. The adapted garden sprayer can be attached to any wheelchair (Clamp included) and has a flexible gooseneck mounted spraying wand, allowing the user to help maintain a healthy garden. Sprayer wand is adjustable from 12 to 24 inches. Spray nozzle is also adjustable so you
Adaptive Connection System
The Adaptive Connection System is a battery charger for use on batteries for electric wheelchairs. All ACS models feature field adaptability which includes: Input of 120 or 240 volt AC, 50 or 60 cycle, International Power Entry System; Output in the form of a plug-in DC cord matched to application need; and Voltage Setting which are adjustable in field to match current and future battery needs. Other features include automatic operation, temperature compensation, quiet operation, short circuit p
Add-On Tray, The
DO IT YOURSELF ENTRY --- PURPOSE: To keep crayons, drinks, and other items within reach of a wheelchair user. The add on tray shown was custom built of 3/8-ply to slide over the standard wheelchair tray. Multiple compartments allow her to keep crayon colors and other small items organized and hold drinks. TITLE: The Add-On Tray. WEB SITE: Workshop Solutions at http://www.workshopsolutions.com/COMPLETE/ad_on_tray.htm. REF: The originator, Tom Jeary, can be contacted at tlj@golden.net.
ADI Aluminum Series Back Support - Extra Tall
The ADI Aluminum Series Back Support - Extra Tall is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. ADI rides back support results in less pain due to more equally distributing forces through the pelvic base of support. ADI backrest is designed to give very low trunk support through different contours. Aluminum series back support is ergonomically designed product to provide relief from the low back strain on the wheelchair. ADI back support p
ADI Aluminum Series Back Support - Medium
The ADI Aluminum Series Back Support – Medium is designed for use by individuals with lower extremity. The ADI back support provides with mounting options to give adjustable or fixed positioning. ADI backrest is designed to give very low trunk support through different contours. Aluminum series wheelchair back provides with optional lateral supports to help client in balancing its position. Back support – medium is ergonomically designed product to provide relief from the low back strain on the
ADI Aluminum Series Back Support - Standard
The ADI Aluminum Series Back Support – Standard is designed for use by individuals with lower extremity. ADI aluminum series back support - standard is an option to get rid of inefficient, non-supportive alternatives. Aluminum series wheelchair back provides with optional lateral supports to help client in balancing its position and provides aids in preventative postural decay. Standard backrest is designed for lightweight wheelchair which provides strong components available for the active user
ADI Aluminum Series Back Support – Low
The ADI Aluminum Series Back Support – Low is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The ADI aluminum back support is designed to distribute the weight and force of the pelvic equally. ADI backrest is designed to give very low trunk support through different contours. Aluminum backrest is easily attached to the necessary height on the back posts of the wheelchair. Aluminum series wheelchair back provides with optional lateral supports
ADI Carbon Fiber Series Back Support - Low
The ADI Carbon Fiber Series Back Support – Low is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The ADI carbon fiber series back support - low is an ultra-lightweight seatback which designed especially for proper posture, eases the strain on the low back. CF series back support – low results in less pain due to equally distributing forces through the pelvic base of support. Back support – low ADI carbon series backrest is for that individual
ADI Carbon Fiber Series Back Support - Medium
The ADI Carbon Fiber Series Back Support – Medium is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The ADI carbon fiber series back support - medium results in less pain due to equally distributing forces through the pelvic base of support. ADI back support - medium is for that individual which knows the importance of seating and demands for lightest and strongest components available. Carbon fiber series back support is an ultra-lightweight
ADI Carbon Fiber Series Back Support – Standard
The ADI Carbon Fiber Series Back Support – Standard is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The ADI carbon fiber series back support - standard provides with optional mounting hardware to fit the specific needs of the clients. ADI back support is an ultra-lightweight seatback which designed especially for proper posture, eases the strain on the low back. Carbon fiber series back support results in less pain due to equally distributin
Adjustable Back
The Adjustable Back is a molded plastic backshell to fit 16, 18 or 20 inch width wheelchairs. The Back ($238) is two inches narrower than the wheelchair frame to fit between back uprights. It mounts to the wheelchair with an adjustable system which allows three inches of height adjustment and angle adjustment from upright to 15 degrees of recline. Mounting hardware ($266) is available to fit 3/4 inch, 7/8 inch, or 1 inch diameter frame tubing. It is easily removeable from the chair by retracting
Adjustable Channel Bracket Mount For Lapboard (Model 08-2000)
Lapboard with adjustable channel, mounts to arm of wheelchair with bracket. 1/4 inch clear acrylic. Sizes: 24 by 24 inches with 15 by 9 inch body cutout, 22 by 22 inches with 13 by 7 1/2 inch body cutout, 20 by 20 inches with 10 by 6 inch body cutout. Modifications and accessories: 3/8 inch acrylic, colored acrylic, 1/4 inch lexan, 1/4 inch ABS, special cutouts, special widths and depths, aluminum rim, plastic rim, communication overlay.
Adjustable Footrest
Tubular L-bar with adjustable angle footplate, heel loop and ankle strap. Small for 12 and 14 inch chairs, large for 16 and 18 inch chairs.
Adjustable Height Channel Bracket Attaching System (Models 31897A & 31901A)
The Adjustable Height Channel Bracket Attaching System is lapboard mounting hardware designed to secure trays to wheelchairs. These heavy-duty steel sliding spacers include all required mounting hardware for attaching to a tray (not included) and enable trays to slide on to the armrests from the front. The fixed braket, model 31897A, may be used with full-size and armrest-style trays and the flip-away bracket, model 31901A, is designed for use with armrest-style trays. The flip-away bracket perm
Adjustable J Hook Bracket Hardware Seating Package (Package 20Xx)
The Adjustable J Hook Bracket Hardware Seating Package, package 20XX, is seating hardware designed for use on a wheelchair. The Package includes a solid back insert including T-nuts; a solid seat insert including T-nuts; a wide, 1.5-inch offset seat to back hinge; a pair of 1- inch diameter tube two-hole J hooks; a pair of five-hole adjustable L brackets; a pair of 1-inch diameter tube six-hole J hooks; a pair of two-hole adjustable L brackets; a 1-inch diameter tube drop stop; and a 1-inch diam
Adjustable Split Solid Seat Insert (Model Ssp80Xx)
The Adjustable Split Solid Seat Insert, model SSP80XX, is a solid seat insert designed for use on wheelchairs. The solid seat insert includes HR foam, T-nuts, and an adjustable split seat, model MOD4900. DIMENSIONS: The foam is 1.5 inches thick.
Adl Lap Tray (Model Nc94114)
The ADL Lap Tray, model NC94114, is a lapboard designed to provide writing, eating, and activity space for people who use wheelchairs. The tray's surface is impregnated with melamine, making it waterproof and easy to clean. The tray also features a depressed edge to prevent objects from rolling off, rounded corners, and Velcro straps to secure the tray to the wheelchair. DIMENSIONS: 23.5 x 22 x .25 inches.
Adult Wheelchair Tray (Model 766)
The Adult Wheelchair Tray, model 766, is an adjustable lapboard designed to fit all size wheelchairs. The top is mar-resistant wood grain laminate and has rims on three side. DIMENSIONS: 23 1/2 inches wide x 21 1/2 deep x 1/2 inch thick, cut out size 14 1/2 x 8 3/4 inches, rims 1/2 inch high.
Afterburner Wheel Chair Pusher
The Afterburner Wheel Chair Pusher is a cycle attachment for the wheelchair designed to transport a person in a wheelchair without having to transfer her or him from the wheelchair, and to provide outdoor entertainment for individuals who use a wheelchair. The back portion of the Afterburner looks like a normal bicycle with a rear wheel, seat and pedals; however there is no front wheel or handle bars. The front of the device is designed to attach to the back of a wheelchair (included). The After
Agility Plus
Agility Plus is a legrest designed for use by individuals with lower extremity, mobility, or neurological disabilities or spinal cord injury. This articulating, swing-away legrest come in a choice of mechanical elevation or independent power elevation and is springloaded, removable, and compact.
Air Free Linville Wheelchair / Scooter Tire
The Air Free Linville Wheelchair and Scooter Tire is a polyurethane tire designed for use as a replacement tire for wheelchairs and electric scooters. This airless tire has a saw tooth tread pattern which is non-marking but can traverse severe terrain. The tire fits any manufacturer's model requiring a 410/350-4 type tire on a split rim hub. Its PSI equivalency rating is 50 pounds per square inch. DIMENSIONS: 10.5 inches in diameter x 3 inches wide. WARRANTY: Lifetime warranty against structural
Air Free Pyramid Tire, The
The Air Free Pyramid Tire is a replacement wheelchair tire designed for use by wheelchair users. This lightweight tire is designed to be used on low profile rims. This tire has a smooth, non-marking tread pattern. DIMENSIONS: 24 x 1 inches. COLOR: Available in a variety of colors.
Airfree 24 & Airfree 20
Airfree tubes for pneumatic wheelchair tires. Endurothane II pneumatic tube construction for use with conventional pneumatic rubber wheelchair tires. AIRFREE 24 has flex lock feature to snugly fit the rim seat securing spoke nipples. AIRFREE 20 has elliptical flex support for power wheelchairs. Lifetime guarantee against flats, blowouts and pressure loss. Can improve maneuverability and reduces tire wear. AF241375 fits most major brands; 24 by 1 3/8 inches. AF24125 fits most 24 by 1 1/4 inch tir
Airman Compact Air Pump
The Airman Compact Air Pump is a powered ball and tire pump designed for use to inflate wheelchair tires. This compact high-pressure air compressor quickly inflates pneumatic wheelchair tires and can be used to inflate sports balls. The unit has a built-in pressure gauge and comes with a ball adapter, balloon adapter, and owner's manual. POWER: Uses 12-volt car cigarette lighter adapter (included). DIMENSIONS: Adapter cable is 3.4 meters.
Alert Light
The Alert Light is a safety flag designed for use with manual wheelchairs, power wheelchairs or scooters. It is intended to improve the visibility of the wheelchair or scooter during the day or night. The Alert Light consists of a pennant-shaped flag has a folding shaft that enables the flag to fold below the user's head when entering and exiting vehicles or when not in use. The upper portion of the shaft has a light emitting diode (LED) light that can be set as an orange glow or a flashing str
Alimed Aerocell Ii Pressure Relieving Wheelchair Cushions
The Alimed Aerocell II is a wheelchair cushion cover designed for individuals at risk of developing pressure sores. The cushion distributes pressure for even positioning for a more relaxed and comfortable sitting experience. The device is made out of black stretch nylon and its cover is washable. DIMENSIONS: Standard size is 18 inches length x 20 inches width x 4 inches depth. CAPACITY: 440 pound capacity. WEIGHT: 3.5 pounds. COLOR: Black. WARRANTY/GUARANTEE: As stated by the manufacturer.
Alimed E-Z Release Seat Belt With Alarm
The AliMed E-Z Release Seat Belt with Alarm is a wandering patient system designed for use by individuals with Alzheimer's disease or other cognitive disabilities who are at risk for falls in homes or hospitals. This seatbelt is equipped with a standard sensor unit (included) and a hook and loop fastening buckle that, once disengaged, alerts a caregiver or hospital staff that a person is about to wander or risks a fall. The sensor alarm can be attached to regular chairs, geri chairs, wheelchair
Alimed Inflatable Lap Buddy (Model 77338)
The AliMed Inflatable Lap Buddy, model 77338, is a wheelchair lap board, positioning pad and wandering patient system designed to prevent wheelchair users with Alzheimer's disease or cognitive disabilities and balance or lower extremity disabilities from rising without assistance. It provides upper body support and posture assistance as well as a comfortable forearm and wrist/hand rest. The Inflatable Lap Buddy can support light activity, such as reading. It inflates quickly with a hand inflator
Aluminum Series Back Support
The Aluminum Series Back Support is a wheelchair back support designed for use by individuals with mobility disabilities or spinal cord injury. This contoured support is available for chairs from 10 through 20 inches in width. It is available with stationary or removeable mounting and adjustable positioning. It clamps to 0.6 through 1 inch tubing, round or oval, with no spacers required. The unit is compatible with 2-Point Pro and Quick Release mounting systems. SIZES: Low, medium, standard, tal
Amerityre Low Speed Foam Tires
Amerityre Low Speed Foam Tires, also called Flatfree tires, are foam core tires designed for use on wheelchairs. These tires have a polyurethane foam core and can never go flat. Because the density of foam is maintained at a high level, these tires exhibit low rolling resistance which means less effort is required to make them roll. Materials are ultraviolet (UV) and ozone resistant. SIZES: More than 75 sizes are available. COLOR: Black, grey, green, blue, or yellow.
Amputee Attachment Kits
Kit converts any Colson fixed back wheelchair to an amputee model. Rear wheels are moved back 1 1/2 inches to accommodate loss of body weight in front of chair. Kit is shipped with one pair of toggle brakes designed to work with the repositioned 24 inch wheels. 5/8, 7/16, or 1/2 inch axles should be specified.
Amputee Board For Below-Knee Amputees.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Padded extension to one side of a wheelchair seat to allow the stump of an above-knee amputee to be elevated and remain in extension. Instructions for building a board to fit between the wheelchair and its cushion with retractable shelves that can accommodate either a left or right amputee; and a foam pad with strips of velfoam which attaches to pieces of velcro on the shelf. Includes list of materials, drawings and photographs. SKILLS REQUIRED: Woodwo
Amyseat Modular Power Seating System
The AmySEAT Modular Power Seating System is a powered reclining and/or tilt-in-space seating system designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The seating system comes with either Power Tilt, Power Recline, or both. Power Recline comes with mechanical ISR (Integrated Shear Reduction). CONTROLS: Single actuator seat controller with dual toggle switch. SEAT (LxW): 14 to 24 x 14 to 24 inches in 1-inch increments. All systems include adjustab
Angled Footrest.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Padded, angled footrest for use when seated in an armchair. Lists materials (wood) needed and provides instructions for constructing a footstool angled to support the feet in comfort. The height and angle of the stool can be determined by experimenting with cushions. Should be well padded, particularly under the heels. SKILLS REQUIRED: Woodworking. AUTHOR: Caston, D TITLE: Easy to Make Aids for Elderly People REF: London, England: Souvenir Press: p 84-
Ankle/foot Straps
Pair of velcro straps with mounting hardware and D-ring closures. Can be mounted to padded footboards or existing wheelchair footrests, positioned to strap ankle or forefoot.
Anna-Dote
Anna-Dote is a back support cushion and solid back insert designed to aid individuals who use wheelchairs, or straight-back/recliner geriatric chairs to sit upright, allowing for the reduction in stress, discomfort and fatigue that can accompany a slouched to the side position. This positioning supportive aid fits over the backrest of either a wheelchair or a geriatric chair and provides patients with an extended backrest to keep them upright and prevent falling or sliding to the side of the cha
Anti-Thrust Solid Seat Insert (Model Ssp40Xx)
The Anti-Thrust Solid Seat Insert, model SSP40XX, is a solid seat insert designed for use on wheelchairs. The solid seat insert includes HR foam, T-nuts, and an anti-thrust seat, model MOD4400. DIMENSIONS: The foam is 1.5-inches thick.
Anti-Tipping Bracket (Models 85F & 85R)
The Anti-Tipping Bracket is an anti-tipping lever designed for use on wheelchairs. The device consists of a pair of curved tubes, each with a small roller wheel, that attach to the wheelchair frame. Model 85F extends beyond the front caster to prevent forward tipping of the wheelchair. Model 85R extends from the back of the chair to prevent rear tipping.
Arm Tote (Models Ez0123 & Ez0124)
The Arm Tote is a wheelchair or scooter side pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made of nylon, this pack attaches to the armrest of a wheelchair or scooter with the two adjustable straps with plastic fasteners. An inner pocket can be accessed by opening a full-length zipper. There are two (model EZ0124) or three (model EZ0123) pockets on the outside. SIZES: Large (model EZ0123) and small (model EZ0124). DIMENSIONS (HxLxW): 2 x 14 x 10.5 inches
Arm Tray Lateral Stabilizer (Models 706140, 706141, & 706142)
The Arm Tray Lateral Stabilizer is a combination lateral trunk support and arm trough designed for use by individuals who use wheelchairs. This foam-padded stabilizer fits wheechairs with full-length arms and reduces lateral leaning while providing improved arm positioning. Model 706140 has a washable polyester cover, model 706141 has a washable synthetic sheepskin cover, and model 706142 has a spray-and-wipe clean nylon cover.
Arm Tray With Arm Tray Pillow (Model A74610)
The Arm Tray with Arm Tray Pillow is an arm trough designed to provide arm support for people with upper extremity disabilities who also use wheelchairs. This tray features a comfortable, polyester fiber filled pillow containing extra filling underneath the hand for elevation to help reduce edema. The forarm portion of the pillow cups the arm, padding the sides and base of the tray. It includes all straps to securely position the pillow in the tray and the arm on the pillow. The pillow is machin
Arm Tray With Straps (Model A7461)
The Arm Tray with Straps, model A7461, is a plastic arm trough designed to provide arm support for people with upper extremity disabilities who also use wheelchairs. The tray is equipped with three Velcro straps to secure the device to the wheelchair and Kushionflex pad to buffer any potential area of irritation. The tray can be secured on chairs with standard arms using three straps and on chairs with desk-length arms secured by only two straps. DIMENSIONS: The straps are one inch wide and the
Arm Tray.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Provides support, elevation, or both for the forearm and hand of an individual setting in a wheelchair. Directions and materials given for 2 sizes of arm tray. diagram. similar to commercially available product. Attaches to wheelchair armrest. SKILLS REQUIRED: Woodworking, plastics. AUTHOR: Fahland, B. TITLE: Wheelchair Selection: More Than Choosing a Chair With Wheels. REF:Book: Sister Kenny Institute, Minneapolis, MN; p 47- 48. 1976.
Arm Trough (Model 07-D)
Arm trough has molded plastic shell with energy absorbing foam pad covered with molded naugahyde skin. Provides full support from elbow to hand. Overall length is 18 1/2 inches; bed length is 15 1/2 inches, depth, 1 1/4 inches; elbow stop is 3 1/2 inches long and 2 1/2 inches high; inside width is 4 inches, flares at front to 6 1/2 inches.
Arm Trough (Model 09-2000)
The Arm Trough, model 09-2000, is an arm trough designed to support and position the arm for use with seating systems and wheelchairs by individuals with mobility and neuromuscular disabilities. For use with on the left and right arm, the Arm Trough is made of .25-inch Kydex with 1-inch nylon webbing straps with faux sheepskin covers. Hook and loop straps or buckle closure are standard. SIZES: Small/pediatric, medium/adolescent and large/adult. DIMENSIONS (LxW): 12 x 4.5 (small); 17 x 5 (medium)
Arm Trough (Model 09-4000)
The Arm Trough, model 09-4000, is an arm trough designed to support and position the arm for use with seating systems and wheelchairs by individuals with mobility and neuromuscular disabilities. The trough is designed with a curved shape to help protect and keep the forearm in place and features a soft durable Lycra neoprene liner to help reduce skin irritation. Other features include an elbow block to keep the arm stationary in a tilted or reclined position, and a padded wrist strap with Velcro
Arm-A-Rest
The Arm-a-Rest is a carrying caddy designed for attachment to all wheelchairs with arm and/or back support. The pouches are fabricated of water repellant and stain resistant crushed velvet and drape over either the armrest or the back of the chair. The armrest version has a padded section which rests on top of the armrest pad; the bag storage version has a padded section which provides back support. The pouches attach with hook and loop strips. OPTIONS: A cushioned arm and storage pouch; a cushi
Armchair Fitness Aerobics
Armchair Fitness is an exercise videotape designed for use by seniors or individuals with mobility disabilities. The program includes three graduated 20-minute workouts of seated stretching and strengthening exercises set to music.
Armrest Cushions (Models 436A4 & 436A5 Series) & Channel Armrest (Models 436A2 & 436A3)
The Armrest Cushions, models 436A4 and 436A4 series ($63 to $21), and the Channel Armrest, models 436A2 and 436A3 ($35 to $32), consist of steel reinforced armrests, injection molded with self skinning foam. Straight armrests, and desk or full length sizes are molded to cradle the arm for support. The Channel interchangeable armrest is molded to cradle the elbow and arm with several different hand pads available. The Cushions can be mounted directly to standard wheelchair arms or used with the 4
Armrest Fixed Bracket (Model 31897)
The Armrest Fixed Bracket, model 31897, is an add-on armrest bracket designed to allow any tray to be attached to wheelchairs. The 1/8-inch steel bracket has a baked epoxy finish. INSTALLATION: The bracket is attached to the underside of the tray using the included hardware; the tray is then installed on a wheelchair by sliding the bracket over any standard or padded armrest. WARRANTY: The manufacturer warrants this product against defects in workmanship and materials for 90 days from the date o
Armrest Flip-Away Bracket (Model 31901)
The Armrest Flip-Away Bracket, Model 31901, is a bracket designed to connect trays to wheelchairs and allow the trays to be flipped up 90 degrees. The bracket is 1/8-inch steel with a baked epoxy finish and includes an aluminum flip bar and spacers. INSTALLATION: The bracket is attached to the bottom of the tray with the included hardware; the bracket slides over any standard or padded armrest. WARRANTY: The manufacturer warrants this product against defects in workmanship and materials for 90 d
Armrest Inhibition Cradle
The Armrest Inhibition Cradle is an ABS plastic contoured arm trough with velcro-in vinyl pad. The trough has forearm and upper arm sections. The adjustable mounting hardware clamps to standard 7/8 inch tubing armrests.
Armrest Modification For Support Of Paretic Or Paralyzed Upper Extremity.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Modification of a wheelchair armrest to provide a surface for positioning or exercising a paralyzed or partially paralyzed arm. Describes an armrest made of wood padded with foam-backed carpet, which is attached to the arm of a wheelchair with a hose clamp, and which has a Velcro safety strap to hold the arm in place. Includes instructions, diagram and photographs. SKILLS REQUIRED: Woodworking. Assembly. AUTHOR: Pifer, R G TITLE: Armrest Modification f
Armrest Mounting Bracket (Model 3395)
Used in ocnjunction with a standard hand-control clamp for mounting a Model 3185 joystick for hand operation. Consists of a 1/2 inch diamter stainless steel mounting rod fitted to a 3/4 inch diamter mounting shaft to permit a wide range of joystick positioning.
Armtrough Alternative
The Armtrough Alternative is an add-on armrest designed for use by individuals with upper extremity, severe physical, or neurological disabilities who use wheelchairs. This armrest cradles the arm in a range of positions and is padded for comfort. This adjustable unit is built with lateral for trunk support and to block elbow medially and includes an elbow stop to keep the elbow secure. The unit also comes with a hand block for hand and finger positioning.
Arrow Microcomputer Control (Mcc) Mk Ii
The Arrow Microcomputer Control (MCC) MK II is a motor and accessory control system designed for Invacare Arrow and Arrow XT series wheelchairs. The standard system includes a joystick with indoor/outdoor, high/low, on/off, and horn toggle switches; and battery level display, mode and level indicators. Other features include a standby mode; emergency stop switch input; and proportional head control compatibility. Adjustable performance features include indoor/outdoor performance, maximum speeds,
Articulated Mounting Arm Kit
The Articulated Mounting Arm Kit is a two section articulated arm designed to be used in conjunction with QuadStick Sip/puff mouse control products. It has a Super Clamp with quick release, and a ball and socket RAM Mount adapter. A user can clamp this mount to tables and tubular surfaces such as wheelchairs. The ball and socket adapter allows adjustment of the QuadStick’s position at the end of the arm.
Asl 12 Volt Sealed Lead Acid Battery And Charger (Model Asl515)
The ASL 12 Volt Sealed Lead Acid Battery and Charger, model ASL515, is a battery for wheelchair accessories, switches, or sensors, designed for use by individuals with mobility disabilities. This transportable battery provides a 12-volt power source for accessories or 12-volt direct current (DC) switches/sensors. The battery is lightweight and can fit into a small wheelchair pouch. It provides 1.2 amp hours of power. The battery is sealed and comes with a charger. DIMENSIONS (HxLxW): 2 x 4 x 2 i
Asl Adjustable Proximity Sensor With Mono Port (Model Asl208_M)
The ASL Adjustable Proximity Sensor with mono port, model ASL208_M, is a sensor switch designed for use by individuals with upper extremity disabilities, neurological disabilities, or severe physical disabilities. This "no touch" proximity switch has an adjustable "void space" range, which allows the switch to function when mounted under a surface up to a half-inch thick, thus allowing the proximity field to begin above the voided area (for example, the surface of a tray). This switch works with
Asl Fiber Optic Sensor With Mono Port (Model Asl202-M)
The ASL Fiber Optic Sensor with Mono Port, model ASL202_M, is a sensor switch designed for use by individuals with mobility, communication, or severe physical disabilities. This single function switch has an adjustable activation range from touch to 2.5 inches, with a round target area. This fiber optic switch can be programmed for either normally open (NO) or normally closed (NC) operation. In the NO mode, switch activation occurs when an object is detected in the adjusted range. In the NC mode
Asl Laptop Power Converter (Asl509)
The ASL Laptop Power Converter, model ASL509, is a wheelchair battery adaptor designed for use by individuals with mobility disabilities. This adaptor enables the user to run a laptop computer using a powered wheelchair battery. The power source converter connects to the powerchair batteries and converts 24 volts to the voltage required to power a laptop computer. To operate, this converter requires the computer's automotive power adaptor and a model ASL804 power source adaptor.
Asl Proximity Sensor With Mono Port (Model Asl204-M)
The ASL Proximity Sensor with Mono Port, model ASL204-M, is a sensor switch designed for use by individuals with upper extremity disabilities. This "no touch" switch can be used with ASL proportional driver controls with power wheelchairs or for non driving purposes such as computer control. This single function switch has an activation range of touch to half inch. Activation occurs when it senses a hand or another part of the body in the activation area. This switch is intended to be used throu
At Ease Adjustable Foot Support (Model Fs18Aj)
At Ease Adjustable Foot Support, model FS18AJ, is a foot support designed to promote proper posture, reduce fatigue and back strain and relieve stress on the legs, back and neck. The tilting support platform allows the user to vary the leg position and aids in circulation in the legs and feet. This foot support adjusts in height and angle and is ideal for workstations with multiple users. The platform is made of molded and texturized plastic and the frame is made of durable chrome tube. The supp
At Ease Standard Foot Support And High Foot Support (Models F300 & F600)
The At Ease Standard Foot Support and High Foot Support, models F300 and F600, are foot supports ergonimcally designed to support proper posture, reduce fatigue and back strain and relieve stress on legs, back and neck. The tilting support platforms allow the user to vary leg positions and aids in circulation in legs and feet. Both models have a durable wooden platform laminated with a non-skid vinyl surface; a lightweight chrome frame; and rubber feet to hold it in place. DIMENSIONS: Models F30
Attaching Hardware Kit (Model 31096H)
The Attaching Hardware Kit, model 31096H, is lapboard mounting hardware designed to attach lapboards and trays to wheelchairs. This kit includes four truss head phillips screws, four mushroom head T-nuts, and four plain T-nuts and provides sufficient hardware to attach two clamps or brackets to a tray (tray not included).
Attaching Hardware Kit (Model 33066)
The Attaching Hardware Kit, model 33066, is lapboard mounting hardware designed to attach lapboards and trays to wheelchairs. This kit includes four 10-24 x 3/8 inch flat socket head screws, four 10-24 x 0.5 inch flat socket head screws, and four plain T-nuts and provides sufficient hardware to attach two clamps or brackets to a tray (tray not included). COLOR: The screws are black.
Attendant Wheelchair Control (Model 3320)
Used to expand the capability of a Multimode Interface by providing remote, attendant operation of the wheelchair. Uses a proportional joystick for precise control of wheelchair speed and direction. a toggle switch (with indicator light) is provided to ruen the attendant wheelchair control on and off. When the control is turned on, the Multimode Interface is automatically reset to standby status to prevent the wheelchair user from attempting to operate the wheelchair during attendant oepration.
Auto Style Hip Belt (Model Ee 3D/103-6000)
Wheelchair seat belt, nylon webbing and auto style push button buckle. Has a pair of iliac crest relief pads so the the belt may be cinched tightly without causing pressure on the bony prominences. Should be mounted at a 45í angle to the seat.
Automatic Wheelchair Anti-Rollback Device
The Automatic Wheelchair Anti-Rollback Device is a supplemental wheel locking device designed for use by individuals with mobility disabilities. As the individual rises from the chair, a pair of brake arms grab the tires to prevent the chair from rolling backwards. Once the user is seated, the device releases and goes into "stand-by" mode and the wheelchair returns to standard operation. Activated by spring tension, a padded lever beneath the wheelchair seat is depressed when the user is seated.
Automatic Wheelchair Anti-Rollback Device
The Automatic Wheelchair Anti-Rollback Device is a supplemental wheel locking device designed for use by individuals with mobility disabilities. As the individual rises from the chair, a pair of brake arms grab the tires to prevent the chair from rolling backwards. Once the user is seated, the device releases and goes into "stand-by" mode and the wheelchair returns to standard operation. Activated by spring tension, a padded lever beneath the wheelchair seat is depressed when the user is seated.
Awesome Grip
Awesome Grips are handrim covers designed for use by people who use wheelchairs. These removable, changeable covers fit the push wheels of manual wheelchairs and have a closed cell foam base with a fabric or leather cover. The covers do not slip on the rims, are designed not to slip in the hands, and provide a larger, softer gripping surface. The covers are available in leather, imitation leather, fabric, velveteen, and plush fabric. COLORS: Leather and velveteen covers are available in red or b
Axion Rotary Interface For Wheelchair Headrests
The Axion Rotary Interface™ for Wheelchair Headrests is a headrest accessory designed for use by individuals with severe physical or neurological disabilities or spinal cord injury. This device permits wheelchair headrests to rotate, and it attaches to most existing wheelchair headrests and hardware. This unit is quiet, free-running, and it does not require lubrication. The range of rotation can be limited or stopped.
Axle Bracket
The Axle Bracket is a rear wheel position adapter for wheelchairs designed to provide additional height adjustability for the axles on a wheelchair without drilling the frame. Two 9 mm aluminum plate brackets bolt into the existing adjusting holes on a wheelchair frame. The wheel axle can be bolted to the adjusting slot on the bracket. PROTOTYPE DEVELOPMENT: Designed by Andre Paquette for a user who could not adjust the seat height on the wheelchair low enough. Modifications by the wheelchair ma
Backpack Retriever
The Backpack Retriever is a wheelchair back pouch access aid designed for use by individuals who use wheelchairs. This device brings a backpack from behind the chair to within reach of the user with a click of a button. Without increasing the overall dimensions of the wheelchair, the unit is aesthetically designed to fit most power wheelchairs and does not interfere with accessibility through doorways. The patented linkage mechanism enables the device to be used in close or confined areas such a
Band-It
Band It is an ankle strap designed for use by individuals with lower extremity and neurological disabilities who use wheelchairs. This positioning device is designed to be secured around the ankle, with the body of the device extending over the top of the userÆs shoe and orthosis. The device has a dynamic component that allows some movement at the ankle to prevent joint stiffening and full body tonal reaction, and reduce buttock shear. The device has a side-squeeze closure that can withstand 250
Basket For Wheelchair
CUSTOM ADAPTATION PURPOSE: To enable individuals with mobility disabilities to shop and carry items. Designed for use on a variety of wheelchairs, the adaptation consists of a commercially-available plastic-coated wire basket that fits against the back of the chair between the rear wheels. The basket is secured to the chair with octopus straps to enable removal when not in use but keeping the basket from swinging when on the chair. TITLE: In the Basket. JOURNAL: TAD Journal. REF: Vol. 21 no. 2,
Battery Booster, The
Boost charger for 24 volt electric wheelchairs. Charges chairs from 12 volt supply; cigarette lighter adapter, automotive battery chargers, etc. Can also be used to operate 12 volt accessories from wheelchair batteries. Can fully charge batteries in 3 to 4 hours; however, designed to give quick "boost" charge while driving or sitting. Installs on wheelchair. Some vehicle adaptation may be necessary. Size 5 by 2.5 by 1.5 inches; weight less than 1 pound.
Beach Econo Kit
The Beach Econo Kit is a kit for converting a wheelchair or stroller into an all-terrain wheelchair or stroller designed for use by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury. The kit consists of four balloon wheels from Roleez Wheels, Inc. (see separate entry), two pre-drilled anodized axles, u-bolts, and wheel clips. To mount, the rear wheels are popped off, the axle tubes are slid across the frame and bolted on, and the balloon wheels are slid
Bean Bag Dinner Tray
The Bean Bag Dinner Tray is a lap tray designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Designed to rest directly on the user's lap, this plastic tray attaches to a bean bag with a hook and loop strap. The removable bean bag provides a form fitting and comfortable support on the user's lap. The tray's raised edges are intended to stop items such as cups and plates from accidentally sliding off the tray. DIMENSIONS (WxD): 16 x 12 inches. COLOR:
Beasy II Transfer System
The Beasy II Transfer System is designed for use by individuals with mobility disabilities or spinal cord injury to use during transfer. The transfer system is desinged for use in smaller areas, especially during bathroom transfers, or for boosting patients in bed. It may also be used for independent transfers with professional approval.
Better Board Slant Boards
The Better Board Slant Board is a bookholder and table top writing desk designed for use by individuals who use wheelchairs or who have upper extremity. It is made of durable corrugated plastic, it has attached plastic clamps that hold paper well and includes non-slip feet to help it stay in place while in use. It has a 20-degree angle and can be used for reading, writing and copying. When not in use, this board folds to a thickness of 0.75 inch for stacking and storing. SIZES: Small and large.
Bi-Fold Sensor Pad For Chair And Bed
The Bi-Fold Sensor Pad is a discrete sensor that alerts a caregiver when their patient has fallen from their bed or chair. This dual purpose sensor pad can be folded. In it’s folded format the pad measures 15 inches wide x 15 inches long and can be placed on the wheelchair either above or below the seat cushion. In the unfolded position it measures 15 inches wide x 30 inches long and can be placed under or over the mattress. The pad is liquid resistant.
Bi-Level Footrest Extender (Series 7033)
The Bi-Level Footrest Extender is designed for use by people who use wheelchairs and who have leg-length discrepancy. The extenders can be selected in a right-left or left-right combination and they feature a vertical centerboard which prevents the feet from crossing over and a padded legrest to prevent the feet from slipping off the footrests. DIMENSIONS: The extenders are available in a choice of 16 or 18 inches wide and with 1- and two-inch pads, 1- and 3-inch pads, 1- and 4-inch pads, 2- and
Bib Kit (Model 3390)
Used for mounting a Model 3185 joystick for chin operation. The bib uses velcro straps to secure the bib around the neck and rib cage, and incorporates adjustable mounting harware to permit a wide range of joystick positioning.
Big Ben Shopper
Wheelchair back pouch attaches to handgrips of wheelchair with straps. Room for complete change of clothes, lap robe, or other large items. 16 by 17 inches. Black or saddle. Vinyl.
Binocular Clamp
The Binocular Clamp is an extension arm for accessories designed to enable a persons to use a pair of binoculars without having to support the weight of them. The device consists of a 360-degree swiveling clamp fixed to the end of a 13 mm diameter stainless steel rod. The rod mounts onto the fitting of a wheelchair. Binoculars are attached to the device with an off- the-shelf Kaiser binocular fitting. PROTOTYPE DEVELOPMENT: Designed by Colin Knauf for a user with weak arms who can raise the bino
Biosoft Palm Guard Gloves
The Biosoft Palm Guard Gloves are push gloves designed to protect the wearer's hands while propelling a wheelchair. These gloves feature an elastomer palm grip to absorb shock, vibration, and pressure. These pull-on fingerless gloves have an open-weave mesh back with adjustable Velcro closure. SIZES: Small, medium, large, and extra large.
Birdie Buddy
---- PROTOTYPE --------- PURPOSE: To create a prototype of a wheelchair mount for a camera and binoculars for an avid photographer and birdwatcher with quadriplegia. The Birdie Buddy clamps securely to a bar on the wheelchair base frame, holds a camera or binoculars at eye level, and folds down along the side of the wheelchair when not in use. This device supports the weight of the camera or binoculars, convenient switching between the two pieces of equipment, and an adjustable viewing angle. T
Black Poly Spoke Guard With Alloy Hand Rim
The Black Poly Spoke Guard with Alloy Hand Rim is a spoke protector with attached handrim designed for use by people with lower extremity or mobility disabilities or spinal cord injury who use manual wheelchairs to play wheelchair rugby and other wheelchair sports. This unit is for use on the Melrose Rhino wheelchair rugby chair (see separate record). The poly spoke protector is riveted to a ring that is welded to the inside of an alloy handrim. The unit is attached to a wheel (not included) wit
Black Poly Spoke Guards With Rubber Hand Rims
The Black Poly Spoke Guards with Rubber Hand Rims are spoke protectors with attached handrims designed for use by people with lower extremity or mobility disabilities or spinal cord injury who use manual wheelchairs to play wheelchair rugby and other wheelchair sports. The poly spoke protector is riveted to a ring that is welded to the inside of a rubber handrim. The unit is attached to a wheel (not included) with 6 or 12 tabs that mount either onto the rim or close in. The spoke protectors sit
Black Texture Coated Footplates.
Footplates for Quickie wheelchairs. 90 degree/90 degreee aluminum footplates with a painted black texture surface. Replaced textured tape to provide nonslip surface.
Black Trays
The Black trays are wheelchair lap trays designed for use by individuals who use wheelchairs. These PVC trays are equipped with attached rims and are difficult to crack. SIZES: Infant, child, and adult sizes. COLOR: Black.
Blatchford Moulded Seat Inserts
Blatchford Moulded Seat Inserts are moulded seat inserts used to give support and pressure relief to those who spend a lot of time in a seated or supine position as a result of limited lower extremity mobility. The inserts are made from a high-density polyethylene that is crack-resistant and has a layer of medium density foam for comfort.
Bogen Multi Position Support Arm & Super Clamp
The Bogen Multi-position Support Arm and Super Clamp are mounting hardware for communicators and other accessories designed to be mounted to a table or wheelchair. The Support Arm has a fully articulated arm (three universal joints) with 90 degree pivotable and 360 degree rotatable ends, and an elbow that rotates 360 degrees. The adjustable, one-control handle located at the elbow joints locks all three joints firmly. The arm can be mounted permanently, or used with the Super Clamp. The Super Cl
Boss Hd Equalizer Bariatric Tilt System
The BOSS HD Equalizer Tilt System is a powered tilt-in-space system designed for use by individuals with mobility, neurological or severe physical disabilities. This tilt-in-space system is designed to be mounted on a heavy-duty power wheelchair base (not included) such as the PaceSaver BOSS 6 powered wheelchair (see separate entry). CONTROLS: Integrated programmable Shark joystick controller. A swing-away controller mount and attendant control are optional. SEAT (DxW): (18 to 26) x (22 to 30) i
Bottoms Up Bar
The Bottoms Up Bar is a transfer aid designed for people with lower extremity and mobility disabilities or spinal cord injury and lower extremity amputees. It allows a person in a wheelchair to transfer to a seated position on the ground or floor and from the floor or ground back into the wheelchair. The Bottoms Up Bar attaches to a wheelchair's frame with two collar clamps that are fastened to the front of the frame. The width of the Bottoms Up Bar is adjustable to accommodate multiple wheelcha
Bracket To Hold Power Packs For Wheelchairs
CUSTOM ADAPTATION PURPOSE: To enable a controller for a power assist for a manual wheelchair to be attached to wheelchair push handles. The power assist units are suspended under the wheelchair seat and the controllers are attached to the wheelchair push handles with the included full-circle Bakelite clamp for access by caregivers.When the clamp did not fit over the rubber handgrips, a split metal clamp was designed. The top lock was macined of aluminum and threaded for bolts. The bottom was ma
Brake Attachment
This Brake Attachment is for wheel brakes on a wheelchair. The brake applies one square inch of surface against wheel to increase the holding power of the brakes. No tools are needed to attach brake to a wheelchair.
Brake Extension (Model 86)
The Brake Extension, model 86, is a wheel lock extension lever designed for use by individuals who are unable to reach or manipulate standard wheel locks on wheelchairs. These devices attach to the existing wheel lock brake of a wheelchair and is held in place by a lock knob.
Breath Actuator (Model 3365)
A 4-direction, multiple switch actuator used to convert varying amounts of breath suction and pressure (sip and puff) into the directional commands required by the Multimode Interface for mode selction and oepration. The Model 2422 Breath Tube Kit is used to provide a means of sending these sips and puffs to the Breath Actuator.
Breath Tube Kit (Model 2422-2)
Used for supplying sip and puff directional commands to the breath actuator. The Breath Tube Kit includes a wingaway strap clamp mount for attachment to a standard 7/8 inch diameter wheelchair/power recliner back bar. The mount permits the breath tube to be pivoted away from the user by an attendant and returned to its original position without the need to readjust the flexible breath tube.
Brella Buddy
Brella Buddy is a hands free wheelchair umbrella holder which does not require attachment to a wheelchair. No heavy accessories to carry around when it is not raining. The Brella Buddy, hands free wheelchair umbrella holder will hold your umbrella for you and protect you from the rain while keeping your hands free to propel your wheelchair.
The Brella Buddy hands free wheelchair umbrella holder is designed with a two strap, adjustable system to hold it comfortably in place. There are two pockets
Buckles & Belts
Wheelchair seatbelts with 2 types of hook and loop closures, molded plastic Delrin buckle (operates by pinching both sides of buckle simultaneously), lever aircraft buckle, or push button aircraft buckle. Two piece or single continuous belts. Available sizes from 48 to 108 inches.
Burfab Communication Board
The Burfab Communication Board is a custom adaption designed for individuals with upper extremity and grasping disabilities to hold their communication board in place on a wheelchair. This is a portable communication board with a handle, covered on both sides with burfab (velcro friendly material). It is lightweight and can be carried by a child if need be to keep communication or schedules close at hand.
Buzzy
The Buzzy is an add-on power unit designed for use with a manual wheelchair. This motorized tow device provides powered mobility for shopping and recreation without requiring the user to transfer. The user wheels up to the unit, grabs the handlebar, and pushes the thumb throttle. The unit has variable speeds. The Shopping model, which is intended for use in supermarkets and other stores, has a lower top speed than the Recreation model. An on-board microprocessor allows the user to reset the top
Cam Belt With Grommets (Model Es-350)
The Cam Belt with Grommets, model ES-350, is a child belt restraint for pelvic stability. The two-piece belt is made of automotive seatbelt nylon and has a nylon buckle. The belt attaches with grommets to various therapeutic equipment and seating aids. The nuts, bolts, and washers required for installation are included. DIMENSIONS (LxW): 40 x 2 inches.
Canadian Padded Transfer Board
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Padded transfer board with a plinth which fits into the forward arm rest socket of a standard wheelchair. Transfer board made of 15 by 6 1/2 inch plywood, a base plate of iron or steel, an iron water pipe, a sheet (10 by 6 inches) of firm leather or plastic, foam padding and a slippery fabric cover. The board is used in place of either arm of the wheelchair. Includes instructions and diagrams. SKILLS REQUIRED: Woodworking. Upholstering. AUTHOR: Wightwi
Capstan Handrim
The Capstan Handrim is a wheelchair handrim designed for people with lower extremity or mobility disabilities or spinal cord injury. This aluminum alloy handrim is plastic-coated intended for users with good arm and shoulder strength but poor hand and finger grip. This handrim is fitted 8 projections at either 45 or 0 degrees (vertical). There are 3 different mounting systems for the hand rims: standard tab, close-in tab, or riv-nut. OPTIONS: 10 or 12 projections. SIZES: For 20-, 22-, 24-, 25-,
Carbon Core Wx 2.5
Carbon Core WX 2.5 is a lightweight wheelchair wheel option. It is designed to reduce linear momentum and reduce rotational inertia. The thermoplastic resin and Kevlar/carbon fibers work together to dampen road vibration. The wheelchair spokes are designed to maintain lateral stiffness and firm responsiveness, these composite spokes absorb some of the road "buzz", for greater comfort and control. There is a special thermoplastic carbon fiber composite material for the hub shell. It has strength
Carbon Core Wx2.5
The Carbon Core WX2.5 is a rear wheelchair wheel for people with mobility disabilities, spinal cord injuries and other people who use manual wheelchairs. This very lightweight wheel is has a rim of heat treated 6061 T6 aluminum with a double-walled design, 7075 T6 aluminum spoke nipples and 20 continuous carbon fiber spokes. It fits standard .5-inch axles. DIMENSIONS: Available in 24 inch or 25 inch diameter. CAPACITY: 250 pounds. WEIGHT: 2.5 pounds (24 inch) or 2.6 pounds (25 inch). COLOR: Blac
Carbon Series Back Support
The Carbon Series Back Support is a wheelchair back support designed for use by individuals with mobility disabilities or spinal cord injury. The unit consists of a carbon shell, cushion and cover. It has an active support contour of 2.5 inches. The unit is compatible with Fixed Elite, 2-Point Pro and Quick Release mounting systems. The fixed positioning unit clamps to 1-inch tubing; all other tubing sizes require spacers. The adjustable positioning unit clamps to 0.6- through 1-inch tubing, rou
Carebike
The Carebike is a cycle attachment for wheelchairs. The unit comprises an anodized aluminum platform on wheels that attaches to a 21-speed comfort bike. It is designed to offer friends, family members and caregivers the convenience of taking a bike ride while still being close at hand to assist the wheelchair user. The wheelchair fits on the platform with the Carebike attached at the rear, giving the biker complete steering, stopping, and starting control.
Cargo 16 Wheelchair Pouch
Wheelchair back pouch. Cordura nylon fabric with look of cotton duck. 1, 000 cubic inches inner space. Removable shoulder strap. Full width outer and back pockets. Zipper opening top. Strap loops on pouch slip over wheelchair push handles folds with wheelchair. Specify narrow or regular wheelchairs, 12 to 14 inches wide.
Carriers For Crutches And Tripod
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To provide a custom adapted crutches and tripod carriers for an adult with spastic paraplegia and oral dyspraxia. The crutch holder accessory available from the wheelchair manufacturer was too small for the tripod and would be difficult to import from the United States. The custom adapted design began by taking an aluminum base panel and bolting it to the anti-tip legs on the back of the chair. To make the holders for the crutches and the tripod, pla
Carry All Pouch (Model 976)
The Carry All Pouch, Model 976 is a wheelchair and walker carry-all with four accessible pockets. The pouch is secured with Velcro fasteners over the front of the arm of a wheelchair or a walker bar. DIMENSIONS: 9.5 x 1.25 x 13 inches.
Carry All Pouch For Walker (Model 1116)
The Carry All Pouch for Walker, model 116, is a carrying bag made of blue denim designed to attach to the side of a wheelchair or walker. The pouch has one inside pocket and 3 outside pockets with velcro closures.
Carrying Aids For Wheelchair
CUSTOM ADAPTATION PURPOSE: To enable an individual with quadriplegia to keep essential items at hand while in his wheelchair. Three carrying aids were made and attached the left arm of the wheelchair. The first was a carrying pouch for a cell phone. Made of metal, the pouch is lined with vinyl to protect the phone from damage. The second was a small, flat metal tray to carry the remote control for operating the front door. Also added to the arm was a pocket made of vinyl to carry the hadset for
Carrying Aids For Wheelchairs
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with Friedrich's ataxia to carry staws and plastic bags with her. To ensure straws are available when needed, carry them in a round plastic toothbrush holder fastened with Velcro to the underside of one arm of the wheelchair. To ensure a supply of plastic bags are available for garbage, snacks, or clean-up bags, hooks dog clean-up bags in the dispenser they come in to the wheelchair. MATERIALS: Toothbrush holder, straws, dog clean-up bag
Casbar, The
The Casbar is a wheelchair push handle extension designed to enable a companion or caregiver to push a wheelchair using one hand. The ends of this C-shaped coated steel bar fit over the existing wheelchair push handles and lock in place using two large adjusting knobs to create a single stroller-style handle. On flat surfaces, this device enables the chair to be pushed and controlled with one hand and on inclines and ramps, using two hands makes pushing less difficult than when using the standar
Catch-All (Model Wh190)
The Catch-All WH190 is a under seat net pocket designed for individuals who spend long periods in wheelchairs. Designed for use with rigid ad folding wheelchairs, this device securely attaches with Velcro hook and loop to the bottom horizontal and rear vertical frame tubing forming a catch all net shelf under the wheelchair seat. DIMENSIONS: The widths ranges are 10, 11 to 14, 13 to 18, and 17 to 24 inches. COLOR: Black.
Chairman Series Gel Power Batteries
The Chairman Series Gel Power Batteries are sealed, maintenance free wheelchair and motive power batteries. These batteries are available in 12-volt or 6-volt models that use absorbed electrolyte technology. Gas recombination eliminates corrosive, explosive gasses. The materials are non-spillable, even if the case is damaged. Due to these safety features, these batteries are not restricted for air travel. RECHARGE: These batteries are designed to give 700+ discharge/recharge cycles, and can be r
Chairmate Cup Holder/ashtray Holder (Model F70622-0000)
The Chairmate Cup/Ashtray Holder, model F70622-0000, is a wheelchair drink holder designed for use by individuals who use wheelchairs. The unit features a double-well cup holder and a removable ashtray. The deeper well has a pop-out bottom that accommodates most glasses and cups. The unit can be attached vertically or horizontally on the right or left side of any chair, metal frame-bed, or tubular frame wheelchair bar from 1/2 to 1.25 inches in diameter. DIMENSIONS (LxWxD): 7.75 x 6.25 x 1.75 in
Challenge Platform Wheelchair Rocker
The Challenge Platform Wheelchair Rocker is a rocking attachment for a wheelchair designed for use by individuals with mobility disabilities or spinal cord injury. This device enables individuals to experience the benefits of rocking without transferring from a wheelchair and is designed for individuals with good upper-body strength and a sense of balance. The platform base has minimal arc, requiring users to exert more force to cause rocking movement.Features include entry/exit from the platfor
Channel Armrest Fixture (Model 436F1)
The Channel Armrest Fixture, model 436F1, is a pivoting, elevating armrest designed to be attached to the arm of a wheelchair with a fitted clamp. The swivel configuration allows the armrest to turn on its horizontal and vertical axis for more comfortable positioning. It can also be used to mount and position hand control units for powered wheelchairs.
Chart Holder (Model 93)
The Chart Holder, Model 93 is vinyl pouch sewn to the back of the wheelchair upholstery. It may be used for carrying charts and papers. OPTIONS: Identification stencilling is available.
Child Wheelchair Tray (Model 766C)
The child wheelchair tray fits all wheelchair sizes. The top is made of mar-resistant wood grain laminate and has a 1/2 inch rim. DIMENSIONS: 21 x 18 x 12.5 inches with a 7.5-inch cut out.
Clamp-On Cup Holder (Model 16C035)
The Clamp-On Cup Holder, model 16C035, is a wheelchair drink holder designed for use by individuals who use wheelchairs. This device attaches to most wheelchairs. Once the attachment clip (included) is installed onto the chair, the cup holder itself can be removed as needed. There are no tools required. DIMENSIONS: Attachment clips fit 7/8 and 1 inch tubes.
Classic
The Classic is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The wheel is spin forged from 6061-T-6 polished billet aluminum, with mirror bright surfaces, sealed bearings, and Double walled rims. Hand rim options include quad projections and an anodized or vinyl surface. DIMENSIONS: 24 or 25 inch diameter. CAPACITY: 250 pounds. WEIGHT: 3.9 to 4.4 pounds. COLOR: Polished aluminum, gold, red, blue, purple, or black. H
Clear Acryic Wheelchair Tray (Model H1202)
The Clear Acrylic Wheelchair Tray, model H1202, is a lapboard designed for use by individuals who use wheelchairs. Made of clear acrylic, this tray attaches to the wheelchair armrests, has a round torso cutout, and provides a large surface for eating, working, and other activities.
Clear Acrylic Wheelchair Tray (Model 5000)
The Clear Acrylic Wheelchair Tray, model 5000, is a lapboard designed for use with wheelchairs. The transparent acrylic is lightweight and the universal design fits all wheelchairs. The tray attaches with Velcro straps. DIMENSIONS: 23 x 19 x 1/4 inch.
Clear Acrylic Wheelchair Tray (Model 6662)
The Clear Acrylic Wheechair Tray, model 6662, is a lapboard designed for attachment to a wheelchair with Velcro straps. It is transparent, lightweight and has a universal design. DIMENSIONS (LxWxH): 23 x 19 x 1/4 inches. WEIGHT: 3 pounds.
Clear Non-Glare Acrylic Overlay (Models 11D.3A & 11D.3B)
The Clear Non-Glare Acrylic Overlays are designed for wheelchair trays by Consumer Care Products (model numbers starting with 11D, see separate entries). These overlays may be used for tracing activities and protecting communication aids and other accessories. The overlay snaps in and out. DIMENSIONS: Model 11D.3A is 16 x 20 inches; model 11D.3B is 19 x 24 inches. WEIGHT: Approximately 4 pounds.
Clip on Cup Holder
The Clip on Drink Holder for Walkers and Wheelchairs is a drink holder designed for use by individuals who use wheelchairs or walkers. A plastic coated, steel, spring clip grips the tubular frame of furniture, wheelchairs, walkers , rollators, bed rails, folding shopping carts, and other tubular frames.
Clip-On Glass Holder (Model F74576)
The Clip-on Glass Holder, model F74576, is a drink holder designed to be attached to a wheelchair frame, commode, or other tubular frame haveing a diameter of 0.75 to 1 inch. This helical spring-wound wire holder has a baked-on enamel finish and a plated clip. DIMENSIONS: 2 7/8 inch inside diameter x 3 inches high.
Cloth Lap Tray.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Overcomes the difficulty of a person in a wheelchair to balance objects on the lap. Cloth tray with stiffened edges can be constructed to provide a flat surface on which to place articles. Stiffened edge serves to prevent things from slipping off the tray. Made of 1 and 1/8 yards of fabric or 1/2 yard each of two contrasting fabrics, velcro, and 1 and 1/8 yard rubber tubing or garden hose. COMMENTS: Simple pattern and instructions for construction are
Collapsible Lap Tray.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Wheelchair lapboard folds and stores on back of chair. Lightweight lapboard attaches to full length wheelchair arms. It folds in half and can be used as a short lapboard, or removes and stored easily on the back of the wheelchair. Includes picture. SKILLS REQUIRED: Woodworking AUTHOR: Bob Warren, UCP of Akron, 318 Water STreet, Akron, OH 330-376-6041. TITLE: Tools, Equipment and Machinery Adapted for the Vocational Education and Employment of Handicapp
Colson 0315 Seven Spoke Plastic Wheel
The 0315 Seven Spoke Plastic Wheel is a castor wheel designed for attendant operated wheelchairs. The caster wheel is made of high impact engineering thermoplastic to be virtually corrosion and oxidization free, and easy to clean. The rim section is designed to accept both pneumatic rubber and microcellular polyurethane (MCP) tires. The polyurethane tires have shallow tread patterns so that less debris is tracked indoors. WHEEL DIAMETER: 315mm (12.5 inches). TREAD WIDTH: 45mm (1.75 inches) or 57
Combo Walker / Wheelchair Bag (Model 6434)
The Combo Walker/Wheelchair Bag is a carrying bag or caddy for use by people who use wakers or wheelchairs. The denim bag features four pockets ataches to the front walker bar or wheelchair arm using the attached straps. DIMENSIONS: 13 x 9.5 inches. COLOR: Blue.
Comfort Company Acta-Back
The Comfort Company Acta-Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-back features three layer foam construction, including visco surface layer. The lightweight durable aluminum shell comes with head support holes and lateral hardware slots. Comfort company back has patented compass hardware that quickly installs to wheelchair and adjusts for depth, height, and angle while the user remains seated. Acta-back
Comfort Company Acta-Back Deep
The Comfort Company Acta-Back Deep is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-back deep has three layer foam construction including visco surface. It has lightweight durable aluminum shell that comes with head support holes and has patented moldable aluminum stays that conform and support back. The back provides pelvic and scapular relief. Its patented compass hardware quickly installs to wheelchair and easily a
Comfort Company Acta-Back LTS Back
The Comfort Company Acta-Back LTS Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-back LTS back is a lightweight durable aluminum shell that comes with head support pad holes and lateral trunk support hardware slots. Acta-back LTS has three layer foam construction, including Viscool surface layer and has patented moldable aluminum stays that conform and provides back support, pelvic and scapular relief. Acta-bac
Comfort Company Acta-Contour Back
The Comfort Company Acta-Contour Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort Company Acta-Contour Back is designed to provide lower thoracic relief and support. Comfort Company Acta-Contour back’s patented lightweight moldable aluminum shell stays conform and support the back and comes with head support holes. Comfort Company Acta-Contour Backrest has three layer foam construction, including comfortable Visco surface lay
Comfort Company Acta-Embrace Back
The Comfort Company Acta-Embrace Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-embrace back has aluminum stays on the backside of the two layer foam pad and can be molded to support lumbar, scoliosis, and kyphosis needs. Acta-embrace back has integrated trunk supports that are attached to a planar aluminum backrest shell and can be adjusted for angle, height, and up to a total of 3 inches of width to create a
Comfort Company Acta-Embrace LTS Back
The Comfort Company Acta-Embrace LTS Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-embrace LTS back has integrated trunk supports that are attached to a planar aluminum backrest shell and can be adjusted for angle, height, and up to a total of 3 inches of width to create a custom supportive shape. Acta-embrace back provides extreme stability, pelvic and scapular relief and years of durable use. Acta-embrace LT
Comfort Company Acta-Relief Back
The Comfort Company Acta-Relief Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-relief back has a thick visco surface layer that adds extra comfort and support by contouring to the user's body. Acta-relief back features flexible, adjustable straps that allow the product to offset the center of pressure and better remove pressure points from the spine and allows for a more aggressive molding to each individual pa
Comfort Company Acta-Relief LTS Back
The Comfort Company Acta-Relief LTS Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company acta-relief LTS back is designed to provide more aggressive molding to each individual's natural anatomy and support many seating positions ranging from upright seating to a severely rotated back. Acta-relief LTS back features flexible, adjustable straps that allow this product to offset the center of pressure and better remove pressu
Comfort Company Comfort Back
The Comfort Company Comfort Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company comfort back has a dual density, high resiliency foam that comfortably contours to user's anatomy. Comfort back is available with or without built-in lumbar support and coincides with existing wheelchair back. The back is easy to install. Comfort back support fits 16, 18, 20, 22 inches wheelchair size and has weight capacity of 450 pounds.
Comfort Company Contour Visco Back
The Comfort Company Contour Visco Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company contour visco back features visco surface layer that adds extra comfort and support by contouring to the user's body. Visco back has a dual density, high resiliency foam that comfortably contours to user's anatomy. Contour visco back is easy to install and coincides with existing wheelchair back. The back support fits 16, 18, 20, 22 inc
Comfort Company Elements Foam Wheelchair Back
The Comfort Company Elements Foam Wheelchair Back is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company element back is a general use wheelchair back that has 1inch of pressure relieving foam for a greater level of comfort and support than the standard wheelchair sling back. Element back features an innovative strapping system that can accommodate for kyphosis and provide lumbar support and the back tension is adjustable to fit
Comfort Company Incrediback Moldable
The Comfort Company Incrediback Moldable is designed for use by individuals with lower extremity, mobility disabilities and spinal cord injury. The Comfort company incrediback moldable back has patented moldable aluminum stays that conform to and support the user's back. The standard moldable back is best for the wheelchair user who needs the support and comfort that a normal sling back cannot provide. The incrediback is fully adjustable for angle and height, with 2 inches of depth adjustment. I
Comfort Pad For Economy Molded Lap Tray (Model A707-151)
The Comfort Pad for Economy Molded Lap Tray, model 707-151, is a lapboard overlay designed for use with the Economy Molded Lap Tray (see entry). This pad fits securely within the lip of the tray and is secured with the tray's D-ring straps. The pad has an integral cup/glass recess. OPTIONS: The pad and tray can be purchased separately or as a unit. DIMENSIONS: The pad is 0.5-inch thick.
Comfortarm Armrest
The ComfortArm Armrest is an arm trough designed for use by individuals with spinal cord injury, neurological disabilities, and other mobility disabilities and upper extremity disabilities. Appropriate for individuals with elbow contractures, this unit features a deep arm well, full articulation, and solid mounting. Available for the right or left arm in standard or elevating models, the standard unit allows the arm trough to be elevated and articulated with a quick release lever, while the swin
Comfortline Series
The Comfortline Series are lapboards designed for attaching to wheelchairs. The trays have a rectangular work surface and rounded torso cutout and are fabricated of wood and covered with foam padding and finished with molded satin vinyl. These trays are available in two models: the tray alone or the tray with straps. SIZE: Both models are available in child and adult sizes. DIMENSIONS (WxD): Child-size trays are 20.5 x 18 inches with a 12 x 6 inches torso cutout; adult-size trays are 23.5 x 22 i
Complete Feet
Complete Feet is a foot support designed for use by individuals who use wheelchairs. This foam-padded unit covers the footplates, extends to the calf, and attaches to the chair with heavy-duty straps to help protect and control flaccid feet. The contoured leg troughs have foam in two densities to protect the ankles, reduce abrasions, and allign the legs. Rear cutouts reduce skin breakdown on the heels. DIMENSIONS (HxW): Available for 12 x 16,18,20, and 8 x 16,18,20 inch wheelchairs.
Complete Feet Single Foot
The Complete Feet Single Foot is a foot support designed for use by individuals who use wheelchairs. This foam-padded unit covers the footplates, extends to the calf, and clamps to the footplate to help protect and control a flaccid foot. The other foot remains free for foot propulsion of the wheelchair. The contoured leg trough has foam in two densities to protect the ankle, reduce abrasions, and align the leg. A rear cutout reduces skin breakdown on the heel. DIMENSIONS (HxLxW): 8-10 x 10 x 7.
Composite Caster
The Composite Caster is a caster wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This lightweight composite unit has a smooth finish that promotes easier turning, reduces rolling resistance, and has no tread to collect dirt . DIMENSIONS (Diameter x Width): 4 x 1.25 inches; 5 x 1 or 1.5 inches; 6 x 1 or 1.5 inches; 8 x 1 inches.
Concordia Wheelchair Tire, The
The Concordia Wheelchair Tire is a replacement tire designed for use by wheelchair users. This tire has non-marking and a center ridge for low rolling resistance. DIMENSIONS: 24 x 1.25 inches; this tire also fits 24 x 1 3/8 rims.
Continental Back Pack
The Continental Back Pack is a wheelchair back pouch designed to attach to the chair's handgrips with straps. An inner pocket has a top zipper closure, or a flap with a velcro closure. One large and two small outer pockets are included for access to smaller items. DIMENSIONS: 16 x 16 inches. COLOR: Black or saddle vinyl.
Convertible Roof for Hot-Rod Wheelchair
Convertible Roof for Hot-Rod Wheelchair is designed use by individuals with limited mobility and use a wheelchair for mobility. It provides protection from prolong sun exposure.
Cozy Seat (Models 703005 & 703006)
The Cozy Cushion is a combination foam seat and back cushion with attached armrest pads designed for use with wheelchairs. This one-piece unit is covered in soft brushed poly and padded with high-density foam and prevents skin contact with a wheelchair's vinyl upholstery and metal parts. Covering the seat, back, and armrests, the Cozy Cushion permits use of seatbelts and positioning belts. SIZES: Model 703005 fits 16-inch wide chairs and 703006 fits 18-inch chairs.
Cpsc Standard Back (Models Sb-01 Thru Sb-06)
Seating insert. The standard back has integral waist bolsters that contribute to central positioning of the lower spine. Chest bolsters may be added easily without modifying the upholstery.
Cpsc Standard Pommel Seat (Models Sp-01 Thru Sp-06)
Wheelchair seat insert with integral pelvic bolsters and tapered side sections for pelvic centralization. Has a 15 degree wedged seat, a thigh shelf and an integral abduction pommel to provide good positioning and weight distribution. Standard cushion is removable and vinyl covered. Options include polyfoam or viscofoam cushion, lateral padding, reinforced side panels. 7 sizes: 11 inches wide by 13 inches deep, 12 by 14 inches, 13 by 17 1/2 inches, 14 by 18 inches, 15 by 20 1/ 2 inches, 16 by 20
Cpsc Transfer Seat (Models Ts-02, Ts-04, & Ts-06)
Wheelchair insert with integral pelvic bolsters and tapered side sections for pelvic centralization. Seat has 7 slope and a flat front profile. Unit clips directly over the wheelchair seat frame tubes, it seats the persons lower than normal for easier transfers, while still providing appropriate positioning.
Cpsc Wheelchair Trays (Models Lt 01, Lt 03, Lt 11, & Lt 13)
Wheelchair lapboards, ABS plastic. Safety rim around the perimeter keeps articles from sliding off. Inside edge may be modified as required. The tray attaches to any size wheelchair with brackets.
Cross
The Cross is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The wheel is made from computer machined 6061-T-6 polished billet aluminum. The spokes resemble a maltese cross. It has mirror bright surfaces, sealed bearings, and a double walled rim. Hand rims are available with quad projections and with an anodized or vinyl-coated surface. DIMENSIONS: 24 or 25 inch diameter. CAPACITY: 250 pounds. WEIGHT: 5 to 5.2 pounds.
Crutch Bag For Wheelchair
The Crutch Bag for Wheelchair is designed for use by people with lower extremity, walking or mobility disabilities who use crutches and a wheelchair. This bag, which is available made of nylon, sunbrella, or cordura, provides the means for transport a pair of crutches while seated in a wheelchair. The bag attaches to the back of a wheelchair and fits one pair of crutches in an upright position. It has an outer pocket for additional items and a flap with a Velcro closure. DIMENSIONS (HxWxD): 20.5
Cup Holder
DO IT YOURSELF PURPOSE: To provide powered wheelchair users with the ability to carry beverages. A cup holder designed to clamp to an automotive air vent can be adapted for use on a wheelchair. Zip ties can be used to secure the holder squarely to the frame where it works best for the user. TITLE: Cup Holder. REF: http://www.wheelchairmodifications.org. The organization can also be reached at Wheelchair Modifications, 5533 A Pony Farm Drive, Richmond, VA 23227.
Cup Holder
The Cup Holder is a wheelchair cup, glass, mug, or can holder designed to allow individuals who do not have the use of their hands to drink through a straw from his/her own cup without assistance. The plastic adjustable cup cradle is fixed to the top of a 10 mm stainless steel rod. The rod is mounted onto the wheelchair arm with a plastic connector. The cradle has two openings on either side for a mug handle and will accommodate a wide variety of drinking containers, allowing the user to use a p
Cup Holder 1
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with quadriplegia to drink independently. This cup holder is made using a flexible gooseneck microphone stand with fittings at each end, a machined clamp that fits the wheelchair armrest, a piece of black PVC drain collar, and fence wire. The PVC collar has a notch cut into the side of it to hold a thermal coffee cup, and a wire cage
was added below to hold most juice bottles and soda cans. A piece of fencing wire is placed inside the go
Cursum Stroller
---- PROTOTYPE --------- PURPOSE: To design a prototype of a stroller adapted for a wheelchair to be used by individuals with lower extremity and mobility disabilities, spinal cord injury, and others who use wheelchairs. The Cursum stroller, a wheelchair adaptive stroller, is designed to be used in tandem with a wheelchair. It connects to the front of a wheelchair. Swivel wheels, complete height adjustment, attention to comfort and visibility, and advanced safety features give parents with disab
Curtis Pmc Speed Controller (Model 1203A)
The Curtis PMC Speed Controller, model 1203A, is an electronic acceleration and speed limiter designed for heavy duty permanent magnet motor applications for wheelchair users. It offers infinite y adjustable drive and brake control; automatic dual ramp reversing; adjustable reversing speeds; regenerative braking; a high frequency (silent) operation with low end torque, and thermal protection in case of overheating. This speed controller is compatible with most motor units, and the main power con
Curtis Wheelchair Battery Fuel Gauge (Model 900W)
Battery gauge monitors charge for any lead acid deep cycle 12 or 24 volt wheelchair battery. LED bar displays battery charge level. Attaches to arm of chair in view of user with a hook loop fastening system. Alarm flashes once when battery is low and needs recharging, double flashing light indicates battery is near dead. When on empty, wheelchair can still travel short distance. Unit resets to full when charge is 80 percent complete and charge takes another 2 or 3 hours to complete. Display ligh
Curved Transfer Board
The Curved Transfer Board is a transfer board designed for use by individuals who use wheelchairs. Made of solid, reinforced, waterproof plastic that resists chipping, shattering, and splintering, this board has tapered ends and a smooth surface for easy sliding. The curved design accommodates a variety of transfer situations, and slip-resistant pads on the underside at each end increase stability. DIMENSIONS: 27 5/8 inches long and 14 5/8 inches wide tapering to 10 1/8 inches wide in the middle
Cushion Stop (Model 5035)
The Cushion Stop, model 5035, is a cushion retainer designed to prevent a cushion from sticking out the back of a wheelchair. The heavy cotton duck fabric insert attaches permanently to the seat and back of the wheelchair to prevent the cushion from sliding out. Grommets in the webbing straps attach to the upholstery screws on the back and seat. SIZE: For standard adult or narrow adult wheelchair.
Custom Footplates
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create custom adapted footplates for an electric wheelchair used by an individual with reduced mobility and strength. When this individual sits in her chair with the footplates at a comfortable height for her, they rubbed on the wheels, particularly when she was turning. Additionally, this individual did not have enough strength in her feet to push the footplates up out of the way when she wanted to get out of the chair. Sometimes a care giver co
CutiePie
The Pie Bag is a carrying bag for a walker or a wheelchair back pouch designed to enable persons with mobility disabilities to transport personal items. The top stabilizers fit a wide variety of wheel sizes, spoke configurations, walker, bicycle, and scooter options. It is waterproof and washable. Other features include:
Cycl-One 3, 12, 48
The Cycl-One is a cycle attachment for manual wheelchairs designed to transform the chair into a hand-propelled cycle. The attachment consists of a front wheel, handcrank shaft, and attachments for mounting onto the wheelchair frame. FRAME: The frame is made of high tensile steel tubing and the crankset is alloy with a 28-tooth chainring (3 and 12 speed models) and 34 tooth chainring on the 48-speed model. HANDLES: The "together"-style hand pedals with parallel horizontal handgrips are designed
Cylinder Rack (Model De-1-W)
The cylinder rack is a cylinder cart for wheelchair that fits on back of wheelchair attached with small wrench Nylon screw on holding ring secures cylinder in place. It holds D or E cylinders and has bright chrome plating. Does not interfere with operation of chair. (IV Pole not included).
Daessy Desktop Mount (Model Ddm-1)
The Daessy Desktop Mount, model DDM-1, is a mounting clamp designed to hold a communication device for individuals who have physical disabilities and use a communication device. The desktop mount provides a stable, hands-free support for any flat surface. It is ideal for individuals who have limited upper limb mobility. The stand comes with the Quick Release Mount, which holds the device firmly yet allows you to remove it with just a flip of a lever.
Daessy Folding Mount
The Daessy Folding Mount is a wheelchair mounting system for communication devices. The unit provides a solid, stable platform that can be adjusted to meet the positioning needs of each individual. The communication device and platform can be rotated down and out of the way beside the wheelchair to permit close-in positioning to a desk or table. Models are available for 7/8-inch tubing, .75-inch tubing, and 1-inch tubing, all in a choice of 6- and 12-inch offset.
Daessy Mini Adjustable Mount (Model M75-Am)
The DAESSY Mini Adjustable Mount, model M75-AM, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system has several points of adjustment to set up and position the mount. Two rotating joints can be angled and twisted in various directions to adjust the horizontal tube position. The system is supported on the wheelchair by a
Daessy Mini Bent-Tube Mount (Model M75-Btm)
The DAESSY Mini Bent-Tube Mount, model M75-BTM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. This product also can be removed from the wheelchair when not needed. The frame clamp assembly includes a
Daessy Mini Folding Mount (Model M75-Fm)
The DAESSY Mini Folding Mount, model M75-FM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. The system folds the horizontal tube down to the outside. The folding joint between the two mount tubes brin
Dane Wheelchair Mover
The WheelChair Mover uses a simple hand lever design that activates secure hitching to the frame of the wheelchair. The ergonomic design of the machine allows the user to control the speed with easy and controlled throttle acceleration. With the unit securing the frame at a low center of gravity, turning the wheelchair in a circle is smooth and effortless. Compact and quiet, the Dane WheelChair Mover is the ideal device to fit within hospital rooms and halls while meeting the objectives of safe
Davis Suspension Forks
Shock absorbing suspension caster fork for wheelchairs. For semipneumatic and pneumatic caster tires. Fits most wheelchairs. Fork sandwiched with additional plate, fastened by bolt with spring to absorb vibrations.
Day Cruiser Mini Pack
The Day Cruiser Mini Pack is a wheelchair side or legrest pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made from water-resistant heavy-duty Cordura with a full lining, this pack attaches to the armrest or legrest of a wheelchair with two Velcro straps, which are sewn on the back of the unit. It can also be worn around the user's neck. The pack has two compartments, an adjustable neck strap, and a sewn-on elastic loop on the side to carry glasses or a pe
Day Cruiser Wheelchair Bag
The Day Cruiser Wheelchair Bag is a wheelchair back pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made from water resistant heavy-duty Cordura with a full lining, this backpack attaches to most wheelchairs with or without push handles with two adjustable straps. The backpack has two compartments, a large main area with Velcro flap closure and an expandable zippered front pocket for smaller items. Power chair users must have handles to attach the bag. DIM
Deep U Headrest (Model Duhr100)
The Deep U Headrest, model DUHR100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who need to keep their heads positioned upright and centered. DIMENSIONS: 11 x 5 inches.
Deluxe Down-Under (Model Wh175) & Junior Down-Under (Model Wh175J)
The Deluxe Down-Under WH175 and the Junior Down-Under WH175J are removable under seat pockets designed for use by wheelchairs users. The bags have one main compartment and an additional outside pocket suitable for carrying a checkbook, wallet, small book, wheelchair tools etc. The pockets have zip closures with large pull rings. The Junior Down- Under is sized for small chairs. DIMENSIONS (WxHxD): Deluxe Down-Under - 11x7x3 inches; Junior Down-Under is 9x7x3 inches. COLOR: All black or black wit
Deluxe Lateral Arm Support (Model 6320)
The Deluxe Lateral Arm Support, model 6320, is a trunk support designed for use by wheelchair users who lean laterally. This padded trough has an ambidextrous design, enabling it to fit either wheelchair armrest. The contoured trough supports the arm and encourages arm use and rehabilitation. Optional self-releasing straps may be used to stabilize arm position. This support has a soft, water-repellent, wipe-clean vinyl cover.
Deluxe Open Front Shower And Commode Chair
The Deluxe Open Front Shower And Commode Chair is designed for use by individuals with balance or mobility disabilities. The commode has four interlocking seat supports for strength and a wide wheel base for stability. It comes with a removable back made of durable vinyl coated polyester mesh. Its design eliminates all sharp points, permitting safe patient transfers. It is made with Healthcare grade PVC that does not rust, chip, stain or corrode. The shower chair and seat is stable, easy to clea
Deluxe Reversible Extenda Arm (Model 31094)
The Deluxe Reversible Extenda Arm, Model 31094, is lapboard mounting hardware designed for use with wheelchairs. The tubulat steel telescoping arm mounts under the armrest on standard padded or desk-length wheelchair arms to provide up to 8.5 inches of additional support for trays in front of the armrest. The device can also br retracted under the armrest overhang. This deluxe heavy duty version is reversible for use on the right or left side. WARRANTY: The manufacturer warrants this product to
Deluxe Saddle Armrest Bag
The Deluxe Saddle Armrest Bag is designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. The bag straps over the user's scooter or wheelchair armrest to provide a handy storage area for keys, wallet, cell phone, glasses. The storage bag is designed with side pockets and a zippered interior pocket that keeps personal belongings. Additionally, the bag can be mounted to inside or outside of armrest.
Deluxe Self Propelled Shower And Commode Chair
The Deluxe Self Propelled Shower And Commode Chair is designed for use by individuals with balance or mobility disabilities. The commode is made with healthcare grade PVC that does not rust, chip, stain or corrode. This shower chair has four interlocking seat supports for strength and a wide wheel base for stability. Additionally, it comes with a removable back which is made of durable, vinyl-coated polyester mesh.
Deluxe Transfer Board (Models Nc94205 & Nc94205-B)
The Deluxe Transfer Board, models NC94205 and NC94205-B, is designed to assist people who use wheelchairs. The Deluxe Transfer Board (NC94205) is made from 0.5-inch thick birch and tapers at both ends for transfers. The Bariatric Transfer Board (NC94205-B) features two hand holes and a heavy duty 9 ply birch wood base with 3 additonal piles form-laminate on top. CAPACITY: 450 pounds for NC94205 and 650 pounds for NC94205-B. DIMENSIONS (WxL): 8 x 24 inches for NC94205 and 10 x 32 inches for NC942
Deluxe Wheelchair Mac with Sleeves
eluxe Wheelchair Mac (raincoat) with Sleeves is designed to provide protection of the elements for individuals who use a wheelchair for mobility. It has a seam sealed for waterproofing. The knitted cuffs are covered by the ends of the sleeves, to prevent the fabric from getting wet. Vents at the rear of the raincoat allow use of the wheelchair’s pushing handles and a small pouch at the front provides handy storage.
Deluxe Wheelchair Tray (Models H1200 & H1201)
The Deluxe Wheelchair Tray is a lapboard designed for use by individuals who use wheelchairs. The wooden tray features extra-wide, screwed-in straps for attaching the tray to the wheelchair armrests, a rounded torso cutout, and a raised lip to prevent items from falling off. DIMENSIONS (WxD): 25 x 22 inches. COLOR: Model H1200 is butternut and model H1201 is rosewood.
Deluxe Wood Transfer Board
The Deluxe Wood Transfer Board is designed for use in transfers to and from wheelchairs. This solid hardwood board has tapered ends and is urethane coated, sealed, and polished for smoothness. The board has a cut-out handle for gripping and carrying. DIMENSIONS (LxW): 30 x 8 inches. CAPACITY: 250 pounds.
Depends Holder Bag (Model St107)
The Depends Holder Bag, model ST107, is a carrying bag designed for attaching to a wheelchair for individuals who use a wheelchair. This bag provides easy on/off handling and is made from light weight canvas. OPTIONS: Silk screening with your logo or message in a variety of colors is available upon request. DIMENSIONS: 16 x 24 with a 5.5 inch gusseted bottom. COLORS: Body color comes in natural. Assorted webbing and trim colors are available.
Desk Arm / Large Lap Hugger (Models 6515L, & 6517)
The Desk Arm/LargeLap Hugger is a torso support designed to prevent forward leaning by people who use wheelchairs. This foam padded support is covered with wipe-clean vinyl and fits between the wheelchair user and the wheelchair frame and also provides arm support. Notches fit around the armrest posts. DIMENSIONS: Model 6517 fits wheelchairs 18 to 20 inches wide with desk-length arms and model 6515L fits wheelchairs 20 to 24 inches wide.
Desk-Length Armrest (Model Ar20) And Full-Length Armrest (Ar24)
The Desk-Length Armrest (model AR20) and Full-Length Armrest (AR24) are single post armrests that come with mounting hardware and are designed for use on seating systems. They can be attached to aluminum pans to be non-removeable, removeable with fixed height, or height- adjustable with fixed lower limit. Desk-Length Armrests are 9 inches long and Full-Length are 14 inches long.
Detachable Laptray With Electronic Talking Communicator.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Laptray to securely hold electronic communication device on wheelchair lapboard. A hinged vacuum formed plastic housing was designed to clamp to the desk arms of a wheelchair. By lifting the laptray the individual has immediate access to the communicator, yet it is concealed when it is not in use. The top of the laptray provides a working surface for the individual. Includes photographs. SKILLS REQUIRED: Plastics, woodworking. AUTHOR: David Law, Jr., W
Device To Attach Pram (Child's Stroller) To Wheelchair
CUSTOM ADAPTATION PURPOSE: To design and build a removable device which would lock a pram (child's stroller) into position at the front of a wheelchair for a person with paraplegia. Several ideas were considered but the final solution involved lifting the back wheels of the pram off the ground and putting the weight on the front pram castors and the front wheelchair castors. Lightweight 16-millimeter square steel tubing was used to build a frame which clamps in place on both wheelchair and pram
Diestco Armrest Front Bag
The Diestco Armrest Front Bag is a caddy for a scooter or powered wheelchair designed for use by individuals with mobility disabilities or spinal cord injury. This large basketball-shaped and sized bag mounts to the end of armrests with the included straps and is detachable when not in use. Made of water-resistant nylon, this bag has a lightweight aluminum frame to retain the shape and a zippered top cover. DIMENSIONS: 7 inches high x 12 inches in diameter.
Diestco Armrest Pocket
The Diestco Armrest Pocket is a wheelchair side pocket designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Made of waterproof nylon, the pocket attaches to the wheelchair armrest with the included straps. DIMENSIONS: 11 x 5 x 3 inches.
Diestco Cargo Shelf
The Diestco Cargo shelf is an under seat pocket designed for use by individuals with lower extremity, mobility, or neurological disabilities or spinal cord injury. This mesh shelf attaches to the frame of manual wheelchairs underneath the seat with the included hook-and-loop straps. DIMENSIONS(WxD): 15 x 16 inches.
Diestco Deluxe Armrest Saddle Bag (Model B2121)
The Diestco Deluxe Armrest Saddle Bag, model B2121, is a wheelchair or scooter side pouch designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. Made of water-resistant nylon, this pouch can be mounted on the inside or outside of an armrest on a scooter or wheelchair. This pouch has one flap-covered main compartment, side pockets, a zippered interior pocket, and two small outside pockets for a cell phone or glasses. DIMENSIONS(WxLxD): 10 x 8 x 3 inch
Diestco Deluxe Seatback Bag
The Diestco Deluxe Seatback Wheelchair Bag is a wheelchair or scooter back pouch designed for use by individuals with lower extremity, severe physical, or mobility disabilities or spinal cord injury. Made of water-resistant nylon, this pouch attaches to the seat back with the included harness-style mount. The bag can be used with captain-style scooter seats or with wheelchairs with push handles. The bag has several pockets, including a back mesh pocket, a zippered back pocket, side pockets, and
Diestco Down-In-Front Wheelchair Bag
The Diestco Down-in-Front Wheelchair bag is an under seat pocket desighed for use on manual wheelchairs without armrests. Made of water-resistant nylpn, this single-pocket bag attaches to the lower front frame of the wheelchair behind the user's legs with buckle-closure straps. DIMENSIONS(WxLxD): 11 x 6 x 3 inches.
Diestco Extra Large Armrest Saddle Bag (Model 2131)
The Diestco Extra Large Armrest Saddle Bag, model B2131, is a wheelchair or scooter side pouch designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. Made of water-resistant nylon, this pouch mounts on a scooter or powered wheelchair armrest and has a front zippered pocket, mesh pockets in front and on the sides, an inside pocket, side loops, and a secret pocket. DIMENSIONS(WxLxD): 12 x 16 x 2 inches.
Diestco Fabric Cane And Crutch Holders (Models B6213 & B6313)
The Diestco Fabric Cane and Crutch Holders are cane or crutch holders for wheelchairs or scooters side pouch designed for use by individuals with mobility, walking, or lower extremity disabilities. Made of water-resistant nylon, this carrier is shaped similarly to a golf bag and is available with a mounting system for use on captain-style scooter seats or wheelchairs without push handles (model B6213) or on wheelchairs with push handles (model 6313).
Diestco Large Armrest Saddle Bag (Model B2125)
The Diestco Extra Large Armrest Saddle Bag, model B2131, is a wheelchair or scooter side pouch designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. Made of water-resistant nylon, this pouch mounts on a scooter or powered wheelchair armrest and has a variety of pockets and compartments. DIMENSIONS(WxLxD): 9 x 12 x 3 inches.
Diestco Mid-Range Seatback Bag (Model B1117)
The Diestco Deluxe Seatback Wheelchair Bag, model B1117, is a wheelchair or scooter back pouch designed for use by individuals with lower extremity, severe physical, or mobility disabilities or spinal cord injury. Made of water-resistant nylon, this pouch attaches to the seat back with the included harness-style mount. The bag can be used with captain-style scooter seats or with wheelchairs with push handles. The bag has several pockets, including a back mesh pocket, a zippered back pocket, and
Diestco Monster Seatback Bag (Model B1113)
The Diestco Monster Seatback Bag, model B1113, is a wheelchair or scooter back pouch designed for use by individuals with lower extremity, severe physical, or mobility disabilities or spinal cord injury. Made of water-resistant nylon, this pouch attaches to the seat back with the included harness-style mount. The bag can be used with captain-style scooter seats or with wheelchairs with push handles. The bag has a lightweight aluminum frame to keep it open. DIMENSIONS(WxLxD): 13 x 18 x 10 inches.
Diestco Standard Seatback Wheelchair Bag
The Diestco Standard Seatback Wheelchair Bag is a wheelchair or scooter back pouch designed for use by individuals with lower extremity, severe physical, or mobility disabilities or spinal cord injury. Made of water-resistant nylon, this pouch attaches to the seat back with the included harness-style mount. The bag has a zippered top. DIMENSIONS: 12 x 12 x 3 inches.
Diestco Universal Cup Holder
The Dietsco Universal Cup Holder is a wheelchair drink holder designed for use by individuals with mobility disabilities or spinal cord injury. This holder attaches to the wheelchair or scooter armrest with the included mounting hardware.
Dino Wheel
The Dino Wheel is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The wheel has a hub milled from a solid piece of billet aluminum, with 12 tubular aluminum spokes, and double wall deep V aluminum rims. The wheel is lightweight and responsive to the user's push, and it has the strength for everyday use. The low spoke count allows access through the wheel. The wheel has standard 6-tab handring mounting holes. The maxim
Direct Mount Clamp (Model 247-Dm100)
The Direct Mount Clamp, model 247-DM100, is lapboard mounting hardware designed specifically for attaching the MYDESC desktop lapboards (see separate entries) to wheelchairs without armrests or without removable armrests. This metal clamp block has a tightening knob for use with tube framing from 0.75 to 1.25 inches in diameter. The device can be mounted either vertically or horizontally, and also features an 0.83-inch cylinder slot to mount the lapboard, or umbrellas, directly onto the wheelcha
Disposable Wheelchair Cover (Model Mc-5)
The Disposable Wheelchair Cover, model MC-5, is designed to protect manual and power wheelchairs, commodes, oxygen tanks, etc. DIMENSIONS: 28 x 22 x 35 inches. COLOR: Clear plastic.
Diy Snow Tires
--- DO IT YOURSELF ENTRY --------- PURPOSE: To create do-it-yourself snow tires for manual or powered wheelchair for individuals with mobility disabilities. Acquire sturdy/plastic wire ties that are long enough to go around the thickness of the wheelchair’s tire and wheel (approximately 6.5 to 8 inches and 50 pound strength or more). Depending on the size of the wheelchair’s wheel and tire, tie approximately 25 to 30 ties evenly around each wheel and tire of a manual wheelchair. Power wheelchai
Down-Under Shelf (Model Wh185)
The Down-Under Shelf, model WH185, is an under seat carrying caddy designed for use by individuals who spend long periods of time in wheelchairs. Designed for rigid wheelchairs, this caddy attaches under the chair with Velcro straps and provides ample space for school books, shopping items, clothing, etc. DIMENSIONS (HxWxD): 4 x 14 x 11 inches. COLOR: Black.
Drink Holder
The Drink Holder is a wheelchair drink holder designed for use by individuals with lower extremity, mobility or walking disabilities or spinal cord injury. The unit consists of a stainless steel frame with a clamping system for attaching to a chair, crutches or walker. The clamp has a rubber grommet to prevent scratching, along with an adjustable Velcro tightening strap. The holder can be carried in the user's wheelchair bag until it is needed. An insulated beverage jacket is included. It can al
Drink Holder
CUSTOM ADAPTATION PURPOSE: To provide a means for an individual with severe phyical disabilities to carry beverages. A chrome-plated curtain rod was used to make a vertical tube system that fits into brackets installed on a wheelchair. A horizontal crossbar supports a plastic container which, in turn, holds a cup or glass that the user can access with a straw. TITLE: Easels, Calling Systems and More. JOURNAL: TAD Journal. REF: Volume 24, Number 4, Summer 2004: P. 16-17. PAGES: 3 (including cove
Drinkup Travel Lite
The Drinkup Travel Lite is a wheelchair drink holder with a long straw designed for people who have lower extremity or mobility disabilities and spinal cord injury and grasping, fine motor, upper extremity, severe physical disabilities or upper extremity amputation. The Drinkup Travel Lite consists of a water bottle cage with a bracket so it can be attached to the backrest frame of a wheelchair. It has a semi-rigid flexible arm that extends upward past top of backrest and forward around to the f
Drive Power Mobility Armrest Bag
The Power Scooter Armrest Bag is designed for use by individuals who use a wheelchair. The Power Scooter Armrest Bag fits over the user’s power scooter or wheelchair's armrest. The top of the bag is padded providing additional comfort for the user’s arm rest. This Power Scooter Armrest Bag is equipped with four pockets as well as a mesh drink holder to aid in transporting accessories such as; drinks, cell phones, books and other personal items.
Drop Base
The Drop Base is a ABS plastic solid seat panel with cutouts for wheelchair cross braces designed to allow the mounting of custom or commercial seat cushions level with or below seat rail level. The panel fits between the seat rails, with 1- and 2-inch drop hooks to fit 7/8-inch or 1-inch rails. DIMENSIONS: Sized to fit 16 and 18 inch widths.
Drop Seat And Cushions (Models 6540, 654020, 6541, & 6519)
The Drop Seat and Cushions is a solid seat insert and a gel and foam or foam seat cushion designed to lower the height of wheelchair seats to enable self-propulsion using the feet or to enable the user to reach the footplates to stop sliding. This seat can be used with standard or hemi chairs and lowers the center of gravity, making the chair less likely to tip. This seat attaches to the frame in place of the standard seat without the use of tools. A drop seat gel and foam cushion to reduce the
Drop Seat Base And Hardware
The Drop Seat Base ($42.50) and Hardware ($169) are a combination solid seat insert and adjustable hook hardware designed to fit 7/8 or 1 inch diameter wheelchair seat rails. Gravity hook assemblies allow automatic locking of the seat base onto the frame. It requires cutting of the plate to accommodate wheelchair cross-frame tubes, and drilling to mount hardware in appropriate locations.
Drop Seats (Models 31649, 31651, 31655, & 31656)
Drop Seats are solid seat inserts are designed for use by individuals who use wheelchairs. Made of seven-ply birch, these seats have pre-drilled mounting holes and include T-nuts. Cutout slots fit around chair frame crossmembers. DIMENSIONS: Model 31649 fits chairs with 14-inch seats and is 14 x 11 inches; model 31651 fits chairs with 16-inch seats and is 15 x 13 inches; model 31655 fits chairs with 18-inch seats and is 17 x 15 inches; and model 31656 fits chairs with 20-inch seats and is 19 x 1
Drop-Stop Footrest Extender /legrest Pad(Series 7032)
Drop-Stop is a footrest extender designed to prevent foot drop in people who use wheelchairs. The modular extenders create a platform which enables footrests on footrests and geri chairs to be raised from one to four inches to provide improved positioning, sliding control, and weight distribution. The included padded legrest cushion prevents the user's feet from sliding off the footrests. DIMENSIONS: Available in 16- and 18-inch widths and in a choice of one, two, three, or four inches high.
Dual Purpose Oxygen Cylinder Holder (Model Cs1200)
The Dual Purpose Oxygen Cylinder Holder, model CS1200, is an oxygen cylinder carrying case designed for use by individuals with respiratory disabilities who use either a wheelchair or a walker. This dual purpose unit allows the user or a caregiver to move oxygen cylinders from a wheelchair to a two-wheeled walker and back. The unit attaches to most two-wheeled walkers and most wheelchairs, including bariatric wheelchairs. The unit is made of polyester with Velcro straps for attaching to the whee
Dual Tilt In Space With Shear-Controlling Power Recline Systems
Dual Tilt in SpaceShear-Controlling Power Recline Systems are powered reclining systems designed for use with power-base style powered wheelchairs. This system fits Invacare, Quickie, Jazzy, Everest & Jennings power bases and offers a full 90 degrees of tilt and 57 degrees of tilt or any combination in between. This system slides the seat backward as the seat back reclines, taking pressure off sensitive areas and controlling shearing in the lumbar, sacral, and ischial regions. Standard featu
Duet, The
The Duet is a wheelchair tandem cycle designed to provide recreational transportation for two: a wheelchair user or rider with partial or severe physical disabilities, cognitive or visual disabilities, or a pediatric or geriatric passenger, and a non-disabled cyclist. The engineering of the cycle allows passengers from 20 to 275 pounds to fit comfortably by simple adjustments or by using a combination of matching upholstery accessories, seat cushions, and supports. Larger passengers are as easy
Durasoft Half Tray
The DuraSoft Half Tray is a swing-away lap tray designed for use as a wheelchair accessory by individuals with lower extremity or mobility disabilities or spinal cord injury. For those people who do not need the surface area that a full lap tray provides, the DuraSoft Half Tray provides a smaller surface on one side of the wheelchair. It is available in left- and right-handed models. The unit has a rigid insert covered by high resiliency foam with a solid cover. A raised outside edge keeps the u
Dynamic Articulating Footrest
The Dynamic Articulating Footrest is a footrest extender designed for use by people with lower extremity or mobility disabilities or spinal cord injury and others who use a manual or power wheelchair. This footrest extender allows for both extension and rotation of the footplates to mimic the motion of the knee joint and leg. It also allows for three different ranges of articulation (knee rotation): 0 degree (linear motion only), 30 degrees and 50 degrees. A shield is used to prevent pinch point
Dynamic Forehead Strap System (Model Dfs-1)
The Dynamic Forehead Strap System is a headrest accessory designed to support the head for individuals who have difficulty maintaining their head in an upright position. It is meant for use with the S.O.F.T. headrest system (see separate entry). The system consists of pulleys that allow the forehead band to move with the user, providing greater freedom of movement. The strap is designed to float about freely with the user. The straps are available in two different styles. The first features a te
E Z Back System (Models Ezl2001, Ezl2002, & Ezl2003)
The E Z Back System, models EZL2001, EZL2002, and EZL2003, is a back support that can be mounted on sling back wheelchairs, commodes, driver or automobile passenger seats, or chairs. The system includes two laterals, a Velcro back, and a front panel with lumbar support. The system's lateral supports are independent of one another, so they are interchangeable from side to side. The system's lumbar support is also adjustable, so the system can give the user needed lateral or pelvic support. OPTION
E-Motion
E-Motion is a power assist for wheelchairs designed for use by individuals with mobility disabilities. This unit can be retrofitted to most manual wheelchairs simply by replacing the existing rear push wheels with the e-motion wheels and installing a universal bracket on the wheelchair frame. The quiet brushless, gearless electric motors are located in the wheel hubs. The unit offers three different levels of power that can be selected at the touch of a button. Stage 1 offers a 30 percent power
E-Z-Lock Tray Clamp (Model 31096)
The E-Z-Lock Tray Clamp, Model 31096, is lapboard mounting hardware designed to secure lapboards and trays to wheelchairs. This clamp is designed to attach any tray to any wheelchair arm using a simple locking motion. OPTION: An attaching hardware kit for securing the clamp to the tray is available separately ($10.50). WARRANTY: the manufacturer warrants this product against defects in workmanship and materials for 90 days from the date of purchase.
Ease-A-Bump, Wheelchair Bumper
Wheelchair bumper fabricated of 1 inch wall steel tubing. Covered in urethane foam padding with nylon cover. Weighs 5 pounds. Attaches to most wheelchairs with swing away foot rests. 13, 15, and 17 inch widths. Specify width of chair when ordering. Black.
Easy Flex Mount
The Easy Flex Mount is a flexible mount to allow users in wheelchairs to access cups and bottles while in their chairs. Designed with an adjustable Velcro strap that enables the user to access cups and bottles, it also has a flexible tube that can be positioned to meet the needs of the user. The Mount’s easy-to-use clamp attaches to wheelchairs, tabletops, strollers and high chairs
Easy Flex Triple Mount
The Easy Flex Triple Mount allows wheelchair users to mount heavier objects such as tablets and switches. Still flexible and easy to position but more stable and secure with greater protection for your devices. Comes with Velcro mounting plate.
Easy Platform Wheelchair Rocker
The Easy Platform Wheelchair Rocker is a rocking attachment for a wheelchair designed for use by individuals who use wheelchairs. This device enables the user to experience the benefits of rocking without transfering from a wheelchair. The rocker features entry/exit using a rear ramp. The adjustable front caster stops center the wheelchair on the platform and two safety straps secure the wheelchair to the platform for added security. DIMENSIONS (LxW): 48 x 30 inches.
Easyriser (Model Pl24Aj)
The EasyRiser, model PL24AJ, is a foot support designed to prevent pain in the back shoulders or arms for individuals whose workstation is standing at a tall counter. There is an anti-fatigue mat that provides cushioned comfort for the feet and legs and the sturdy steel frame and legs are built for durability. The platform adjusts to put the user at the right height to reduce fatigue and back strain, and the rubber feet hold the platform in position. The foot support is large enough to move arou
Econoglide Transfer Boards
The Econoglide Series are Transfer boards designed to assist people with physcial disabilities in transferring from one surface to another. The boards are fabricated high density stress-relieved linear plastic. The moisture-proof boards are striate-sanded on one side and buff-sanded on the other. Models include the plain board, board with telescope and hand hole, board with hand hole, board with 2 hand holes, board with hand hole and notches, and board with 2 hand holes and notches. CAPACITY: 40
Economy Molded Lap Tray (Model A70711)
The Molded Lap Tray, model A70711, is a lapboard designed for use by individuals with mobility or lower extremity disabilities who use wheelchairs. The lap tray is designed to enable the user to eat or do other activities from their wheelchair and to provide some protection from spills. The tray fits standard and desk arm wheelchairs and includes a cut-out area to accommodate the torso. Other features include a molded recess area for holding a cup or glass. OPTIONAL: A Comfort Pad (see separate
Economy Wheelchair Belt (Model Mdt829110C)
The Economy Wheelchair Belt, model MDT829110C, is a wheelchair seatbelt designed for use by individuals with mobility disabilities or spinal cord injury. This seatbelt restraint helps the wheelchair user to remain upright in the chair without sliding. This belt encircles the user and crosses in back. The belt is made of washable nylon and is latex-free. SIZES: One size fits all.
Econoslide Series Transfer Boards
Econoslide Series Transfer Boards are designed to assist people who use wheelchairs. The 20 models of these boards are made from defect-free 7-ply birch plywood and have rounded corners, ends, and edges. The surface is machine-sanded and finished with clear lacquer. Models include the plain board, board with hand hole and telescope, board with hand hole, board with hand hole and notches, board with 2 hand holes, and board with 2 hand holes and notches. CAPACITY: 400 pounds. DIMENSIONS: All model
Econotray Series
The EconoTray Series are lapboards designed for use on wheelchairs. Fabricated of tempered hardboard with a woodgrain vinyl top, the trays are available in five models: the tray only, tray with 3-piece wood rim, tray with straps, tray with rim and straps, and tray with straps, pads, and a back strap. The Juvenile tray has an oblong worksurface, while the other models have a square worksurface. SIZE: The tray with straps, pad, and backstrap is available only in an adult size. The other models com
Eight-Ten Pac (Model Wh810)
The Eight-Ten Pac is an under seat pocket carrying accessory designed for use by individuals who spend long periods of time in a wheelchair. This carrying aid attaches to the frame of wheelchairs and hangs under the seat behind the user's legs. Features include SR-ADST Side Release Adapt A Straps system for quick attachment and detachment, and a large circular custom pull ring for easy detection and opening. This bag is made in the USA of highly durable nylon fabric with nylon tape bonded seams.
Elbow Support For Wheelchair
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted elbow support for a wheelchair user with hemiparesis following stroke. Following a stroke this individual experienced muscle weakness in her left arm which also affected her sitting balance. When sitting in her Sunrise Breezy wheelchair, her left arm would slip off the narrow armrest and she would fall sideways. Working with her occupational therapist, a commercial project was tried as a solution but proved to wide for th
Electric Wheelchair Power Socket
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with communication disabilities who uses a powered wheelchair to power a laptop computer with augmentative communication software using the wheelchair battery. Speech software was needed during school hours; however, the computer battery did not have sufficient capacity to meet the demand. To be heard in class, powered speakers were also needed, which further diminished operating time. A portable solution was necessary to enable the speec
Elevated-Arm Lateral Support (Models 706020 & 706021)
The Elevated-Arm Lateral Support is a combination lateral trunk support and elevating armrest designed for use by individuals who use wheelchairs or geri chairs. This support, which comes with a launderable synthetic sheepskin cover, helps reduce leaning to one side while permitting the arm to be elevated to control edema. Model 706020 is a right-handed model and model 706021 is a left-handed model. DIMENSIONS: Both models are 12.75 inches high at the lowest point.
Eliminator, The
The Eliminator is an airless cushion innertube designed for flat free use. It is lightweight, easy to install and shock absorbent. The arched web in the tube's interior protects from overload and permanent deformation. It may be used with standard tires of wheelchairs and bicycle tires, and can be reused when the tire wears out. DIMENSIONS: From 8 x 1.25 inches to 24 x 1 3/8 inches, at least 17 different sizes listed. WEIGHT: Can support over 200 pounds. WARRANTY: 2 year limited. COLOR: 14 avail
Endoflex Back
Contoured back with internal metal frame. Mounts in wheelchair frame with back hooks with nylon straps and buckles. Back height and back angle adjustable. Mid-back can flex or be fixed in one position. Vinyl or fabric. .
Endurance D / E Cylinder Holder For Wheelchairs (Model R103E)
The Endurance D/E Cylinder Holder for Wheelchairs, model R103E, is a cylinder cart for wheelchairs designed for use by individuals with mobility and respiratory disabilities. Made of chrome-plated steel, this carrier attaches to the seat back uprights of most wheelchair brands and accommodates D and E size oxygen cylinders.
Enduroline E-Z Lock Quik-Fit Trays (Models 33003P, 33004P, 33005P, 33020P, 33003, 33004, 33005, & 33020)
The Viewline E-Z Lock Quik-Fit Trays are lap trays designed for use with wheelchairs. These trays feature an E-Z Lock Clamping System that adjusts for standard or thick arm pads, enables the tray to slide on to the armrests from the front, and secures the tray with a simple locking motion. These trays are made of melamine-impregnated fiberboard. Models 33003P, 33004P, 33005P, and 33020P have a black PVC rim. The other models do not have a rim. SIZES: Child (fits wheelchairs 12 to 14 inches wide)
Enduroline Plus Trays (Series 31200)
The Enduroline Plus Trays are lap trays designed for use with wheelchairs. These trays are made of melamine-impregnated fiberboard. These moisture-resistant trays can be attached using the E-Z Lock Clamp, Top Drop Clamp, Tube Arm Braxkets (not included), or other attaching system. Models include the tray only, tray with hook-and-loop attaching straps, tray with a PVC rim, and tray with straps and rim. SIZES: Child (fits wheelchairs 12 to 14 inches wide), adult (fits chairs 14 to 17 inches wide),
Enduroline Series
The Enduroline Series are lapboards designed for attaching to wheelchairs. These trays are fabricated of Melamine-impregnated fiber board with a woodgrain vinyl top, and are available in tray only, tray with routed stop groove, tray with anodized aluminum rim, tray with groove and straps, and tray with rim and straps models. All models have a rectangular work surface. SIZES: All models are available in child, adult, and extra-wide sizes. DIMENSIONS (WxD): Child-size models are 20.5 x 18 inches w
Enduroline Top Drop Quik-Fit Trays (Models 33007P, 33009P, 33011P, 33019P, 33007, 33009, 33011, & 33019)
The Enduroline Top Drop Quik-Fit Trays are lap trays designed for use with wheelchairs. These trays feature a Top Drop Clamping System that enables the tray to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. The Enduroline Trays are made of melamine-impregnated fiberboard. Models 33007P, 33009P, 33013P, a
Enduroline Top Drop Quik-Fit Trays With Control Cutouts (Models 33037, 33038, 33039, 33040, 33041, 3342, 33043, 33044, 33045, 33046, 33047 & 33048)
The Enduroline Top Drop Quik-Fit Trays with Control Cutouts are lap trays designed for use with powered wheelchairs with joysticks and other controllers. These trays feature a Top Drop Clamping System that enables the tray to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. These trays also feature a cutout
Enzo Wheel
The Enzo Wheel is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This is a light weight everyday wheel. Its 5-spoke design allows the user to reach through the wheel for access under and around the chair, while its handring design allows for multiple mounting width positions. The wheel has a CNC machined aluminum hubs with 0.5-inch sealed bearings, a lightweight aluminum double wall rim, and a durable powder coated f
Epic Aluminum Hub Narrow Court Caster
The EPIC Aluminum Hub Narrow Court Caster is a wheelchair caster wheel designed for use by people with lower extremity or mobility disabilities or spinal cord injury on sports wheelchairs. This wheel has a durable, hard-rolling 1-inch narrow tread designed for court and other sport activities. The urethane tread is spun-cast from virgin base chemicals. Like a super ball, the tread bounces back when compressed to minimize energy loss and absorb vibration. The solid urethane does not absorb water
Epic Aluminum Wide Softroll Caster
The EPIC Aluminum Wide SoftRoll Caster is a wheelchair caster wheel designed for use by people with lower extremity or mobility disabilities or spinal cord injuries. These extra-wide caster wheels have wide sloping sidewalls and an arced tread. Its shape facilitates pivot and roll, as the extra girth distributes the downward pressure so the wheel maintains higher floatation and does not sink into carpet and other surfaces. Like a super ball, the tread bounces back when compressed to minimize ene
Epic Composite Hub Narrow Court Caster
The EPIC Composite Hub Narrow Court Caster is a wheelchair caster wheel designed for use by people with lower extremity or mobility disabilities or spinal cord injury on sports wheelchairs. This wheel has a durable, hard-rolling 1-inch narrow tread designed for court and other sport activities. The urethane tread is spun-cast from virgin base chemicals. Like a super ball, the tread bounces back when compressed to minimize energy loss and absorb vibration. The solid urethane does not absorb water
Epic Composite Wide Softroll Caster
The EPIC Composite Wide SoftRoll Caster is a wheelchair caster wheel designed for use by people with lower extremity or mobility disabilities or spinal cord injuries. These extra-wide caster wheels have wide sloping sidewalls and an arced tread. Its shape facilitates pivot and roll, as the extra girth distributes the downward pressure so the wheel maintains higher floatation and does not sink into carpet and other surfaces. Like a super ball the tread bounces back when compressed to minimize ene
EquaGel Wheelchair Cushion - Adjustable Protector Cushion
The EquaGel® Wheelchair Cushion - Adjustable Protector Cushion is a contoured cushion designed for individuals with mobility disabilities and lower extremity disabilities who use wheelchairs. Typically used in rehab centers and other long-term care facilities, the EquaGel® Adjustable Protector Cushion has an adjustable pelvic contour that allows for more even weight distribution and positioning, which aids in the prevention of pressure ulcers and assists in wound healing. The cushion features a
EquaGel Wheelchair Cushion - Protector Cushion
The EquaGel® Wheelchair Cushion - Protector Cushion is a contoured cushion designed for individuals with mobility disabilities and lower extremity disabilities who use wheelchairs. Typically used in rehab centers and other long-term care facilities, the EquaGel® Protector Cushion has a 0.75-inch pelvic contour that allows for more even weight distribution and positioning to aid in the prevention and treatment of pressure sores. The cushion features a fluid-resistant, vapor-permeable and flame-re
Equalizer Shooting System With Custom Chair Mount
The Equalizer Shooting System with Custom Chair Mount is a firearm support for wheelchair and a trigger adapter designed for use by people who use a wheelchair and have limited upper body movement. This system makes it possible for people with physical or neurological disabilities to hunt and shoot from their own wheelchair. The system has over 60 precision machined parts for durability and shooting accuracy, and each chair mount is custom adapted to the user's wheelchair. Multiple brackets can
Equalizer Tilt System
The Equalizer Tilt System is a powered tilt-in-space seating system designed for use by individuals with neurological or severe physical disabilities. This tilt-in-space system is designed to be mounted on a power base (not included) such as the Leisure-Lift, Inc. PaceSaver M1 powered wheelchair (see entry). CONTROLS: Integrated programmable Shark joystick controller. A swing-away controller mount and attendant control are optional. SEAT (DxW): 14 to 22 x 16 to 22; both dimensions are adjustabl
Essential Hardwood Transfer Board (Model P2300)
The Essential Hardwood Transfer Board, model P2300, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. This hardwood board is sealed and highly polished for ease in sliding and features a tapered end and one hand cut-out. DIMENSIONS (WxL): 8 x 30 inches. CAPACITY: 250 pounds.
Essential Plastic Transfer Board (Model P2301)
The Essential Plastic Transfer Board, model P2301, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. This high-impact plastic board has a smooth surface for ease in sliding and features a tapered end. DIMENSIONS (WxL): 8 x 27.5 inches. CAPACITY: 250 pounds.
Everest And Jennings Or Prc
8 inch plastic wheels supplied by customer are machined to fit rigidly mounted sealed bearings and bolted axles. Bearings need no maintenance. Modification promotes smooth running wheels. Satisfaction guaranteed.
Evoflex Pelvic Stabilizer
The Evoflex Pelvic Stabilizer is a wheelchair seat belt designed for use by individuals with lower extremity or mobility disabilities, spinal cord injury and others who use wheelchairs. The Evoflex has two parts that attach to opposing sides of a wheelchair's seat. When the user is seated in the wheelchair, the two parts attach using a push button seatbelt fastener or a Rehab Latch (available only for the medium and large sizes) to secure the user in the seat. The Evoflex's parts are semi-rigid
Evolution Back
Evolution Back is a wheelchair back support system designed for use by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury who use wheelchairs. The system is adjustable to accommodate growth and its "slide and snap" hardware is operable with one hand. It has an oversized self-inflating cushion for immersion of bony prominences, and is designed to work with lateral supports, hip belts, and hip guides. The system includes hardware with one inch of lateral a
Evolution Back Deep
Evolution Back Deep is a back support cushion designed for use by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury who use wheelchairs. It provides full posterior support and up to seven inches of lateral support. The seat can be adjusted in depth plus or minus three inches (up to 17.5 degrees of recline), and can be adjusted laterally plus or minus one inch at four points to accommodate growth or disproportionate body types. The system includes a PSIS
Expandable Tray
The Expandable Tray is a wheelchair lap tray designed for use by individuals who use wheelchairs. The wooden surface provides a large surface support for elbows and forearms, enabling better trunk support. Available with or without mounting clamps, the tray can be used on manual or powered chairs or on standing positioners, and adjusts to various widths. When not expanded, the tray fits through doorways and aisles. SIZES: Medium or large. DIMENSIONS: Each side extension adds 4.5 inches to the wi
Extended Handles
The Convaid Extended Handles are wheelchair push handle extensions designed for use by a companion or caregiver when pushing a manual wheelchair. The Extended Handles provide a more ergonomically positioned handle intended to reduce the strain on the back and wrists of tall people. They also can enhance a person's ability to maneuver a wheelchair up and down hills and stairs. The handles fit most standard, transit, and planar models of pediatric wheelchair and strollers. The extensions sold in p
Extended Width Armrest (Model 77382)
The Extended Width Armrest, model 77382, is an add-on armrest designed for with lower extremity, mobility or severe physical disabilities, spinal cord injury and others who use wheelchairs, especially those who spend extended periods of time in wheelchairs. Intended to provide a wider resting surface without increasing armrest height, this armrest accommodates individuals with upper extremity edema, flaccidity, or increased tone by decreasing the risk of slippage and damage to the arm and should
ezEnabler Tray and Cup Holder Accessory
The ezEnabler Tray and Cup Holder Accessory is designed to provide carrying capability and independence for individuals with mobility or lower impairment disabilities who use wheelchairs and walkers. The table top hook and cup-holder is lightweight, durable, portable, and gives the user an extra arm or hand to assist them with their everyday tasks and hobbies at home, school, stores, restaurants, theaters, etc.
Fastback
The Fastback is a back support cushion designed for use by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury who use wheelchairs. This air and foam flotation cushion is comprised of three densities of foam, positioned according to density to provide mild lateral support, scapular contour, and vertebral comfort and pressure relief. A valve allows the user to release more air for greater envelopment and stability. Other features include a PSIS block for l
Feeder Board Attachment.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Attachment for a wheelchair laptray, used to stabilize dishes and glasses for a user who lacks coordination. The feeder board clamps on top of a regular laptray with medium size C clamps. The dishes, cups and glasses the person uses fit into cutout holes in the board. Topview and sideview diagrams included. SKILLS REQUIRED: Woodworking. AUTHOR: Fahland, B. TITLE: Wheelchair Selection: More Than Choosing a Chair With Wheels. REF:Book: Sister Kenny Insti
Figure-8 Clamp (Models 32310 & 32310B)
The Figure-8 Clamp is a seating hardware and a mounting clamp for accessories designed for use with wheelchairs. The two-part clamp is used to attach controls, accessories, and other devices to wheelchairs. One side of the clamp accommodates .75-inch tubing and the other side accommodates 7/8 inch tubing. Deep-set cap screws are used to tighten clamp around tubing. Set screws can provide additional mounting stability. COLOR: Model 32310B comes in black. WARRANTY: The manufacturer warrants this p
Firm Grip Joystick Holder
The Firm Grip Joystick Holder was designed to allow easy use of the joystick for persons with limited or no use of one hand. Two straps hold the joystick in place, while four suction cups on the bottom of the device secure it to a flat surface in front of the computer. An optional plexiglass undersheet ($20.00) provides a workspace and assures a good hold for the suction cups. DIMENSIONS: 6 x 5 inches. WEIGHT: Less than 1 pound.
Fitness Is For Everyone.
Video exercise tapes for the physically impaired. Each 30 minute aerobic dance routine program includes a warmup period, activity period, and cool down period. Choose from sets or individual selections: Aerobics for paraplegia, quadriplegia, cerebral palsy, amputees; Strength and flexibility exercises for all types of disabilities; Aerobics for paraplegia and quadriplegia; Aerobics for Cerebral Palsy and amputees; Aerobics for paraplegia; Aerobics for quadriplegia; Aerobics for amputees; or Aero
Fixed Arm Troughs (Models 31339R, 31339L, 32339R, & 32339L)
The Fixed Arm Troughs are designed for use by individuals who use wheelchairs and have upper extremity disabilities. Available for the right or left arm, these troughs are made of heavy-duty plastic and are equipped with brackets that slide over the existing armpads. Models 31339R and 31339L are padded with Ensolite and models 32339R and 32339L are padded with imitation lambskin. COLOR: The troughs and the Ensolite padding are black. The imitation lambskin padding is natural.
Flat Foot Rest With Heel Straps
One pair of custom size slotted Kydex foot rest plates with mounting hardware and velcro heel straps. Mount to existing wheelchair footplates to increase foot placement area. Slotted for forward and back adjustment on footplate.
Flat Free
The Flat Free is a pneumatic tire designed for wheelchairs. This innertube is made of variable density air cushioned rubber and polymers. This tire is designed to maintain constant air pressure, to be impervious to heat or cold, and to not go flat. The tire has a hollow core for shock absorption. No special tools are required for mounting. SIZE: Available in all sizes.
Flat Pac (Model Wh180)
The Flat Pac WH180 is a under seat pocket designed for use by individuals who spend long periods of time in wheelchairs. This seat pocket permanently attaches to the underside of a wheelchair seat with Velcro where it is hidden for added security. The seam is stitched down the center of the bag so the chair can be folded without articles getting in the way. The Flat Pac has a pocket for keys and a double zip closure with large pull rings. DIMENSIONS (WxD): 14 x 11 inches.
Flat Top Lateral Roll Armrest
The Flat Top Lateral Roll Armrest is an add-on armrest designed for use by individuals who use wheelchairs. This armrest fits over the existing armrest and the wide foam top provides comfort for the arm while discouraging lateral leaning. The design prevents spinning of the support around the armrest and prevents shoulder elevation. A low-profile model fits hemi wheelchairs and those that have less than three inches of clearance between the top of the finger guard and the bottom of the armrest.
Flat-Proof Tire (Model Npc-Pt444)
The Flat-Proof Tire, model NPC-PT444, is a foam- core tire and wheel designed for use on power wheelchairs or scooters. The tire is made of 65 durometer rubber with American Airless soft/solid foam filling, and has a diamond lug tread for traction in any environment. The rim is two-piece stamped steel. DIMENSIONS: 10 inches in diameter x 3.5 inches wide. WEIGHT: 5 pounds.
Fleece Wheelchair Armrest Covers
The Fleece Wheelchair Armrest Covers are wheelchair armrest pads designed to prevent skin irritation. These padded fleece covers attach with Velcro. DIMENSIONS: These pads are available in 10 inches long or 14 inches long. COLOR: Natural.
Fleece Wheelchair Armrest Pouches
The Fleece Wheelchair Armrest Pouches are wheelchair armrest pads and side pouches designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury and others who use wheelchairs. The pouches are made of washable denim and feature fleece armrest covers that provide comfort and protection to elbows and wrists. The armrest pouches can be mounted over wheelchair arms with Velcro fasteners. Each pouch features a convenient storage compartment for carrying books, ma
Flex, The
The Flex is a wheel lock system designed to enable individuals with use of only one hand to lock both wheels of a wheelchair simultaneously. This device can be installed on either side of the wheelchair. It fits most manual wheelchairs with round tubing and does not interfere with the collapsing mechanism of a folding chair. WEIGHT: 1.2 pounds.
Flexi-Fit Wheelchair Gloves
Flexi-Fit Wheelchair cloves are push gloves designed for use by individuals with severe physical disabilities, spinal cord injury, or who have had strokes. Designed for individuals with limited hand function, these gloves open wide for ease in putting them on. Made from quality neoprene, these gloves have a small textured area built into the palm for added grip. SIZES: Small, medium, large, or extra large.
Flexible Mounting Arm Kit
The Flexible Mounting Arm Kit is designed to be used in conjunction with QuadStick Sip/puff mouse control products. It has one flexible arm, a Super Clamp, and a ball and socket RAM Mount adapter. A user can clamp this mount to tables and tubular surfaces such as wheelchairs. The ball and socket adapter allows adjustment of the QuadStick’s position at the end of the arm.
Flexrim
The FlexRim is a handrim designed for use by people with mobility and lower extremity disabilities and spinal cord injury and others who use wheelchairs. This rim replaces the chair’s existing handrim and adds less than five ounces to each wheel. The handrim is made of soft, high friction rubber that attaches to the push rim of the wheelchair. It molds to fit the hand, acting as a cushion and flexing to conform to the user’s hands and arms and provide shock absorption for the user’s hands as he
Flip Away Half Lap Tray (A7079, A70710, A70712 & A70713)
The Flip Away Half Lap Trays, models A707-9, A70710, A70712 and A70713, are lapboards designed for use by individuals who use wheelchairs. The easy-to-clean plastic trays secure on either the right or left side of a full-length or desk-style upholstered wheelchair arm. These trays offer comfortable support and lift up and out of the way during patient transfers or wheelchair storage. DIMENSIONS (WxD): 13 x 21 inches with a one-inch molded rim and 3.5 inch diameter recessed area for cup or glas
Flip-Up Armrest
The Flip-Up Armrest is an elevating armrest designed to be attached to 7/8 inch tubing back uprights or to a back insert. The armrests have adjustability in height and angle and swing up for transfers. The armrests do not include pads.
Folding Manual Wheelchair Cover
The Folding Manual Wheelchair Cover is a wheelchair cover designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury or other people who use wheelchairs. Designed for manual wheelchairs, this cover is weather and dust resistant and is made for travel, wheelchair lifts and storage. Features include a Velcro seam with snap buckle; a front elastic band that wraps around the footrest; a rear drawstring cinch (cord lock) that secures the cover bottom to wheels
Folding Safety Flag
The Folding Safety Flag is a safety flag designed for use on manual or powered wheelchairs or scooters. Designed to increase visibility, this penant-shaped flag has a folding shaft that enables the flag to fold below the user's head when entering and exiting vehicles or when not in use. COLOR: The flag is orange.
Folding Wheel For Wheelchair
PROTOTYPE --- PURPOSE: To create a prototype of the Crossbreed folding wheel for wheelchair users and individuals with mobility disabilities. The Crossbreed designer, Duncan Fitzsimons is developing a wheelchair-specific version of the Crossbreed with an integrated push rim and easy-to-use locking lever. The first models of this wheel are made from a carbon-fiber composite to meet the weight and stiffness requirements of the most demanding wheelchair users. This prototype is expected to be avail
Foot Board (Model S-61)
The Foot Board, model S-61, is a foot support designed for use by individuals who use wheelchairs. This foam-padded unit fastens to one footplate and rests freely on the other to bridge the gap between them and create a one-piece foot support. The support flips up for transfers.
Foot Bracket Platforms
Several styles of platforms mount to wheelchair footplates for foot positioning. Complete assembly includes one pair of bent slotted plastic platforms, two pairs of plastic side plates which mount to footplate, one pair of heel plates or stops, and one pair of velcro foot straps. Adjustable in height, depth, and angle. Available in small (3 inches wide) and medium (4 inches wide) sizes. May be ordered as complete assemblies or individual replacement parts.
Foot Harnesses (Models 2A, 2B, & 2C)
The Foot Harness is a foot pedal attachment designed to keep feet fixed in place and provide neutral foot control on surfaces such as wheelchair plates and bicycle pedals. Sold in pairs, these foot harnesses promote proper alignment and weight bearing while helping to avoid injuries to the feet. Mounting hardware is included. The harnesses have a sandal-like design (heel/ankle straps) and a plastic mounting base for snap on/off attachment to the pedals. The length and width are adjustable. SIZES
Foot Hugger (Models 6351, 6352, 6353, & 6354)
The Foot Hugger is a legrest panel designed to prevent the wheelchair user's feet from sliding off the foot plates. This foam-cushioned panel is covered in wipe-clean vinyl. This unit protects the user's legs and includes an attached extender to raise the height of the foot plates. DIMENSIONS: All models fit 18-inch wide chairs. Model 6351 is one inch high, model 6352 is two inches high, model 6353 is three inches high, and model 6354 is four inches high.
Foot Rest Boxes.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Boxes to attach to standard wheelchair footplates to maintain position of feet. Design for making wooden boxes to maintain child's feet on wheelchair footplates. Includes materials list and diagrams. SKILLS REQUIRED: Woodworking. AUTHOR: Caston, D. TITLE: Easy to Make Aids for Your Handicapped Child REF: Book: Human Horizons Series, p 126. Also available from Prentice- Hall, Englewood Cliffs, NJ. NARIC CALL NUMBER: R1798. 1981.
Foot Shields For Wheelchairs.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Bumper-like foot shield for a wheelchair to protect the feet in case of a collision. It can also be used to push a ball in some wheelchair sports. Describes a six inch high foot shield for a wheelchair made of vacuum-formed 3/16 inch high-density polyethylene and attached to the footrest with three tubes. Includes photographs and a diagram. COMMENTS: Suggests that except for the polyethylene portion the guard can be manufactured in any shop. Designed b
Foot Stool.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Small angled stool to facilitate putting on shoes and socks, tying laces or clipping toenails. Stool made of softwood, large enough to rest one or both feet on, holding the toes higher than the heels, making the feet easier to reach. Includes instructions an drawings. SKILLS REQUIRED: Woodworking. AUTHOR: Caston, D TITLE: Easy to Make Aids for Elderly People REF: London, England: Souvenir Press: p 30-31. Also available from Prentice- Hall, Englewoods C
Foot Support For Wheelchair
CUSTOM ADAPTATION PURPOSE: To enable an individual with a fused knee to have leg support in a wheelchair without creating pressure beyond the ankle. This device replicates a home footstool with the length reduced so only the ankle comes in contact with it. The unit attaches to the existing front rigging of the wheelchair and can be removed when not in use. TITLE: Wheeling Easy. JOURNAL: TAD Journal. REF: Vol. 12 no. 1, Autumn 2001: p. 16. PAGES (including cover): 2 2001.
Footboard And Brackets
One-piece ABS plastic footboard ($64). 3 sizes, 10 to 14 inches wide by 6 to 9 inches deep. Brackets ($47) attach footboard to bottom of solid seat insert. 2 size ranges, 6 to 9 inches long and 9 to 12 inches long.
Footrest Platform Tops And Bottoms
Top and bottom sections allow mounting of one-piece footplates to aluminum pans or other rigid seat panels. Removeable. Fixed or adjustable knee and ankle angles. X-style foot straps.
Footrest Receptacle And Pads
The Footrest Receptacle and Pads is a foot support made of a vacuum formed plastic shell covered with molded foam, and mounts to a standard wheelchair footrest or Otto Bock Fullcare Orthotic Seating or MOSS II systems. Each footrest receptacle ($83.75) and pad ($50.25) is ordered separately. DIMENSIONS (HxWxL): Large is 13 x 10 x 6 inches; Medium is 10 x 10 x 5 inches (outside dimensions). COLOR: Black and grey.
Footrest, Swing Tube, & Bracket
The Footrest Swing Tube and Bracket is a one piece footboard which mounts to the insert bottom to support the feet and allow the seat and footplate to move as one. Knee flexion angle may be varied from 45 to 180 degrees with mounting hardware. The Seat Mount Footrest (model 33400, $156) is made of metal. The Footrest Swing Tube (model 33422, $36) provides for the use of independent footrests and legrest cradels and still allows for insert mounting. The Pivot Bracket (model 33420, $48), Swing Tub
Fractal Machine
---- PROTOTYPE --------- PURPOSE: To design a prototype an device that attaches to a wheelchair to assist individuals with lower extremity or mobility disabilities or spinal cord injury or others who use a manual wheelchair to exercise and maintain personal fitness. The Fractal Machine is a wheelchair exercise roller designed to assist wheelchair users to participate in anaerobic and aerobic exercises. It can also be used as a training device aid a new wheelchair user to adapt to using a wheelch
Freedom Wheelchair Cup Holder
The Freedom Wheelchair Cup Holder is a wheelchair drink holder designed for use by individuals who use wheelchairs. Available for square or round tubing, this holder can also be used on scooters, walkers, rollators, and bed rails. The attached clamping mechanism tightens securely on any upright or horizontal tubing. To use, open the holder and adjust the holder's arms to hold 16- to 46-ounce cups, mugs, glasses or bottles with up to a four-inch diameter base. The holder closes flat when not in u
Freewheel Wheelchair Attachment
The Freewheel Wheelchair Attachment is an all-terrain third wheel designed for use by individuals with mobility disabilities or spinal cord injury. Once the FreeWheel is clamped to the footrest of a rigid frame wheelchair, the wheelchair user can safely traverse terrains such as grass, sand, curbs, or rough roads and walkways. For folding wheelchairs, the FreeWheel can be attached using the Folding Wheelchair Adaptor (sold separately). The FreeWheel, or FreeWheel with Adaptor, comes with everyth
Frs 3-D Fixed Position Wheelchair Mount
The FRS 3-D Fixed Position Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), the flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mou
Frs 3-D Folding Wheelchair Mount
The FRS 3-D Folding Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), this flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mount pla
Frs 3-D Swing-Away Wheelchair Mount
The FRS 3-D Swing-Away Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), this flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mount
Funbike
Funbike is a handcycle wheelchair attachment designed for use by individuals with mobility disabilities, neurological disabilities, or spinal cord injury. This unit includes a wheel and hand crank which attach to a wheelchair to convert it temporarily into a hand-propelled cycle. The unit can be attached to a fixed frame wheelchair (recommended) or to a folding wheelchair without removable footrests. The frame and most components are made of aluminum. Standard features include a 20-inch diameter
Functional Forms Wheelchair Easel / Lap Tray
The Functional Forms Wheelchair Easel/Lap Tray is designed to provide a lightweight alternative to traditional lap trays for wheelchair users. Features include a built-in 20-degree angle, pencil holder/wrist rest, removable carrying strap, magnetic paper holder, and a hidden zippered pouch. This easel also has a water-resistant vinyl or leather covering. WEIGHT: 1 pound.
Fusion 16 Wheel
The Fusion 16 Wheel is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This wheel for everyday chairs has 16 12-gauge stainless steel spokes with a lacing pattern. The wheel is lightweight with a double wall rim, a custom forged and machined fusion hub, and sealed cartridge bearings. The hub and rim are anodized. This unit is compatible with a standard 6-tab hand-ring (not included). DIMENSIONS: Available with 24, 25
G-100+ Custom Built Cushion
The G-100+ Custom Built Cushion is an alternating air pressure flotation seat cushion designed to prevent pressure sores for people with lower extremity or mobility disabilities, spinal cord injury and others who use a wheelchair. This system features computer controlled pressure management that increases and decreases air pressure in the cushion as needed. Each cushion is custom built to fit the user and wheelchair. POWER: Uses rechargeable nickel metal hydride batteries with a life expectancy
Gel Gloves (Model Vgb500)
Gel Gloves, model VGB500, are push gloves for manual wheelchair users. The gloves have polymer gel inserts in the palms to provide maximum impact absorption from harmful shocks and vibrations. The half-finger gloves are made of drum-dyed leather, terry cloth, and lycra with velcro closures on the backs of the wrists. SIZES: Small, medium, large, extra large, extra extra large. COLOR: Black palms with two-tone blue backs.
Gel Ovations Arm Pads
The Gel Ovations Arm Pads are wheelchair armrest pads designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. These pads are designed to provide comfort and protection to elbows and wrists, help prevent pressure sores or ulcers, and aid in healing of existing sores or abrasions. These pads come in a variety of sizes and have T-nut spacing to allow installation on most armrests without the need for modifications. DIMENSI
Gel Ovations Knee Buttons
The Gel Ovations Knee Buttons are knee protectors designed to prevent skin breakdown due to contact with metal legrest hardware. Sold in pairs, these gel protectors are available for manual fixed frame and elevating legrests. DIMENSIONS: 4.5 inches in diameter; 1.25 inches deep.
Gloves For Life
Gloves for Life are push gloves designed for use by individuals with quadriplegia, paraplegia, or others with limited dexterity. Custom made of suede with rubber palm inserts, these gloves are designed to make wheelchair wheeling less strenuous. The palms of the gloves are applied to the rims of the wheelchair wheels to aid in propelling and braking the chair. Rubber palm pads prevent heat and friction, helping protect the skin of the palms. A D-Ring is attached to a hook-n-loop strap for a secu
Greenmont's EasyPushbar
Greenmont's EasyPushbar is a wheelchair pushbar that attaches to a wheelchair hand grips, raising the height 4 inches to approximately the height of a standard shopping cart. The EasyPushbar allows the caregiver to stand straighter, have better control, reduce neck, shoulder, back and wrist strain, make easier curb and ramp maneuvers. It is fully adjustable from 15.5 inches to 24 inches to fit most manual wheelchairs. The EasyPushbar can also be removed to allow for folding or storage of the whe
Ground Fx! Lighting Kit
The Ground FX! Lighting Kit is a wheelchair light designed for decorative illumination of a wheelchair. The kit provides colored light under the wheelchair, with fun lighting effects that make the chair glow in a chosen color. The Kit contains 3 IllumiRay Mini lights. Each light has a 12-element circular LED array that emits a brilliant 35 degree cone of light with an output is 8200 MFC. The emitted beam helps the user to operate a wheelchair safely at night. Each light has an anodized aluminum
Gyroset
---- PROTOTYPE --------- PURPOSE: To create a prototype a wireless headset wheelchair control system for individuals with severe disabilities and/or quadriplegia. Individuals who are paralyzed from the neck down have a limited number of options to control their wheelchairs (i.e., joysticks, sip and puff tubes). Márton Juhász and Now Technologies, a Hungarian firm, have developed the GyroSet, an Android tablet-powered system that allows a person to use head movements to guide a powered wheelchair
H-18 Magic Arm
The H-18 Magic Arm is a mounting kit for tablet computers, communicators, or ebooks, an adjustable ebook holder and a stand for a tablet computer designed for use by people with grasping, neurological or upper extremity disabilities, cerebral palsy or arthritis. The H-18 includes the Super-Clamp which allows clamping to wheelchairs, bedrails, desks or tables; and an iPad tablet holder without case or an adjustable tablet holder (ATH) for other devices or tablets such as the Auggie or Super-Auggi
H-57 Mini-Arm For All Ipads
The H-57 Mini-Arm is a stand for tablet computer designed for use by individuals with use of one hand, grasping or upper extremity disabilities, or arthritis. The H-57 is designed for use with the Apple iPad and other tablets. It includes the Super-Clamp (which allows clamping to wheelchairs, bedrails, desks or tables) and an iPad tablet holder without a case or an adjustable tablet holder (ATH). The user can select a standard, tall, or tall and wide ATH. The tablet can be removed from the holde
H-80 Short Arm
The H-80 Short Arm is stand for tablet computer and an adjustable ebook holder designed for use by people with grasping, neurological or upper extremity disabilities, cerebral palsy or arthritis. The H-80 includes the Super-Clamp (which allows clamping to wheelchairs, bedrails, desks or tables) and an iPad tablet holder without case or an adjustable tablet holder (ATH) for other devices/tablets such as Auggie/Super-Auggie (see separate entries), Barnes and Noble Nook, and Amazon Kindle. The user
H-92 Phone Holder
The H-92 Phone Holder is a cell phone holder and tablet computer mounting system designed for use by individuals with upper or lower extremity, grasping and mobility disabilities, individuals with use of one hand, and wheelchair users. The Phone Holder’s gel case attaches to the “Quick Connect” lever which screws into the end of a Short, Mini, Articulating, Magic Arm or Super Clamp (see separate entries). The screw size is 1/4-20. The Phone Holder expands from 1.625 to 4.5 inches. The “Quick-Con
Halo Strap
Soft velcro strap with mounting hardware and D-ring closure. Mounts to headrest system by attaching to lateral headrest pads. Cloth lining available on request.
Hand Rims With Knobs (Model 41)
The Hand Rims with Knobs, model 41, are handrim projection knob units designed for use by individuals who are unable to grasp standard pushrims. These units feature chriome-plated handrims with 6 large, plastic projecting knobs attached. The knobs the assist the user with wheelchair propulsion.
Hand Rims With Projections (Model 42)
Hand Rims with Projections, model 42, are vertical handrim projections designed for use by individuals who are unable to grasp standard wheelchair pushrims. The unit features a chrome-plated pushrim with 8 rubber-covered vertical projections.
Hangin Out Bag (Model 160)
The Hangin Out Bag, model 160, is a wheelchair backpack or carrying bag for walker designed for use by individuals with walking or mobility disabilities. Available in cordura nylon or heavy denim, this bag is equipped with wide patterned or solid polyester webbing with black plastic side release buckle belt for hanging from U-shaped handles, wide armrests, walkers, or chairs that have no push handles. A top bag flap is also featured for monogramming. Other features include a single inner compart
Hard Anodized Handrim
The Hard Anodized Hand Rim is a wheelchair hand rim designed for use by manual wheelchair users with lower extremity or mobility disabilities or spinal cord injury. This is a long life lightweight alloy hand rim that fits 24-inch Quickie and Magic wheels that are standard on many wheelchairs. It provides a smooth hard surface to push with and its hard anodized coating allows heat to dissipate rapidly so the user's hands do not burn going downhill. The unit is attached by 6 rivnuts.
Hardwood Transfer Boards
Hardwood Transfer Boards are designed for individuals with mobility disabilities to transfer from their wheelchair to a bed, chair, toilet, etc. Made of solid, smooth-finish. Tapered ends for easy use.
Haseltine Flyer (Model 504-C)
The Haseltine Flyer, model 504-C, is a wheelchair carrier designed to protect powered wheelchairs during airline travel. The two-piece carrier shell is rotationally molded of recyclable polyethylene and lined with foam padding. The chair is secured to the base piece which has a lip around it to prevent slipping during transit. An internal strapping system holds the chair and its accessories in place. The second piece of the carrier covers the chair and is fastened to the base. The carrier also f
Haseltine Roosevelt Flyer (Model 504-A)
The Haseltine Roosevelt Flyer, model 504-A, is a wheelchair carrier designed to protect folding manual wheelchairs during airline travel. The carrier shell is rotationally molded of recyclable polyethylene and lined with foam padding. An internal strapping system holds the chair and its accessories in place. The container is held closed by six Velcro straps threaded through a footman holder. An additional footman's loop can accommodate an airline luggage tag. The carrier also features an in-mold
Hatch Gloves
Hatch Gloves are push gloves designed for use by individuals who use wheelchairs. These gloves have genuine leather palms and cotton crocheted mesh backs, with half thumbs and fingers. SIZES: Extra-small, small, medium, large, extra-large, and extra- extra-large. COLORS: Tan or black.
Hatch Para Glove (Pair)
The Hatch Para Glove (Pair) is designed for use by individuals who use wheelchairs. This glove has been especially designed for paraplegics. It is made from heavy-duty drum-dyed cowhide. It has a full thumb and reinforcement between the thumb and index finger for added support and protection. Available in Black only.
Hatch Quad Glove (Pair)
The Hatch Quad Glove (Pair) is designed for use by individuals who use wheelchairs. The gloves are designed with two separate velcro straps close securely and comfortably at a perfect fit. The protection of Hatch Quad Push Wheelchair Gloves does not end with the hand and wrist. These wheelchair gloves extend beyond the wrist and are padded in all of the critical areas to prevent friction burns and nerve irritation. Wheelchair gloves are made of quality leather and spandex.
Hatch Quad Gloves w/ Rubber Palms (Pair)
The Hatch Quad Gloves w/ Rubber Palms (Pair) is designed for use by individuals who use wheelchairs. These Hatch Gloves' palms improves both pushing durability and hand protection while increasing traction as well. The globes come in the standard range of sizes (A, B and C).
Have-A-Tray Carrier (Models 70612-3200/3400/6100)
The Have-A-Tray Carriers are caddys for wheelchairs, walkers, and crutches. The two-compartment carriers allow ready access to personal itms. The caddies are made of molded polypropylene copolymer with a drain hole in each compartment. Hardware is supplied with each model for proper attachment. DIMENSIONS: Inside dimensions are 11.25 x 2 7/8 x 7.75 inches. WEIGHT: Wheelchair carrier (70612-6100) is 2 pounds, walker caddy (70612-3200) is 1.3 pounds, and the crutch caddy (70612-3400) is 1.3 pounds
Headrest Swing Away Bracket (Sm-Hrsa240)
The Headrest Swing Away Bracket, model SM-HRSA240, is switch mounting hardware designed for use by individuals who use wheelchair headrests. This arm attaches to any Stealth or Otto Bock style headrest (see entries). It is made ready to mount an egg switch or a sensor in a spot pad. Once adjusted in place the user can swing it away when it is not needed and push it back to the same spot when needed.
Headsup Flexible Head Support System
HeadsUp is a head support designed for use by children and adults with neurological or severe physical disabilities or spinal cord injury. This support consists of a hat and flexible elastic bands that fasten around a wheelchair headrest or high seat or chair back to hold the head up. Each side adjusts independently from the other, creating the ability to apply the desired amount of tension. As the elastic stretches, it allows a full range of motion;as the elastic stretches, the resistance incre
Heel Loop (Model 83)
The Heel Loop, model 83, attaches to pegs at back of wheelchair footplates help to prevent the user's foot from slipping off footplate. The loop is fabricated of webbing. DIMENSIONS: 2 inches wide.
Heel Loop Flipper
Heel loop flipper automatically flips wheelchair heel loops out of the way when the footrest is turned up. The flipper slips over the footrest hanger tube and locks with one twist. The coil shaped device slips over the tube, with a finger extended out behind the heel loop so that it is guided into a fold. Does not work with naugahyde covered heel loops or with elevating legrests. Works with most models or wheelchairs.
Hi D Transfer Board (Model Bk6111)
The Hi D Transfer Board, model BK611, is a transfer board designed for use by individuals with mobility disabilities. Made of polyethylene plastic, this transfer board features a smooth easy slide surface with round corners and centered hand slot. DIMENSIONS (LxWxD): 26 x 10 x .5 inches. WEIGHT: 6 pounds.
High Quad Gun Mount (HQ100)
The High Quad Gun Mount, model HQ100, is a rifle, shotgun, pistol and crossbow support and trigger activator designed for use by people with severe physical or upper extremity disabilities or spinal cord injury who use a power wheelchair. Intended to make hunting accessible to individuals with no use of the upper extremities, this device is based on a mounting plate placed under the wheelchair’s seat cushion before the user transfers into the chair. Once the user is seated in the wheelchair, a v
Hill Holders
Hill Holders are incline holders designed to prevent roll back on hills or ramps when a wheelchair user changes grip on the handrim or rests. These wheelchair attachments are easily engaged or disengaged, and do not require finger dexterity. These wheel locks fit most wheelchairs with removable arms.
Hip Belt
Black nylon webbing belt, padded or nonpadded. 72 inches long by 1, 1 1/ 2, or 2 inches wide. Side release, pushbutton, or lever release buckles. Mounting bands to fit 7/8 or 1 inch tubing available.
Hip Belts (Model Ee 3C/103-5000)
Wheelchair seat belt. Nylin webbing and plastic delrin buckle. Has a pair of iliac crest relief pads so that the belt may be cinched tightly without causing pressure on the bony prominences. Should be mounted at a 45í angle to the seat.
Hip Pocket
Wheelchair side pouch attaches to armrest with velcro straps. Cordura nylon. Hip pocket measures 10 1/2 inches long, 6 inches wide and 2 inches deep. Inside compartment with zipper closure. Colors: black, red, navy, royal blue, tan, brown, and light or dark gray.
Hip Strap
Velcro strap with mounting hardware and D-ring or buckle closure. Mounts to back of solid back or underside of solid seat.
Hover Mounting Kit For Idevices
Hover Mounting Kit for iDevices is a mounting system designed to mount iDevices (i.e. iPads, iPad mini, iPhone 4, 4S or 5, etc.) using the Latitude Mounting Arm. It is designed for use by individuals with limited upper extremity coordination and strength, fine motor and grasping difficulties. This kit includes the Latitude Mounting Arm, Super Clamp, mounting plates and a Quick Start Guide. It is made out of strong carbon fiber. WEIGHT: 1.1 lbs/.5kg COLOR: Black WARRANTY/GUARANTEE: As stated by t
Hubscrub (Model 20 / 30)
The HUBSCRUB, model 20/30 is wheelchair cleaning system designed to clean, sanitize, and disinfect wheelchairs and other durable medical equipment. The system is housed in an aluminum cabinet with a door on the front. Within the cabinet are recessed, moving nozzles that spray hot (110 degrees Fahrenheit) water provided by a 1 horsepower wash pump. Water drains into a stainless steel internal sink from which water is pumped out by a .33 horsepower drain pump through a raised drain line two to thr
Hubscrub (Model 20 / 50)
The HUBSCRUB, model 20/50, is wheelchair cleaning system designed to clean, sanitize, and disinfect wheelchairs and other durable medical equipment. The system is housed in an aluminum cabinet with a door on the front. Within the cabinet are recessed, moving nozzles that spray hot (110 degrees Fahrenheit) water provided by a 1 horsepower wash pump. Water drains into a stainless steel internal sink from which water is pumped out by a .33 horsepower drain pump through a raised drain line two to th
I Back (Model H)
Modification for any Freedom Designs solid back insert, 1/2 inch marine grade plywood, 1 1/2 inches of foam padding, naugahyde upholstery. Cut in the shape of a capital letter-I+ so that trunk supports are at the trunk and adjustable the length of the center section. Can be used with any hardware.
Iadapter Device Adapter
This device adapter is meant to attach iPads or other tablet devices to wheelchairs. It is meant to work with the RJ Cooper & Associates' Magic Arm, Articulating Arm and Mini-Arm. The adapter attaches to the back of the iPad or tablet with heavy-duty Velcro.
Illumiray Lighting System
The IllumiRay Lighting System is a wheelchair light designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury and others who use a manual wheelchair. The system includes 2 white Solid State Mini Lights, 2 red Solid State Mini Lights, a Black Jack switch and a wiring harness. Each light has a 12-element circular LED array that emits a brilliant 35 degree cone of light with an output is 8200 MFC. The emitted beam helps the user to operate a wheelchair safe
In Your Face Viewbase
The In Your Face Viewbase is a mounting kit for smartphones and other handheld devices that can be used by individuals with upper extremity or grasping disabilities. The unit consists of a flexible gooseneck with a lower clamp for attaching to a table, wheelchair, plane tray, or other support, and an upper clamp for holding the device. The top clamp is spring-loaded, allowing the smartphone to be inserted and removed. The clamp provides a padded and secure tight grip that fits all iPhone and iPo
Incrediback Moldable Reclining Back System
The IncrediBack Moldable Reclining Back System is a reclining wheelchair conversion designed for use by individuals with mobility disabilities. This system transforms a standard wheelchair to a reclining wheelchair and can be molded to accommodate kyphosis, scoliosis, and other spinal curvatures. The supports can be remolded as the user's needs change. The unit attaches easily to most chairs, reclines up to 20 degrees, and folds with the wheelchair. SIZES: Standard and tall. DIMENSIONS (WxH): T
Incrediback Rigid Reclining Back System
The IncrediBack Rigid Reclining Back System is a reclining wheelchair conversion designed for use by individuals with mobility disabilities. This system transforms a standard wheelchair to a reclining wheelchair and is designed for use by individuals without spinal curvatures who require relief from forward or lateral leaning or who rquire additional comfort. The unit attaches easily to most chairs and reclines up to 20 degrees. The tall modesl include a moldable headrest above the rigid shell.
Incredihugger Wheelchair Back
The IncrediHugger Wheelchair Back is a wheelchair back support designed for use by wheelchair users with cerebral palsy, neurological disabilities, scoliosis, or upper extremity disabilities. This replacement back can be custom molded to fit the user's body contours. Its lateral supports help discourage side leaning, and its seat recline of up to 30 degrees discourages front sliding. The back has four inches of height adjustment, and may be folded with the wheelchair. The back comes in a standar
Independence Mount With Notebook Plate
The Independence Mount with Notebook Plate is a wheelchair mounting kit for communicators and portable computers. Designed to be mounted on the right or left side of the wheelchair, this unit fits most communicators and portable computers and can be adjusted to hold the device at the right height, position, and angle for comfortable operation. This mount can be easily folded out of the way when not in use.
Independent Wheelchair Assistant (IWA)
---- PROTOTYPE --------- PURPOSE: To design a prototype of an electric power assist unit for a manual wheelchair for individuals with lower extremity or mobility disabilities or spinal cord injury so they can independently access their local communities safely and easily. The Independent Wheelchair Assistant (IWA) design utilizes the user’s own wheelchair, acting as a true assistant and eliminating the need to constantly transfer between other devices like scooters or power chairs. The user atta
Independent Wheelchair Assistant (IWA)
The Independent Wheelchair Assistant (IWA) is a device to help wheelchair user's who constantly need to transfer from one device to another. The design utilizes the user’s own wheelchair, acting as a true assistant and eliminating the need to constantly transfer between other devices like scooters or power chairs. The user attaches to the device from the rear via a small bracket that must be attached to the wheelchair. The bracket slides into the back of the IWA, lifting the two front caster whe
Individual Footrest And Tops
Footrest tops ($295 per pair) allow adjustment of knee angle. Anterior-posterior adjustment. Removeable hardware attaches to aluminum pans or other rigid seat panels. Bottom of tube has clamp to allow use of standard footrest L-bars. Footrest bottoms ($185 per pair) have flip-up footplate with heel loop. Small for 12 and 14 inch chairs, large for 16 and 18 inch chairs.
Inglis Drink-Aide
The Inglis Drink-Aide is a cup with holder designed for use by individuals who use wheelchairs or who have limited upper body movement. Designed to enable independent hands-free drinking, this unit consists of a 28-ounce insulated water bottle; a long flexible, vibration-resistant drinking tube; and a universal clamp. The clamp enables the unit to be attached to a bed, a wheelchair, etc. OPTIONS: Extra drinking tubes.
Innerthanes
Foam core tires for all three and four wheel wheelchair alternatives. Core of Endurothane is molded inside tire to conform to tire and rim. Never goes flat. Bolt two piece rim together and install.
Intelliwheels Easy Push
The IntelliWheels Easy Push is a two-gear wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This wheel's handrim is connected directly to a gearbox in the wheel's hub. When the user pushes on the tire, the wheel engages the standard 1:1 gear ratio, but when he or she pushes on the handrim, the gearbox engages a 2:1 gear ratio that requires half the effort of standard pushing for activities such as rolling through deep pile carpe
Interface Hardware
The Interface Hardware is headrest accessory hardware for the Occipital "T" Bar designed for positioning an occipital bar on a wheelchair. The Interface attaches to the rear of the occipital bar. DIMENSIONS: The swivel tubes are available in 4-, 6-, or 10-inch lengths. The "T" tubes are available in 4- or 6 inch lengths. COLOR: Available in black and stainless steel.
Invacare Reliant Linak Battery Pack (Model 1078276)
The Invacare Reliant Linak Battery Pack (Model 1078276) is designed for users who use powered wheelchairs, to be used with Reliant Power Lifts. The design features anti-entrapment that stops motion is the boom meets resistance while lowering. The battery pack can be exchanged of mounted on the charger and/or the control box using Linak mounting brackets. The battery pack beeps when the battery needs to be recharged and required one 24-volt battery. Charger used for this battery is available sepa
Invisible Wheelchair Lap Tray (Model 606303)
The Invisible Wheelchair Lap Tray is a clear plastic lapboard designed for use with wheelchairs. Fittings include T-bars, rubber belt fastening straps, and foam padding to protect armrests. The unit fits most standard arm wheelchairs. DIMENSIONS: 22.75 x 22 3/8 inches.
Inyo Heavy Duty Wheelchair Tire, The
The Inyo Heavy Duty Wheelchair Tire is a replacement rubber wheelchair tire designed for use by wheelchair users. This heavy-duty tire is designed for use on high profile rims and has a smooth, non-marking tread pattern. The tire is designed to provide super grip on slick surfaces. DIMENSIONS: 24 x 1 3/8 inches.
Inyo Wheelchair Tire, The
The Air Free Inyo Wheelchair Tire is a replacement rubber wheelchair tire designed for use by wheelchair users. This super-grip tire is designed to be used on high profile rims and has a non-marking tread pattern. DIMENSIONS: 24 x 1 3/8 inches; this tire also fits many 24 x 1.25 inch wheels.
Ipad Mount
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a customized iPad mount for an electric wheelchair for individuals with mobility disabilities and spinal cord injuries, including people with quadriplegia. A quadriplegic used a computer to organize his activities such as painting, filmmaking, counseling, and motivational speaking. Laptops do not easily mount onto the electric wheelchair, and when the iPad became available, this individual jumped at the chance. Working with TADNSW an iPad b
Ipad Mounting System (Model 1556)
The iPad Mounting System, model 1556, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system is composed of three parts: a mounting platform for the iPad, a mounting arm, and a clamp. Two flexible cords that securely hold the iPad to the platform are included. The light duty mounting arm expands from 14.5 inches to 24 inch
Iv (Intravenous) Rod And Holder (Model 95)
The IV (Intravenous) Rod and Holder is designed for use with most wheelchairs. This device mounts to a wheelchair back and extends up to hold IV bottles. DIMENSIONS: The maximum extension height is 30 inches.
Jay Active Back (Models 520, 522, 525, 527 & 528)
The Jay Active Back, models 520/522/525/527 & 528, is a back support cushion designed to provide comfort and stability for chair users. This contoured support cushion is composed of lightweight materials and features adjustable height and back angles designed to help relieve back pain. It also includes an "Air Exchange" cover designed to reduce perspiration and heat buildup. With a rigid back shell, this support cushion is not intended to bow or stretch. DIMENSIONS: All models feature adjust
Jay Adjustable Solid Seat
The Jay Adjustable Solid Seat is a solid seat insert designed to improve posture by providing a firm, fully-adjustable base of support. The seat is adjustable in height, width, depth, and angle to allow an immediate fit and future change, when needed. The seat is made of rib-reinforced urethane and has an anti-slide surface so that cushions will not shift. The seat insert is designed to fit all wheelchairs; the universal cross-bar cut-out allows dropping the seat depth on virtually all wheelchai
JAY Foot Box
The JAY Foot Box is designed to protect the lower extremities from injury and skin breakdown resulting from periods of high tone. It offers wheelchair support for foot, ankle, and calf skin protection and comfort. The foot box offers three styles to suit individual client needs. Foot Boxes reduce the risk of skin breakdown and/or client injury that may result from periods of high tone or continual contact with the hangers and foot plates.
Jay Modular Back
The Jay Modular Back is a solid back insert made of aluminum that will accommodate either a Jay Custom Contoured Insert to fit deformities, or a Jay Standard Insert. The aluminum shell includes recline and depth adjustment, foam side guards, and clamp-on hardware. The Custom Contoured Insert includes a foam back with shim, full-width fluid pad, and an AirExchange cover. The Standard Insert includes a foam back with a spinal fluid pad and AirExchange cover. DIMENSIONS: Back shell is available in
Jazz Backpack
The Jazz Backpack is designed for use by wheelchais users with mobility or lower extremity disabilities or spinal cord injury. The large capacity main compartment has room for bulky items such as jacket and notebooks. It features a large front zippered pocket that is divided into two roomy compartments. Also features a foam-lined back and semi-rigid top that helps hold its shape so it’s easier to get things in and out. It is designed to hang on the seatback or push handles using web straps that
Joybar
The JoyBar is a powered wheelchair controller designed to enable powered wheelchairs to be controlled using T-bar scooter-style operation. The ReBar utilizes a Center Drive System that consists of mounting hardware and a socket that can be mounted in three positions: in front of the seat on the center line; on the side beneath either armrest; or in the back of the wheelchair. When mounted on the side, the mast with the controller can be placed there to facilitate transfers or better access to de
Joystick (& Mouse) Trainer
The Joystick (& Mouse) Trainer is a wheelchair control switch assessment program designed to enable users to learn the skills necessary to operate a powered wheelchair without the risks associated with operating the chair itself. This program begins at a very early motor and cognitive level with simple exploratory activities for gross movement and cognitive awareness, moves through initial proportional path-oriented tasks, and graduates to maze games for fine control. As the user's skill le
Joystick (Model 3185)
A proportional type joystick used for mdoe selection and operation of a Dufco Multimode Interface. During wheelchair operation, this joystick provides precise control of both speed and direction. May be configured with a chin-cup for chin oeration, or a knob for hand operation.
Joystick (Model 3345)
An 8-direction, heavy duty, multiple switch actuator used for mode selection and operation of a Multimode Interface. Requires moderate operating pressure and is intended for hand operation by those with average strength.
Joystick (Model 3361)
An 8-direction, short throw, multiple switch actuator used for mode selection and oepration of a Multimode Interface. Requires moderate operating pressure and is intended for those with average strength. May be reconfigured with either a knob or chin-cup.
Juni Hi Lo Base
This chair base is equipped with a gas strut to make adjusting the chair to 22.5" in height easier. The slimline footprint makes this the ideal chair to fit under most classroom desks.
The Juni Hi Lo Base has been designed with both the carer and child in mind. The adjustable push handle and lockable castors aid maneuverability. The adjustable footrest provide stability for the child’s feet. The Hi Lo Base is only available for the size 1 & 2 Juni chair. The mobile base and push handle hav
Just-A-Sac Wheelchair Bag
The Just-A-Sac Wheelchair Bag is a wheelchair back pouch designed for use by individuals who use wheelchairs. The pouch has one large, open-top pocket and attached loops slip over the wheelchair push handles. DIMENSIONS (WxH): 14 x 11 inches.
K-Special Back
The K-Special Back is a wheelchair back support designed for use by individuals with mild to moderate kyphosis and/or weakness of the trunk. This padded fabric back replaces the standard wheelchair upholstery, has a smooth surface, and is shaped to accommodate and support the user's entire back, eliminating pressure from the apex of the curve and providing lateral support. This back is available in slip-on or screw-on styles to accommodate most wheelchairs. Folding wheelchairs can be folded with
Kangapouch (Model 977)
The Kangapouch, model 977, is a wheelchair and walker caddy designed to afford people with mobility disabilities the ability to carry items with them. Made of corduroy, the Kangapouch features oversized, deep pockets and attaches to the front of a walker or the back of a wheelchair using Velcro straps. DIMENSIONS (LxW): 19 x 16.5 inches. COLOR: Assorted. WARRANTY: The manufacturer guarantees satisfaction with this product or it may be exchanged or returned for a full refund.
Katalavox
Katalavox is a voice input powered wheelchair controller that enables the user to control the movements of the chair by voice commands. Combinations of voice commands allow the wheelchair to take up to 84 driving positions including 4 forward speeds, 2 backward speeds, and 4 angles to the right or left. Commands can be given in any language.
Keyhole Back
The Key-Hole Back Support is a wheelchair back support designed for use by individuals with spinal curvature and other back disabilities. This back supports the user in an upright position, enhancing posture, visual field, respiratory function, balance and trunk support. The unit conforms to the individual body shape and a stretch fabric panel adjusts automatically to the severity of kyphosis, ensuring a custom fit. The user can change positions without sacrificing general support. Split back co
Kimba Neo with Leckey Mygo Seating
Kimba Neo with Leckey Mygo Seating is a stroller and pediatric mobility system designed for use by children with limited upper and lower extremity strength and coordination. The Mygo seating and the Kimba Neo Mobility base are one unit. This mobility base is designed for indoor/outdoor usage, and features a more rugged base than most primarily indoor bases. The seating by Leckey, called Mygo, can be used with other bases and is adjustable.
Kool-Brella
Umbrella, nylon taffeta. Waterproof. Sun reflective due to aluminum-based top-side coating. This automatic opening umbrella has a wooden shaft and handle with a double canopy and Velcro closure straps on both canopies. DIMENSIONS: 48 inch arc. WEIGHT: Less than 2 pounds.
Labac Mounting Kit (Model 3515)
Used for mounting a head operated actuator to the back of a Labac recliner. The mounting kit consists of a mounting bar with a stop clamp, a C-mounting rod, and a rod clamp to join the mounting rod to the mounting bar. Permits the actuator to be removed from the recliner, and returned to its original position without the need to readjust the mounting.
Lap Hugger (Models 6515, 6515M, & 6515N)
The Lap Hugger is a torso support designed to prevent forward leaning by people who use wheelchairs. This soft lap cushion fits between the wheelchair user and the wheelchair frame and also provides arm support. The standard model have notches to fit around the armrest posts. Model 6515N is narrower for easier removal. Both styles have a wipe-clean vinyl cover. DIMENSIONS: Both styles fit 16- to 18-inch wide wheelchairs. The standard model is 4 inches thick. COLOR: Model 6515 is blue and model 6
Lap King Wheelchair Lap Desk
The Lap King Wheelchair Lap Desk is a wheelchair lap tray designed for use by wheelchair users. The Lap King is constructed of a two-sided detachable lap tray made of ABS plastic that is attached to a U-shaped microbead fill cushion. The lap tray is reversible with one side having a flat surface on which the user can write, read or eat; and the other side has a dimpled surface that allows the heat generated by a laptop computer to disperse and the computer to remain cool. Both sides of the lap
Lap Pal With Nylex Cover (Models Msc019038, Msc019037, Msc019032, Msc019035, Msc019030, & Msc019036)
The Lap Pal with Nylex Cover is a lapboard designed for use as a wandering patient system for wheelchair users with Alzheimer's disease or cognitive disabilties. This safety cushion fits snugly across the user's lap and securely against the wheelchair's arms, helping to keep the user from sliding down or getting out of the chair unassisted. The cushion is made of durable, lightweight polyurethane foam covered with Nylex fabric, and provides a resting place for user's arms. The cushion is flame-r
Lap Top Cushion (Series 307010 Through 307014 & 307030 Through 307034)
The Lap Top Cushion is a lap tray designed to provide individuals who use wheelchairs with proper positioning and a work surface. Covered in durable, liquid-proof vinyl, these polyfoam-padded cushions serve as an armrest, a means of carrying personal items, a work surface, and a tool for promoting a more upright sitting posture. Available in three thicknesses, models are offered for wheelchairs with full- or desk-length arms and fit across the user's lap under the chair's armrests. The models fo
Lap Top Tray (Models 8220 & 8221)
The Lap Top Tray is a lap tray designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs or remain seated for long periods of time. These trays prevent forward leaning and provide elbow and arm support, while providing an activity surface. Model 8221 is padded for extra support and to reduce the risk of pressure sores. Model 8220 is clear to promote body awareness. Both models secure to the wheelchair with Velcro straps. DI
Lap Tray
The Lap Tray is designed for use by individuals who use wheelchairs. This waterproof tray has rounded corners, is melamine impregnated for durability, and sealed on both the top and bottom. A depressed edge prevents small objects from rolling off. DIMENSIONS: 23.5 x 22 inches with an abdominal cutout of 15.5 inches wide. COLOR: Woodgrain.
Lapboard.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Provides an attached table surface for a person in a wheelchair, can be used for activities or for arm support. Diagrams and suggested materials for trays; suggested variations include raised edging to keep articles from slipping off board, holes cut in board to stabilize dishes or other items. SKILLS REQUIRED: Woodworking. AUTHOR: Fahland, B. TITLE: Wheelchair Selection: More Than Choosing a Chair With Wheels. REF:Book: Sister Kenny Institute, Minneap
Lapboard.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Lapboard for wheelchair to make it easier to carry items. Instructions are provided on how to properly measure a lapboard for use with a wheelchair. Includes drawing. SKILLS REQUIRED: Woodworking. AUTHOR: Occupational Therapy Service. TITLE: REF: Resource Sheet: Institute of Physical Medicine and Rehabilitation, New York. .
Laplander
The Laplander is a lap tray designed for use by individuals with upper extremity or mobility disabilities. This portable desk has a solid work surface with rounded corners, a cut-out oval handle, and cloth elastic straps to hold materials in place. The base is a cushion made of breathable Neoprene. OPTIONS: Laplighter clip-on light with a flexible gooseneck and replacement straps. DIMENSIONS (WxDxH): 23 x 15.75 x 2.5 inches. COLOR: Natural cherry with a cream cushion or dark cherry with a black
Lapp Topper
The Lapp Topper is a lap tray designed to provide a work or feeding surface for individuals who use wheelchairs. This unit is a portable table that stays steady when placed on the lap. This tray is made of lightweight polystyrene-filledleatherette vinyl, allowing it to contour to the user’s lap. The cup holder and tray surface are made of polypropylene with a removable non-skid mat. The cup holder can be reversed for left- or right-handed use. DIMENSIONS (HxDxW): 16 x 23 x 5 inches.
Laptop Computer Tray
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To provide a customized laptop computer tray for a student with disabilities. The adaptation mounts a laptop computer (with speech software) on a standard wheelchair tray so that the screen is in view while the computer is housed under the tray and the tray surface is left free. Hardware from a standard roll out "under the desk" keyboard shelf was modified to provide a platform for the laptop. Only the switch driving the software is exposed on the tr
Large And Tall Power Wheelchair Cover
The Large and Tall Power Wheelchair Cover is a wheelchair cover designed for use by tall individuals who use power wheelchairs. This waterproof cover is designed to fit wheelchairs with high seat backs, and it can fit small and medium chairs. It is available in light weight or heavy duty material. DIMENSIONS (HxLxW): 48 x 44 x 23 inches. The circumference is 124 inches. COLOR: Black
Large Cup Holder With Round Wheelchair Attachment
The Large Cupholder with Round Wheelchair Attachment is a wheelchair cup holder with attachment designed for use by individuals with lower extremity and mobility disabilities, spinal cord injury and others who use wheelchairs. Designed for round tube wheelchair frames, this device attaches to either side of the chair and secures to wheelchair's metal frame. To open the attachment door, the user folds the door down to form the base of the cup holder, and adjusts the arms to accommodate 16-ounce t
Large Cupholder With Square Wheelchair Attachment
The Large Cupholder with Square Wheelchair Attachment is a wheelchair cup holder with attachment designed for use by individuals with lower extremity and mobility disabilities, spinal cord injury and others who use wheelchairs. Designed for square tube wheelchair frames, this device attaches to either side of the chair and secures to wheelchair metal frame. To open the attachment door, the user folds the door down to form the base of the cup holder, and adjusts the arms to accommodate 16-ounce t
Large Glove Box
The Large Glove Box is an under seat caddy for a wheelchair or scooter designed for use by individuals with mobility disabilities. Made of water-resistant nylon, this caddy attaches under the seats of most scooters and motorized wheelchairs with the included hook-and-loop straps. DIMENSIONS: 12 x 5 x 9 inches.
Large Or Small Book / Utility Bag
Vinyl or sailcloth book/utility bag with loops to slide over push handles. Bags are made to custom sizes, with large being over 12 inches wide by 12 inches high by 2 inches deep and small being under 12 by 12 by 2. Wide color range.
Large Oxbow Headrest (Model Lox100)
The Large Oxbow Headrest, model LOX100, is a headrest designed for use by use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who rotate their heads while seated in a wheelchair. It has flared ends that provide a flat area to rest the cheek when the head is turned to either side, and it is made of multi-layered foam with a zippered cover. DIMENSIONS (LxH): 16 x 8 inches.
Large Padded Headrest (Model Cph100)
The Large Padded Headrest, movel CPH100, s a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. This large multi-layered foam padded headrest provides comfort, support, and positioning. The headrest comes with a zippered Triptex cover. DIMENSIONS: 13 x 10 inches.
Large Wheelchair Headrest (Model 75909)
The Large Wheelchair Headrest, model 75909, is a headrest designed for use by individuals with lower extremity, mobility or severe physical disabilities, spinal cord injury and others who use wheelchairs. This headrest is designed to increase head support and comfort with minimal loss of range of vision to the user. It is made of highly tear-resistant polyurethane designed with relief contours for the user's ears. The width of the headrest is adjustable. It has a sturdy, full length metal insert
Larger Crutch Bag For Wheelchair
The Larger Crutch Bag for Wheelchair is designed for use by people with lower extremity, walking or mobility disabilities who use crutches and a wheelchair. This bag, which is available made of nylon, sunbrella, or cordura, provides the means for transport a pair of crutches while seated in a wheelchair. The bag attaches to the back of a wheelchair and fits one pair of crutches in an upright position. It has a flap with a Velcro closure and a side pockets that are large enough to fit magazines o
Lateral Facial Component (Model Lfc-1)
The Lateral Facial Component model LFC-1 is an accessory for the SOFT-1 or SOFT-2 headrest systems (see separate entries) that provides additional support to persons with severe ATNR or difficulty aligning in midline position. The support consists of two independently adjustable pads placed in front of the user's ears and extending from approximately the cheekbone to the crest of the head. The user's hearing or visual field is only minimally interfered by the device. The LFC-1 may be ordered thr
Lautzenhiser Drive Control
The Lautzenhiser Drive Control is a powered wheelchair controller designed for use by individuals with spinal cord injury or severe phyical disabilities. This fully-proportional alternative input device for powered wheelchairs features a miniature tilt-sensor that can be worn on the head, hand, finger, or foot providing precise command wheelchair and seat functions. Features include null-width (neutral zone) adjustment, adjustable on-delay timer (controls the time until the sensor is activated a
Leg Contracture Pad (Models 703080 &703082)
The Leg Contracture Pad is a legrest panel designed for use by individuals who use wheelchairs and whose legs are in flexion contracture. This unit fits between the legrests between the seat and the footplates and has a firm foam-padded plywood base covered in wipe-clean vinyl. DIMENSIONS: Model 703080 feets 16-inch wheelchairs and model 703082 fits 18-inch wheelchairs.
Leg Guard (Model 59)
The Leg Guard, model 59, is a legrest strap designed to prevent the wheelchairuser's feet from slipping back off the footrests. This webbing strap fastens to the legrests with Velcro fasteners. DIMENSIONS: 2 inches wide.
Leg Hugger (Model 6355)
The Leg Hugger, model 6350, is a legrest panel for people with lower extremity or mobility disability or spinal cord injury and others who use wheelchairs designed to prevent the wheelchair user's feet from sliding off foot plates between the legrests. This panel lies flat against the leg bars to allow full use of the foot plates and attaches to wheelchairs with quick-release straps. Cushioned with foam padding, the panel is covered in wipe-clean vinyl. DIMENSIONS (WxH): 15.5 x 9 inches. Fits ch
Leg Rest With Seat Mounting Brackets
Custom size pad and pair of custom angled Kydex or aluminum brackets which mount to front edge of solid seat. Brackets may be hinged to provide adjustability on wheelchair with elevating legrests.
Leg Support For Wheelchair
CUSTOM ADAPTATION PURPOSE: To enable an individual with a fused knee to use a wheelchair. The legrest extends straight out from the wheelchair seat, supporting the legs while leaving the foot free. A support frame was created from square steel tubing and mounted on the right front frame of the chair and under the seat. A horizontal piece comes out from the wheelchair frame and attaches to a vertical piece that supports the horizontal leg support. The support itself is made from half a section o
Legrest Pad (Models 440P1 & 440P2)
The Legrest Pad is an injection molded, steel reinforced calf trough with foam padding. It has an elliptical shape, curved to fit the natural contour of the leg. It attaches to the footrest support with fitted clamps. Adapter plates are available for some makes of wheelchairs. These can be used with Side Thoracic Support hardware.
Legrest Panel (Model S064)
The Legrest Panel, model S064, is designed for use by individuals who use wheelchairs. This fabric panel attaches to the footrest posts with adjustable Velcro straps and cradles the back of the legs with its sling-like design.
Lestronic Ii Battery Charger (Model 6815)
The Lestronic II Battery charger, model 6815, is a battery charger designed for use with wheelchairs and scooters. This 12-volt charger is a ferroresonant battery charger and has a patented electronic timer. The charger is fully automatic, turning on automatically when plugged in and shutting off when batteries are fully charged. The charger adds to range with each charge and to total battery life. This charger is designed for use with wet or flooded batteries (water required to be added to the
Lestronic Ii Dual Mode (Models 17750, 18330, & 18350)
The Lestronic II Dual mode, models 17750, 18330, and 18350 are battery chargers designed for use with scooters and powered wheelchairs. This fully-automatic charger is electronically controlled and has two modes. One mode charges conventional liquid electrolyte batteries, other charges gel-cell or other sealed cell batteries. The direct current (DC) output is 24 volts, 8 amps, tapering to 3 amps. DIMENSIONS (HxWxL): 8 3/16 x 8 11/16 x 6 7/16 inches long. WEIGHT: 16 pounds.
Levenger Lap Desk
The Levenger Lap Desk is a lap tray designed for use by individuals with upper extremity or mobility disabilities. This wooden desk is designed to rest on the arms of a chair to keep weight off the user's lap. This kidney-bean shaped desk is equipped with elastic straps to hold books and materials in place; included on the strap is a pen holder loop. OPTIONS: Transparent writing pad and clip-on Laplighter light. DIMENSIONS (WxHxD): 32.5 x 16 x 0.25 inches. COLOR: Natural cherry or dark cherry.
Levered-Power Wheelchair
The Levered-Power Wheelchair is a prototype designed for individuals with mobility disabilities. This device includes a hand lever that activates secure hitching to the frame of the wheelchair. It allows any wheelchair to be powered in a rowing motion.
Lexan Half Lap Tray, Left (Model 16C012-1L) & Lexan Half Lap Tray, Right (Model 16C012-1R)
The Lexan Half Lap Tray is a lap tray is designed for use by individuals who use wheelchairs. This tray has an epoxy-coated-steel slide- on mounting bracket. A hinged system allows the clear, see-through tray section to fold completely over thus leveling it with the side of the wheelchair when not in use. No tools are required for attachment. Model 16C012-1R is for right-handed use and model 16C012-1L is for left-handed use. DIMENSIONS (WxL): 10 x 20 inches.
Lifestyle Transfer Board (Models Rtl6044 & Rtl6045)
The Lifestyle Transfer Board, models RTL6044 and RTL6045, is a transfer board designed for use by individuals with balance, lower extremity or mobility disabilities or spinal cord injury. Intended for use in transfers to and from wheelchairs, this board features two horizontal cut-out handles for gripping and carrying. It has rounded corners with tapered ends. The board is made of Baltic birch with a clear lacquer finish. DIMENSIONS: Available in lengths of 24 and 30 inches. CAPACITY: 250 pounds
Lift-Off Lap Cushion (Model 307050)
The Lift-off Lap Cushion, model 307050, is a lap tray designed to provide individuals who use wheelchairs with proper positioning and a work surface. This cushion is held in place with Velcro two closures that wrap around the front armrest posts and which are easily released by the act of rising from the chair; the closures also feature easy-to-grasp, easy-to-see loops which provide the user with the option of removing the cushion before rising. Covered in durable, liquid proof vinyl, the foam-p
Light And Go Mobility Light
Light and Go Mobility Light is a wheelchair accessory designed for any aged individual who uses a wheelchair, walker, or rollator. It assists individuals who have difficulty seeing while walking with their walker or rollator or while using their wheelchair. It comes with three bright, long-life LEDs, with two standard AA batteries and a flashlight that can be attached to the wheelchair. This product allows for hands-free use with wheelchairs, walkers, and rollators. It also comes with a protecti
Light Duty Magic Arm System
The Light Duty Magic Arm System is a lightweight adjustable mounting system which can be attached to a wheelchair, table, or bed to allow users to have greater independence. System has a single articulated extendable arm (14 inches long – 24 inches long) with two sections and a heavy-duty clamp. Mounts securely to any wheelchair, table or bedrail and holds up to 3.3 pounds.
Lightweight Plastic Transfer Board
The Lightweight Plastic Transfer Board is designed to aid individuals who use wheelchairs in transferring to and from the wheelchair. Molded of high-impact plastic with reinforcement ribs for maximum stength, this board provides a rigid transfer surface between any two level surfaces. DIMENSIONS (WxL): 8 x 30 inches. CAPACITY: 220 pounds.
Linear Lap Desk With Led Light
The Linear Lap Desk with LED Light is a lap tray designed for use by individuals with lower extremity or mobility disabilities and others who use wheelchairs. This oval lap desk is lightweight with rounded, smooth edges. It has a laminated plywood surface mounted on an oval wedge-shaped cushion filled with a soft foam pillow. The laminated surface is glare-free to help reduce eye strain. Other features include an attached gooseneck LED light. The cushion conforms to any lap and adjusts from fl
Lite Transfer Board (Model Bk6466)
The Lite Transfer Board, model 6466, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. Made of birch plywood with a lacquer finish, this board has tapered ends and rounded edges for easy sliding. DIMENSIONS (LxWxD): 24 x 8 x .05 inches. WEIGHT: 37 ounces.
Loc-Line Echo Dot Bracket
The Loc-Line Echo Dot Bracket is a do it yourself device designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. This bracket is intended to support the weight of the Amazon Echo and DOT with a ½ inch Modular Hose, Loc-Line tube and a clamp so that the Dot can be positioned closer to the user.
Low Lapboard.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Provides a work surface at a convenient height for food preparation. Can also be used to carry items from one place to another. Directions, diagram and materials for simple wooden tray that fits over the skirt guards of a wheelchair armrest. Edging along the front of the board prevents items from rolling off. SKILLS REQUIRED: Woodworking. AUTHOR: Fahland, B. TITLE: Wheelchair Selection: More Than Choosing a Chair With Wheels. REF:Book: Sister Kenny Ins
Low Shear Power Recliner
Low shear power recliner for Invacare Arrow recliner frame or sectional frame, or Everest and Jennings recliner frame -47 or -49 and standard Marathon sectional back wheelchairs. High quad seating system replaces standard seat assembly. Comes assembled, includes reclining frame, rigid back, rigid seat, standard headrest, quick release reclining arm hardware, arm and leg troughs, underseat or back module mount, and a toggle switch to control the system. Back height of 16 inches to 25 inches in on
Lower Extremity Supports, Solid Calf Panel, Calf Troughs, & Calf Cuffs
Legrests with calf supports. Model 108-3000 is solid calf panel with fixed or swing away brackets, 1 inch drop hooks, 30 degree clamp, all sizes. Model 108-4000 is molded calf trough which mounts to elevating legrests, small has 3 inch circumference, large for 5 inch circumference leg, specify length. Model 108-6000 is molded calf trough which mounts to solid wheelchair seat, small for 3 inch circumference leg, large for 5 inch circumference, specify length. Also available: calf cuffs to mount t
Luggage Rack (Model 97)
The Luggage Rack, model 97, is designed for use with wheelchairs. This rack mounts to the wheelchair step tubes and extends back to support luggage.
Magic Arm
The Magic Arm is a mounting attachment for wheelchairs for positioning cameras, joysticks, or other adaptive equipment. This flexible arm has three joints, a 90 degree pivoting end, a 360 degree rotating end, and a 360 degree rotating elbow. Both ends have studs that are tapped and fit any standard 5/8 inch socket. Includes a flash shoe and a camera mounting bracket. This device is designed for use with the Beneficial Designs Super Clamp (see separate entry). DIMENSIONS: Extended length is 19.7
Magicwheels
MAGICWHEELS are two-gear wheelchair wheels designed for use by individuals with mobility disabilities or spinal cord injury. Low gear requires half the effort of standard pushing for climbing hills, ramps, curb cuts, or door thresholds. When going downhill, only half the force is needed for stopping. The user engages low gear with a click of the hub. When not in low gear, the user applies the same level of force as with a standard wheelchair wheel. In low gear, an automatic hill-holder prevents
Mako Performance
The Mako Performance is an elastomer replacement wheelchair tire designed for use by wheelchair users. These rolling resistance tires are made with High Round Elastomer technology and are comparable to pneumatic racing tires. DIMENSIONS: 24 x 1 inches. This tire fits any manufacturer's wheel requiring a 24 x 1 or 24 x 1.25 inch tire whose rim is 15 to 17 millimeters (mm) wide and at least 7 mm deep. It will fit 540 mm rims as well. COLORS: Green, black, blue, red, or yellow.
Marathon 24 & Marathon 8
Airless wheelchair tires. One piece, snap on, lightweight Endurothane II construction to replace conventional rubber tires. Maintenance free. Lifetime guarantee against flats, blowouts and pressure loss. AA24100 fits most major brands of wheelchair tires 24 inches diameter. AA8101 fits most shallow 8 by 1 inch rims. AA8102 fits molded plastic and most other deep cavity 8 by 1 inch caster rims.
Massaging Pillow (Models 3128 & 3128A)
The Massaging Pillow, models 3128 and 3128A, is a vibrating pillow designed for use by individuals with upper extremity or severe physical disabilities.This pillow was designed to be used to help promote proper posture and provide back and neck support for activities such as activating a capability switch. It has low and high vibrating modes, and it can be used while in a wheelchair, office or automobile. POWER: Requires 2 D batteries. DIMENSIONS (DxLxW): 5 x 13 x 13 inches (model 3128) or 4 x 1
Maxidy Arm Rest Pads
Maxidy Arm Rest Pads, desk length and full length, are designed for use with all wheelchairs. Both arm rests are constructed of long-lasting, durable urethane foam. Maxidy arm cusions offer a universal fit on all wheelchair models and are guaranteed to be rip-free, soft and comfortable. They are easily installed on wheelchair arms and all necessary hardware is included.
Maxidy Calf Rests
Maxidy Calf Rests are legrest pads designed for use on wheelchairs. They are constructed of long-lasting, durable urethane foam and will fit on all types and models of wheelchairs. Maxidy Calf Rests are guaranteed to be rip-free, soft and comfortable. They are easily installed and all necessary hardware is included.
Mc5
MC5 are suspension caster forks designed for use on lightweight low-profile sports wheelchairs. Available in a choice of light-, standard-, or heavy-duty models these aircraft aluminum forks retrofit most sports chairs and feature polymer shock absorbers that reduce the effect of vibration on the wheelchair user. They also reduce the chance of the user being pitched from the chair when the front wheels encounter obstacles; each wheel travels independently over the obstacle. These forks offer a c
Mccain Wheelchair Roller (Models Br20)
The McCain Wheelchair Roller is a wheelchair exercise roller designed for use by individuals who use wheelchairs. The unit consists of a ramp with non-slip tread attached to a set of rollers. The user wheels any manual wheelchair up the ramp, parks with the rear drive wheels on the rollers, and secures the chair. The user can then wheel in place to achieve a workout. This device is equipped with an eight-pound flywheel for added momentum. OPTIONS: Resistance unit. DIMENSIONS: The unit has 4.5 in
Medline Back Support (Models Mscbl16, Mscbl18, Mscbl20, Mscb16, Mscb18, & Mscb20)
The Medline Back Cushion is a wheelchair back support cushion designed for use by individuals with mobility disabilities. This support cushion fits in front of a standard wheelchair back, eliminating the hammock effect of a sling back. Straps hold the cushion in place. The cushion has two layers of high-density foam to support the entire back and a ShearX all-way stretch cover to reduce skin shear. The cover is antimicrobial and fluid-proof. It is available with or without lumbar support. SIZES:
Medline Reclining Back Cushion (Mscbr16, Mscbr18, & Mscbr20)
The Medline Reclining Back Cushion is a foam wheelchair back support cushion designed for use by individuals with mobility disabilities. A replacement for the standard wheelchair sling back, this cushion creates a fixed 10-degree angle of recline. The back support has two layers of high-density foam with a built-in rigid inset and a ShearX all-way stretch cover. The cover reduces skin shear and is antimicrobial and fluid-proof. The back support fits 16-inch wheelchairs (model MSCBR16), 18-inch w
Melrose Performance Polymer
Melrose Performance Polymers are shock absorption materials for wheelchair casters designed for use in customizing Frog Legs suspension caster forks (see separate entry). Frog Legs caster forks replace a wheelchair's existing caster forks with shock absorbing hinges that use Melrose Performance Polymers to absorb the impacts that a wheelchair's casters encounter. The polymers are cylindrical, and they fit in the Frogs Legs fork where they absorb vibration to reduce shaking and bouncing in the fr
Melrose Wheelbag Usa (Model 45182)
The Melrose Wheel Bag USA, model 45182, is a bag for wheelchair wheels for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who user a wheelchair. The bag holds up to four spare wheels in a protective padded compartments. Wheels are protected from scratches and marks. The bag keeps a person's wheels together so if that person is traveling with a team or a group of wheelchair users, his or her wheels are kept separate from other wheels. The b
Mesh-Back Wheelchair Glove Series (Model Br607)
The Mesh-back Wheelchair Glove Series, model BR607, by Hatch are a line of all-purpose push gloves for manual wheelchair users. The gloves have half sleeves for the fingers and thumbs, and are made of leather with crocheted mesh backs. A velcro closure is featured on the backs of the wrists. COLOR: Available in 8 assorted colors.
Metatarsal Cushion
This Metatarsal cushion is meant to cushion the balls of the feet and relieve pressure in the middle foot. The stretchy polymer gel pads relieve pressure in the middle foot area. They come in a pair or a left and right set. Can be slipped over second toe so it will stay in place. Corrected foot support promotes better posture.
Micro Cellular Polyurethane Tires
Micro Cellular Polyurethane Tires are wheelchair tires fabricated with microscopic air cells trapped in a matrix of polyurethane rubber. These fully molded snap on tires are designed to provide a cushioned ride, and are lighter than standard hard rubber wheelchair tires. SIZES: Various models and sizes available.
Micro-Tech Seat Belt Alarm
The Micro-Tech Seat Belt Alarm is a wheelchair seat belt and wandering patient system designed for use by individuals who use wheelchairs and have Alzheimer's disease or other cognitive disabilities and are at risk for falls in homes or hospitals. This seat belt is equipped with a standard sensor unit and a Velcro fastening buckle that, once disengaged, alerts a caregiver or hospital staff that the user is exiting the wheelchair and may wander or fall. The Seat Belt Alarm is intended for use wit
Midline Control Bracket
Swingaway mounting bracket for power wheelchair control box. Uses existing control box clamp for mounting to armrest. Aluminum. Round or flat bar stock.
Miller's Mounting Hardware Components
The Miller's Mounting Hardware Components are designed for affixing wheelchair accessories to solid seat and back panels or to 7/8 and 1 inch wheelchair frame tubing. Fixed, swingaway, and adjustable type clamps and brackets are available. COLOR: Silver or black chrome finish.
Mind-Controled Wheelchair
---- PROTOTYPE --------- PURPOSE: To create a prototype of a mind-controlled wheelchair using brain computer interface technologies for individuals with mobility and severe disabilities. Researchers at École Polytechnique Fédérale de Lausanne in Switzerland have developed a mind-controlled wheelchair which uses an artificial intelligence system called “shared control” making the brain-machine interface more usable. An individual uses his/her thoughts to create specific brain patterns that are re
Mini Mobility Rucksack
Mini Mobility Rucksack is a compact bag designed for use on a wheelchair, scooter, children's chairs or those wanting a smaller bag. The shoulder straps secure the bag over the pushing handles of a wheelchair or though the headrest of a scooter. Alternatively the braid and clip system can be used on the pushing handles or back of a wheelchair and many power chairs. It features a large compartment and smaller front pocket, padded shoulder straps with a mesh backing for breathability and two color
Mini Oxygen Tank Holder For Wheelchairs (Model F706201001)
The Mini Oxygen Tank Holder For Wheelchairs, model F706202001, is a wheelchair oxygen cylinder carrying case designed for use by individuals with mobility and respiratory disabilities. It attaches to the handles and frame of the wheelchair and positions the tank behind the wheelchair to avoid interference with the user’s head or back. The tank holder is made of heavy duty waterproof nylon and has two pockets that can be used to hold one or two cylinders or other small supplies such as tubing.
Mini Pouch (Model 9)
Mini pouch attaches beneath the armrest on standard wheelchairs, armrest is loosened and straps slipped between the pad and arm of the frame. Single snap closure. Cordura nylon. 8 colors.
Mjm Transfer Board (Model 600)
The MJM Transfer Board, model 600, is a transfer board designed for use by individuals with mobility disabilities, spinal cord injury, or severe physical disabilities. The board is made of high density polyethylene, and has eight carrying handles and three web nylon restraint straps with side release plastic buckles. DIMENSIONS (LxW): 71 x 23.5 inches. The restraint straps are 2 inches.
Mk Battery.
Alkaline batteries. 6 or 12 volt variety of styles including gel and sealed lead acid batteries. Battery chargers and battery service accessories also available.
Mobili-T Rover Off Road Wheelchair Kit
The Mobili-T Rover Off Road Wheelchair Kit is an all terrain platform for powered wheelchairs designed for use by individuals with mobility or severe physical disabilities or spinal cord injury. Designed to allow the user to access parks, beaches, woods, golf courses, construction sites, farms, and nature trails, this device consists of a large metal platform equipped with over-sized all-terrain tires. The platform is mounted by driving the powered wheelchair up a ramp and then powered by the wh
Mobilizr
The MOBILIZR is a torso support and wheelchair seatbelt for use by people with lower extremity and mobility disabilities, spinal cord injuries and others who use wheelchairs and need assistance to maintain or regain an upright position. This product requires no tools for installation on a wheelchair or scooter with push handles. It fits around the waist and over one shoulder. The MOBILIZR allows the user to bend forward, and then it aids the user to return to an upright position. It adjusts from
Modification To Quick-Release Wheelchair Wheels
CUSTOM ADAPTATION PURPOSE: To prevent quick-release wheelchair wheels from being inadvertently released. The push rims on the quick-release wheels had been removed because the chair user could not propel the chair independently. Doing so, however, exposed the buttons which released the wheels, creating the danger of an inadvertent release if the wheels were bumped while going through doors. The quick-release feature was locked by machining sleeves to fit over the buttons and gluing them in pla
Modifications To Protect A Wheelchair
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adaptation to protect various parts of an electronic wheelchair for a child with right hemiplegia, vision impairment, and developmental delay. There were a number of fittings on the chair that needed attention and had been damaged by the child. The first issue was the control panel for the joystick, which had a thin film cover over the membrane touch buttons that set the direction and mode. The buttons didn’t work unless they were
Modu-Tray
The Modu-Tray is a lapboard with bookholder designed to act as a tray or writing board for wheelchair users. Interchangeable inserts allow the user to have an adjustable easle for computer keyboard, reading, games, or a communication board, or a microwavable, dishwasher-safe fixed bowl that will not tip. The tray is made of a see-through Lexan plastic and features a cutout. It may be modified to fit standing tables, bolster chairs, and hospital bed tables. When fitted to a wheelchair, the tray i
Modular Seat And Back Cushions
The Modular Seat and Back Cushions are designed to work with custom systems or replace standard wheelchair upholstery. The cushions ($68 and up) are made of foam, with an easy to clean skin surface. The back pads ($23 and up) may be installed permanently with glue, attached with velcro, or bolted to the seats with hardware.
Modularhose.com Assistive Technology Double Kit (Model 90655)
The ModularHose.com Assistive Technology Double Kit, model 90655, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 6 feet of
Modularhose.com Assistive Technology Double Spring Clamp Kit (Model 90674)
The ModularHose.com Assistive Technology Double Spring Clamp Kit, model 90674, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a 4 x 6 inch plat
Modularhose.com Assistive Technology Kit (Model 90650)
The ModularHose.com Assistive Technology Kit, model 90650, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 3 feet of Loc-Li
Modularhose.com Assistive Technology Kit Plus (Model 90652)
The ModularHose.com Assistive Technology Kit Plus, model 90652, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 6 feet of L
Modularhose.com Assistive Technology Kit With Two Plates (Model 90654)
The ModularHose.com Assistive Technology Kit with Two Plates, model 90654, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes
Modularhose.com Assistive Technology Spring Clamp Kit (Model 90673)
The ModularHose.com Assistive Technology Spring Clamp Kit, model 90673, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a 4 x 6 inch plate, 2 5.75
Modularhose.com At Ipad Kit (Model 90670)
The ModularHose.com AT iPad Kit, model 90670, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system can be used with iPad 1 and iPad 2. The kit comes with an iPad holder with a silicon edge for protection and grip, an integrated fixed mount plate attached to the iPad holder, 2 spring clamps with integrated fixed mount, 2
Modularhose.com At Starter Kit (Model 90680)
The ModularHose.com AT Starter Kit, model 90680, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes with all the common parts used in the assistive tec
Modularhose.com Round Tube Clamp Kit (Model 90750)
The ModularHose.com Round Tube Clamp Kit, model 90750, is a computer or communicator mounting kit for wheelchair or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The kit is intended to be used with Loc-Line 1-inch or 0.88-inch diameter tubing. Plates are made of stainless steel. The kit includes five-piece round tube clamp with knob, Loc-Line connector, Loc-Line double socket f
Modularhose.com Spring Clamp Kit With Plate 1 Foot (Model 90665)
The ModularHose.com Spring Clamp Kit with Plate 1 Foot, model 90665, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a round plate connected to a
Modularhose.com Spring Clamp Kit With Plate 2 Feet (Model 90667)
The ModularHose.com Spring Clamp Kit with Plate 2 Feet, model 90667, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a round plate connected to a
Molded Transfer Board (Model 6032)
The Molded Transfer Board, model 6032, is a high-impact, heavy duty plastic board with tapered ends designed to assist individuals with mobility disabilities with transfers. The board is 8.25 x 24.25 inches.
Monster Bag
The Monster Bag is designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. The bag straps over the scooter or wheelchair seatback to provide storage for shopping, laundry, groceries, and more. The device is made from high quality water resistant polyester.
Morph‚Ñ¢ Wheels
Morph™ Wheels are a foldable wheelchair wheels for use by people who use wheelchairs. Winner of the Medtrade 2013 Innovation Award and the London Design Museum 2013 Product of the Year in Transportation, Morph™ Wheels are the world's first foldable wheelchair wheel available on the market for purchase. They allow users to travel in cars, trains and airplanes without being limited by storage space (they fit in overhead storage compartments). Users can change these tires without complex tools. Mor
Moss Lap Tray
The Moss Lap Tray is a molded plastic lapboard designed to mount to Otto Bock MOSS II seating system armrests (see separate entry) with the U-shaped aluminum frame. Fits 9.5, 11.5, 13.5, 16, and 18 inch seating systems.
Mother's 3Rd Arm
Mother's 3rd Arm is a flexible, portable cup or baby bottle holder designed for use by children and adults with upper extremity disabilities. This device consists of a large cylinder affixed to a long flexible neck with a large clamp at the base. The adjustable clamp permits the device to be secured to the edges of tables or desks, the back of automobile seats, bed rails, or to the tubular frame of a stroller, wheelchair, or high chair. The cup or baby bottle is placed in the cylinder and the ne
Motorised Wheelchair Mover
CUSTOM ADAPTATION PURPOSE: To enable a recreational therapist who had a back injury to move clients who used wheelchairs around the facility. Because of the back injury, the therapist was unable to push wheelchairs or lift heavy objects. To build the unit, the motor, gearbox, elctronics, and rear wheels of a second-hand scooter were used in conjunction with a chasis built of square hollow section steel. The unit has a platform at the front on which the wheelchair, with its user, is loaded. The
Motorized Wheelchair Trainer (Model 1520)
Motorized wheelchair trainer is a wheelchair control switch assessment designed to provide assessment of user's perceptual skills prior to purchase of a powered wheelchair. The device contains four directional arrows which light up and sound a beeper in response to the direction of the joystick. In use, the teacher or therapist stands behind the client who is seated in a conventional wheelchair. By watching the indicator arrows on the device, the teacher can push the wheelchair in the direction
Mount 'n Mover
The Mount 'n Mover is a wheelchair mounting kit for communicators, tablet or laptop computers, or a camera mount for wheelchair designed for use by individuals who use wheelchairs. The device can also be used to mount trays, easels, reading stands, remote controls and more. Available in single- or dual-arm horizontal models, the device is equipped with a quick-release mounting plate offering 0 to 90 degrees of tilt, a paddle to unlock the wrist joint to rotate the attached tray or device, and a
Mulepack (Model 7012) & Mulepack Ii (Model 7013)
The Mulepacks are wheelchair back pouches designed to carry things for the person in a wheelchair. Each caddy is made of heavy urethane coated Nylon pack cloth with a strong poly webbing for the straps and 2-way zippers with steel rings for good grip when opening or closing. The Mulepack II (7012) has a main storage area with a wallet and key pouch and large envelope pocket. The Mulepack I has a main storage area and one front envelope pocket. The packs will fit wheelchairs with or without push
Multi Purpose 5 Pocket Pouch (Model 156)
The Multi Purpose 5-Pocket Pouch, model 156, is a wheelchair side pouch which may also be used on walkers. This transparent plastic carrying caddy features two adjustable hooks for fastening.
Multimode Interface (Model 3420)
Permits the use of proportional or switch actuators to operate an Everest & Jennings power wheelchair plus additional devices such as a power recliner, environmental control system, computer and/or communicator. Two wheelchair operating modes include adjustments for speed, acceleration and deceleration. Additional adjustments vary proportional joystick throw (sensitivity), set the veer rate (steering amount) when using a switch actuator, and select momentary and/or latching (continuous) whee
Multimode Interface (Model 3470)
Permits the use of proportional or switch actuators to operate a Quickie power wheelchair plus additional devices such as a power recliner, environmental control system, computer and/or communicator. Two wheelchair operating modes include adjustments for speed, accleration and deceleration. Additional adjustments vary proportional joystick throw (sensitivity), set the veer rate (steering amount) when using a switch actuator, and select momentary and/or latching ( continuous) wheelchair drive. Tw
Multimode Scanner (Model 3370) & Scanner Display (Model 2995)
The Scanner, in conjunction with a single switch actuator, is used for mode selection and operation of a Multimode Interface. The Scanner converts single switch actuator commands into the four directional commands (forward/reverse/left/right) required for system operation.
My4Hands
My4Hands is a lapboard for use by people with lower extremity or mobility disabilities, spinal cord injury and others who use a wheelchair. The My4Hands independence assistant is a polyethylene board that has a proprietary "hold fast" high friction material coating on each side so the lapboard will hold position on the user's lap and items placed on the lapboard will remain in place. My4Hands also insulates the user's legs from heat generated by objects (such as laptop computers or cooking pots
Mydesc Arm - Standard And Removable Models
The MYDESC Arm is an add-on armrest wheelchair accessory designed to enhance the versatility of the MYDESC Custom Desktops (see separate entries) or to be used alone. This accessory allows the MYDESC units to be mounted on the side of armchairs and wheelchairs. This steel arm is padded with foam and available in two configurations: Standard and Removable. The MYDESC Standard Arm (model 347-S501) is designed to be a fixed accessory and attaches directly to wheelchairs and other furniture using st
Mydesc Custom Desktops
The MYDESC Custom Desktops are adjustable lapboards ergonomically designed to provide a hard writing or reading surface to wheelchair users and other individuals who work away from a desk or table and to alleviate the eye strain and neck pains associated with lap work. These portable units enable the user to swivel, tilt, or pivot the desk surfaces through an infinite number of positions in order to achieve the most comfortable desk surface accessibility possible. ADJUSTABILITY: These Custom Des
Mydesc Flip Top Storage Desk (Model 250-31)
The MYDESC FlipTop Storage Desk, model 250-31, is a lapboard designed for use by wheelchair users. This laptop desk is suitable for an artists or students who needs a place to put their supplies. It has a tilting work surface that lifts to reveal a storage compartment. Because both sides of the work surface are supported by a ball-joint, the surface can be tilted or shifted from right to left, and one side swings away for transfers. An Air Spring Lifter helps to ease lifting and lowering of the
Mydesc Scooter Model, The (Model 5000)
The MYDESC Scooter Model, model 5000, is a swing away lapboard designed for use with scooters. This lapboard attaches to the bottom of the scooter seat on a curved post that fits between the seat and the controls. The work surface features tilt-, height-, and swing-away adjustments. The unit features a transparent acrylic work surface, powder-coated steel tubing, and aluminum brackets that support up to nine pounds. The unit rotates and rises with the seat and it can independently swing out of t
Mydesc Tilt-Top Desks
The MYDESC Tilt-top Desks are lapboards designed to provide an adjustable hard writing or reading surface for persons who work away from a desk or table, or for wheelchair users. These portable desks are ergonomically designed to accommodate the user's needs by swiveling, tilting, and pivoting through an infinite number of positions. When use of the desk surface is completed, the desktop swings away from the user's body with a single wrist motion. There are four different tilt-top models availab
Nantahala Wheelchair Tire, The
The Natahala Wheelchair Tire is a replacement rubber tire designed for use by wheelchair users. This high-performance tire will not mark floors and is dirt resistant. It is designed to perform well for extended distances. DIMENSIONS: 26 x 1 inches. COLOR: Charchol.
Natural Birchwood Overlay (Models 11D.4A To 11D.4C)
The Natural Birchwood Overlay, models 11D.4A to 11D.4C is designed for use with wheelchair trays by Consumer Care Products Inc (models 11D; see separate entries). These overlays have a clear lacquer finish, and snap in and out of the trays. The overlays are designed to allow the user to benefit from the clear surface of the tray when moving, and from the opaque surface of the Birchwood insert when working on the tray. DIMENSIONS: Model 11D.4A fits trays 16 x 20 x 1/4 inches; Model 11D.4B fits tr
Natural-Fit
The Natural-Fit is a hand rim designed for use on wheelchairs. This rim replaces the chair's existing hand rim and comes in two pieces: The contoured thumb area and the oval component. The combination of these two components provides a gripping surface, a specially contoured thumb rest, and dual surfaces for propulsion and braking. The system is available with rivet nut or tab mounting and attaches to standard spoke wheels with either a six-position rivet nut mount or a six-position tab mount.
Ne-At Headrest Bracket
The NE-AT Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury, cerebral palsy and other individuals who need adjustable head support. This hinged bracket has 0.25-inch countersunk mounting holes spaced 1 inch apart, with a spring loaded crank handle for tightening in tight spaces.
Ne-At Interim Leg Support
The NE-AT Interim Leg Support is a wheelchair leg support designed for people with lower extremity or mobility disabilities or spinal cord injury and others who use a manual or power wheelchair. It is intended to provide temporary extra lower leg support for wheelchair users who are in a cast or who need additional support for some other reason. The unit has a pad to support the user's lower leg, a double ball and socket joint to adjust the position and angle, a clamp for attaching to the user's
Ne-At Quick Release Mini Trap Assembly
The NE-AT Quick Release Mini Trap Assembly is a a wheelchair mounting bracket that can support an armrest, a drink holder, a tray, or a laptop computer mount. This small, strong quick-release bracket comes in two versions, angle adjustable or not angle adjustable, and it has optional locking pins. DIMENSIONS: 2 x 2 x 0.75 inches.
Neasy Swing Away Aug Com Mounting System
The NEasy Aug Com Swing Away Mounting System is a wheelchair mounting kit for communicators or lapboard mounting hardware designed fo use by individuals who use wheelchairs. This compact, heavy-duty modular mounting system for small to large devices or trays can be released and swung away by the user with only one or two pounds of pressure. Each swing away joint automatically locks into position with a stainless steel, spring-loaded pin at 0 degrees, 90 degrees (optional), and 180 degrees (optio
New And Rebuilt Electric Motors
Electric motors, new and rebuilt, for Everest and Jennings and Invacare wheelchairs and three wheel scooters. New motors are manufacturers' original equipment with a one year factory warranty. We offer a 90 day warranty on rebuilt motors. Quantity discounts are available. Orders and repairs are handled at the factory and delivered by UPS. New motors available for E & J 3P,3W Marathon, 3V, Sprint, and 33B only. Motors rebuilt for the following: Invacare, Amigo, Pace Saver, A-Bec, Lark, Dart,
NEWS: New Electric Wheelchairs
The NEWS: New Electric Wheelchairs is a prototype that attaches to manual wheelchairs and makes them electric, eliminating the need to buy a costly electric wheelchair. It has a joystick, sub-grip, safety light, motor, cooler, docking station and electric charger.
No Limits Trike
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted motorized power tricycle add on for manual wheelchairs for individuals with lower extremity or mobility disabilities or spinal cord industry. The No Limits Trike is a power system complete with a power drive including a wheel with 12 inch disk brakes, motor, and a 24 volt battery pack mounted on the front fork with handle bar. The trike includes a left side brake lever and right side variable speed twist throttle that can b
No-Slip Grip-Clip
The No-Slip Grip-Clip is a carrying aid for wheelchair, designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. It consists of a wrap around strap with a strong aluminum spring activated karibiner clip that can be used to carry items on the front tubing of a wheelchair's frame. The clip holds the item to be carried and the strap a rubber pad embedded in the strap prevents it from sliding down the wheelchair tubing.
Non-Powered Wheels To Powered
---- PROTOTYPE --------- PURPOSE: To create a prototype of an attachable device which converts a non-motorized wheelchair into a motorized wheelchair similar to wheelchair design used by the pop-culture comic book icon of Professor Xavier form the X-Men franchise. Created by Ju Hyun Lee from Yanko Design the device attaches to any standard wheelchair providing instant motorized power. This device has potential uses for hospitals, nursing homes, physical therapy centers, and for the average wheel
Norco Push Kuffs (Model Nc94320)
The Norco Push Kuffs, model NC94320, are leather wheelchair push gloves designed to protect the hand from callouses and cuts. The cuffs cover the palm and back of the hands, leaving fingers exposed. The palm features a thick protective pad. The gloves are secured with hook and loop closures.
Nova Flashlight And Attachment (Model FL-1000)
The Nova Flashlight and Attachment, Model FL-1000, is a cane, walker and wheelchair light designed for use by individuals who use walkers, canes, and wheelchairs. The light attaches to any tube product with a diameter of .875 to 1 inch. It comes with a wrist strap and a clip that pivots 360 degrees to change the direction of the light. The light can also be detached from the clip for use as a flashlight. This light can also be used with bicycles and baby strollers. No tools are required for atta
Nylon Back Pack (Model 16C005)
The Nylon Back Pack, model 16C005, is a wheelchair back pouch designed for use by individuals who use wheelchairs. Made of heavy- weight cordura nylon, this pouch carries small items and features nylon straps for hanging over wheelchair handles, two outside pockets, and Velcro closure flaps. DIMENSIONS: (HxW): 15 x 14 inches.
Off Road Wheels
The Off Road Wheels are rear wheelchair wheels designed for outdoor use on manual wheelchairs with quick-release axles. These spoked wheels wheels provide excellent traction off paved surfaces and a more comfortable ride on paved surfaces. The set includes mountain bike style tires, rims, push rims, and hubs. DIMENSIONS: Available in 24 x 1.95 inches or 26 x 2.1 inches. OPTIONS: Mag wheels and plastic-coated push rims. COLOR: The tires are non-marking gray.
Offset Multi-Axis Headrest Hardware
The Offset Multi-Access Headrest Hardware is a headrest accessory designed for use by individuals with severe physical disabilities and spinal cord injury. This hardware comes with a horizontal bar and ring for attaching a headrest pad. Our headrest hardware also comes with a back clamp which attaches the vertical tube to the back of the chair. COLOR: Black chrome.
Olympiad Racing Hand Rim
Push rims for racing with foam coating for nonslip grip, aluminum rings with threaded aluminum stand offs (6 for 36 spoke models), 12 inch by 7/ 8 inch rim weighs 9 ounces total, mounts on spokes with rubber backed washers, easily removable for interchanging rims. Available from 10 to 19 inch outside diameter; and 5/8 inch, 7/8 inch or 1 inch hand rim diameters. Fits 24, 28, 32, and 36 spoke patterns. 20 inch model available for standard street chairs at slightly higher price. Foam coating is ov
One Way Seating Aid
One Way Seating Aid is designed for use by individuals with limited mobility in their lower extremities as a result of a stroke, spinal cord injury or cerebral palsy. It can be used in a chair or wheelchair to hold the user in position and prevent them from sliding forward. The device has an internal, one-way fabric that minimizes sliding forward and allows the user to slide back into the seat. It comes with a non-slip cover and is machine-washable.
One-Piece Econo Footrest Extender
The One Piece Econo Footrest Extender is an economical device that attaches to a wheelchair footrest for prevention of foot drop and feet from slipping behind the footrest. The raised footrest improves posture and allows for proper seating alignment. The cushioned back protects lower leg against contact with the wheelchair, and the device secures easily with quick-release straps.
Optima 2G
Optima 2G is a powered seating system designed for use by individuals with neurological or severe physical disabilities. Tilt-in-space and reclining systems are available and can be mounted on a power base (not included) from Invacare, Pride Mobility, Sunrise Medical, Leisure Lift, TracAbout, Wheelchairs of Kansas, or others. CONTROLS: Attendant controls are standard, with independent toggle switch and joystick interface controls for power base and seating system functions. Alternative input dev
Optimax
OptimaX is a bariatric seating system designed for use by individuals with neurological or severe physical disabilities. This system can be expanded in three dimensions and is available in tilt-only, recline-only, and tilt/recline configurations. FRAME (HxLxW): Back height plus 12 x seat length plus 20 x seat width plus 6 inches (tilt-only) or seat width plus 8 inches (recline only and tilt/recline). The frame has powder-coated black wrinkle finish. CONTROLS: Single post 4-position toggle switch
Optipush
The OptiPush is a wheelchair propulsion monitor designed for professional use in clinical or research settings with people with mobility and lower extremity disabilities and spinal cord injury and others who use wheelchairs. This device examines wheelchair propulsion in the natural environment of the wheelchair user because it mounts directly to most standard manual wheelchairs (a wheelchair is required but not included). The system comes with wheels and hand rims with diameters from 24 to 26 in
Original Beasytrans Transfer Board
The Original Beasytrans Transfer Board is designed for use by individuals with mobility disabilities or spinal cord injury to use during transfers. The device provides users with a safe and comfortable way to transfer from bed to wheelchair, from wheelchair to commode or shower seat, to a car and back again. It features a circular seat gliding on a track that supports the user's weight as the transfer occurs. Since there is no lifting involved, the risk of back and brachial plexus type injuries
Orthocare Economy Arm Positioner Elevator (Models 3032 & 3033)
The Orthocare Economy Arm Positioner Elevator (##3032 and ##3033) is an elevating armrest and positioner designed for elevation of the forearm. This wedge elevator is made of foam with a contoured recess to position the arm. This device can be used in bed or with the pivoting arm positioning tray for wheelchairs (see separate entry). Vinyl covers are available; call manufacturer for prices. SIZES: Small (##3032, $9.35) and Large (##3033, $14.75).
Orthocare Elevating Horizontal Arm Orthosis
The Orthocare Elevating/Horizontal Arm Orthosis - Supinated or Pronated is an elevating armrest and positioner for use with wheelchairs or other chairs. The armrest is available in two styles: Models ##3034 to ##3039 are anatomically designed for supinated, neutral positioning that inhibits spasticity; Model ##3040 has a universal design that allows for pronated positioning with natural palmar arch. The system consists of an aluminum U-channel that adapts to all wheelchair arms securely with sta
Orthocare Frame Mounting Block (Model 3042)
The Orthocare Frame Mounting Block ##3042 is a mounting clamp accessory that attaches Orthocare arm supports or positioning orthoses (see separate entries) to wheelchair arms. The block secures to the wheelchair arm with two bolts to grip the tubing, and has two screw holes for orthosis attachment.
Orthocare Leg Brace
The Orthocare Leg Brace ##4045 is a leg positioner made of polyurethane foam. It has a contoured cavity to keep the leg in place, and may be used as a legrest pad for leg comfort when wearing a cast. The brace surrounds the leg on three sides with an open top, and extends from the ankle to the mid-thigh (of adults).
Orthocare Pivoting Arm Tray (Model 3012) & Dynafoam Elevated W.h.o. (Model 3013)
The Orthocare Pivoting Arm Tray and Dynafoam Elevated W.H.O. are two separate devices designed for use one with the other. PIVOTING ARM TRAY (##3012, $45.25): This mounting clamp for a wheelchair accessory is made of ABS plastic fastened to an extruded aluminum channel with limited pivot capability. The L-bars of the clamp channel adjust to adapt to all wheelchair arms. DYNAFOAM ELEVATED W.H.O. (##3013, 36.45): This wrist and hand orthosis fits into Pivoting Arm Tray to create an elevated arm po
Orthocare Pivoting Horizontal Arm Positioner - Pronated
The Orthocare Pivoting/Horizontal Arm Positioner - Pronated is a wheelchair armrest pad that will adapts to all wheelchair arms. This device was designed to provide pronated hand positioning with natural palmar arch. The armrest is cut down at the proximal end to allow for better positioning of the arm, and is narrow at the wrist section to decrease arm roll. The arm and hand are secured in place with 2 Velcro straps. A reinforced pivot rivet pivots the arm in a horizontal plane. DIMENSIONS: 18-
Orthocare Slip-On Footrest Extenders (Model 3014)
The Orthocare Slip-On Footrest Extenders ##3014 are designed to eliminate heel slippage and override, and to provide static positioning for spasticity. The extenders are made of vacuum formed ABS (plastic). They have a raised, curved heel section and flat foot section. Padded Velcro straps cross the instep to hold each foot in place. The slip-on mounting adapts to standard footrests. The design allows a vertical fold-up position without interference. Sold in pairs.
Orthocare Sure-Grip (Models 3017 Thru 3022)
Orthocare Sure-Grip gloves are push gloves or dressing mitts designed to allow total hand use while providing complete coverage of the palm, thumb, and back of hand. The gloves are made of polyethylene and rubber with a totally padded, non-slip surface. The gloves have a Velcro cinch strap with D-ring puller. SIZES: Small, Medium, and Large for right or left hand. The gloves can be adapted to a custom fit with ordinary scissors.
Orthotic Drop Seat (Model 6331)
The Orthotic Drop Seat, model 6331, is a solid seat insert designed to lower a wheelchair seat to enable foot propulsion of a wheelchair or to enable the user to reach the footplates. This seat replaces a standard sling seat and provides adjustable drop and it may be configured to create a wedge to prevent forward sliding. A removable padded, wipe-clean vinyl cover is included. DIMENSIONS: This seat fits 18-inch wide chairs and the drop is adjustable up to 3.5 inches.
Otto Bock Tall Back And Modular Back Headrest Mounting Kit & Otto Bock Headrest Adapter Kit
The Otto Bock Tall Back and Modular Back Headrest Mounting Kit ($5) and the Otto Bock Headrest Adapter Kit ($20) are headrest accessories that allow attachment of Otto Bock headrest mounting hardware directly to the Jay Back cushion, compensating for the contour of the cushion.
Oversize Deluxe Poly-Carbonate Wheelchair Tray (Model 11E)
The Oversize Deluxe Poly-Carbonate Wheelchair Tray 11E is a lapboard for use by wheelchair users. The tray includes a universal mounting system, continuous 5/8 inch high lip/retaining edge, captive locking-knobs, and telescoping support arms for strength. The rim is fused into the plastic tray for added strength without added weight. DIMENSIONS: 24 x 24 x 1/4 with a stomach cutout 14 inches wide and 8.5-inch deep. WEIGHT: 12 pounds.
Oxbow Headrest (Model Ox100)
The Oxbow Headrest, model OX100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who rotate their heads while seated in a wheelchair. It has flared ends that provide a flat area to rest the cheek when the head is turned to either side. DIMENSIONS: 15 x 4 inches.
Oxygen Tank Holder (Model 16C204A)
The Oxygen Tank Holder, model 16C204A, is an oxygen carrying case designed for use individuals with respiratory disabilities who use wheelchairs. This nylon tank holder has two mounting straps that are adjustable to fit most wheelchairs. The top strap fits over the push handles of the wheelchair and the bottom strap fits over the tip bars. These straps are long enough to mount the oxygen tank off center to avoid contact with the user’s head and back. This case holds size D and E or other 4-inch
Oxygen Tank Holder For Wheelchair (Model F706201000)
The Oxygen Tank Holder, model F706201000, is designed to keep a cylinder of oxygen attached to the back of a wheelchair. The holder has a 5-inch inside diameter for insertion of size "E" or 4-inch diameter tanks. A 26-inch long tank is positioned off-center behind the wheelchair back to avoid interference with the wheelchair user’s head or back. The holder is made of heavy duty, waterproof black nylon.
Pack Rat Jr. Large Mini Pack
The Pack Rat Jr. Large Mini Pack is a wheelchair side pouch designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. This unit allows the user to carry items on a wheelchair. It has a large zippered main storage compartment and a front expandable net pocket, with two Velcro straps on the back for attaching the pack to the wheelchair. On the front is a net pocket for holding smaller items safely and close at hand. The unit
Pack Rat Wheelchair Backpack
The Pack Rat Wheelchair Backpack is a wheelchair back pouch designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. Made from water resistant 600D PVC coated material, it has two large straps with loops for attaching to a wheelchair with or without a push handle. The pouch has two large zippered storage compartments. There is an opening for earphones attached to an MP3 player or radio stored in pocket in the front compa
Padded Half Lap Tray, Left (Model 16C012-2L) & Padded Half Lap Tray, Right (Model 16C012-2R)
The Padded Half Lap Tray is a lap tray designed for use by individuals who use wheelchairs. This tray has the epoxy-coated-steel slide-on mounting bracket. The hinged system allows for complete folding of the tray section thus leveling it with the side of the wheelchair. No tools are required for attachment. The tray section is padded with poly foam and covered with vinyl. Model 16C012-1L is designed for left-handed use and model 16C012-1R is designed for right-handed use. DIMEMSIONS: (WxL) 1
Padded Leg Rest With Attached Foot Rest & Padded Side Panel Leg Rest With Attached Foot Rest
Custom size leg and footrest pads with two pairs of bent Kydex or aluminum brackets, mounting footrest pad to legrest pad, and legrest pad to bottom edge of solid seat with bolts through threaded wood inserts. Adjustment for length and depth available. Can also be ordered with four side pads, two on each side of legrest and two on each side of footrest. Pads are 1/2 inch thick medium density foam over 1/2 inch birch plywood, with vinyl covering.
Para Gloves (Model Pwc200)
The Para Gloves, model PWC200, by Hatch are push gloves specifically designed for paraplegic wheelchair users. These gloves have three-quarter length finger sleeves and a fully covered thumb sleeve. They are made of leather on the palm side and have a nylon mesh material with Velcro closures on the back side of the hand.
Paraplis Umbrella Holder
The Paraplis Umbrella Holder is an umbrella holder for wheelchair or stroller designed for use by individuals with mobility disabilities or spinal cord injury. The unit attaches to stroller or wheelchair to hold an umbrella to protect both the seated user and an individual pushing the chair or stroller. When in use, it swings up to hold an open umbrella. When not in use, it swings down to carry the closed umbrella at the side of the stroller or chair. The device attaches to any shape bar or tube
Paxbac
PaxBac is a wheelchair back support designed to promote a more upright posture and to provide the proper amount of back support for wheelchair users with sling-back chairs. Made of molded foam, the unit fastens to the back of most sling back chairs with built-in attachment hooks. A tension strap allows the user to increase or decrease the amount of support provided to meet the differing needs of various activities. A loop handle on the tension strap enables the user to make adjustments while rem
Pelvic Stabilization Y Belt (Model 103-4000)
Y belt pelvic stabilization system provides control of pelvic tilt, rotation and obliquity. Price includes modification of solid seat to accommodate (with new seat). Sizes: extra small (6 to 8 inch sitting depth), small (8 to 11 inches), medium(11 to 14 inches).
Pelvic Strap (Sb05)
The Pelvic Strap (model SB05) is a 1 1/2 inch nylon webbing belt designed to position, stablize and restrain an individual's pelvic area wen seated in a seating system or wheelchair. It has a push-button buckle closure. The strap's length is adjustable on one side, and there are three positioning grommets on opposite side.
Personal Tilt Desk
Personal Tilt Desk is designed for use by individuals using a wheelchair and those who need an adjustable desk. The Personal Tilt Desk is adjustable in height and also includes a cut out for additional stability. It is available in mobile or static versions. The Personal Tilt Desk top tilts to provide options for supporting and positioning objects in relation to the child.
Phat Jack
The Phat Jack is a wheelchair lifter designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This unit was designed specifically for the Melrose Rugby wheelchairs (see separate entry), but the manufacturer can customize it for other wheelchairs. To use the Phat Jack, it is rolled under the rear bar of the wheelchair's frame, and the handle is pushed down. The rear of the wheelchair stays up until the handle is lifted back up. The unit lifts and holds
Phone Holster
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual who uses a wheelchair to transport and keep within reach a cordless telephone. A holder was fashioned from plastic siding and shaped with a heat gun. The holder has side wings and a bottom support to hold the phone. A pine mounting block was shaped to receive the holster on one side and the tubular wheelchair frame on the other. Two screws fix the holder clip to the pine. Thin pine pieces are laminated on the edge of the block to prevent
Plastic Transfer Board
The Plastic Transfer Board is a general transfer device designed for those individuals with mobility disabilities to make transferring an individual to and from a wheelchair easier. Lightweight plastic board for use in home care and clinical settings.
Plastic Wheelchair Tray (Model 11A)
The Plastic Wheelchair Tray 11A is a clear acrylic lapboard that attaches to wheelchair arms with hook and loop straps that adjust with D-rings. The tray is rimless and has a radiused and polished edge. The tray has a 4-inch deep stomach cutout. DIMENSIONS: 17 x 24 x 1/4 inches; straps are 2 inches wide. WEIGHT: Approximately 5 pounds.
Playtray
The Playtray is a lap tray designed for use by children and adults with disabilities. This heart shaped tray is constructed of a durable, impact-resistant plastic and features a tabletop with a no-spill raised edge, a large storage compartment, a 360-degree gutter drink holder, and a carrying handle. The top is large enough to accommodate a standard notepad, a laptop computer, or food and drink. Its base provides stable support by fitting snugly over a person's lap. The tray is dishwasher safe.
Pocket Technician (Model 662)
The Pocket Technician, model 662, is a control switch accessory designed to aid in determining the cause of malfunctions in switch-adapted devices. The unit tests batteries, switches, and devices. Placing an N, triple-A, double-A, C, D, or 9-volt battery in the unit will cause the meter to show the battery condition. To test a switch, the switch is plugged into the female jack; when the switch is activated and working, the unit will buzz. To test a device, the device is connected to the unit; if
Pogo Wheelchair Clamp
Pogo Wheelchair Clamp is an attachment to a wheelchair to be used by wheelchair users who are using Pogo Paint Poles in an inclusive art therapy activity.
Polar Paws (Model 300)
Polar Paws, model 300, are cold weather gloves designed to ensure the users grip no matter how cold or wet it gets while maintaining hand warmth. Originally designed for use by NFL receivers, these gloves are intended for a wide range of users: Hunters, skiers, ice fishermen, waterskiers and scuba divers to name a few. SIZES: Small-XLarge. WARRANTY: Any products that are found to be defective in material or labor will be replaced at no charge.
Poly-Carbonate Wheelchair Tray (Models 11B.1 To 11B.4)
The Poly-Carbonate Wheelchair Tray, models 11B.1 to 11B.4, is a clear plastic lapboard with straps and D-rings for adjsutment, a 4-inch deep stomach cutout, and a 5/8-inch high styrene plastic rim. DIMENSIONS: Model 11B.1 is 16 x 20 x 1/4 inches; Model 11B.2 is 19 x 24 x 1/4 inches; Model 11B.3 is 24 x 24 x 1/4 inches; and Model 11B.4 is 24 x 24 x 1/4 inches with an 8-inch deep stomach cutout. WEIGHT: Models 11B.1 and 11B.2 are approximately 6 pounds; Models 11B.3 and 11B.4 are 8 pounds.
Polycarbonate Tray
The Polycarbonate Tray is a wheelchair lap tray designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. The tray is made of polycarbonate and is available with no rim or with a polycarbonate, wooden, or rubber rim. SIZES: Child for 11 to 12 inch wheelchair; Junior for 13 to 14 inch wheelchair; Teen for 15 to 16 inch wheelchair; Adult for 17 to 18 inch wheelchair; Extra-Wide for 19 to 20 inch wheelchair; 2X-Wide for 21 t
Polycarbonate Tray (Model Tr03) & Elbow Pads (Tr21)
The Polycarbonate Tray (model TR03, $125) is a lapboard 1/4-inch thick with a rim across the front and sides designed for use on wheelchairs and seating systems. There is one size tray with cutout. The Elbow Protectors (TR21, $70) come in black only and are designed to be mounted to the tray.
Polyester Wheelchair Pads (Models Msc019470, Msc019471, Msc019472, & Msc019473)
Polyester Wheelchair Pads are footplate (model MSC019470), calf (model MSC019471), armrest (model MSC019472), and seat / back (model MSC019473) pads designed for use by individuals who use wheelchairs. These soft, flame-retardant polyester pads protect and support the arms, legs, and feet. The pads are machine washable and do not mat. The calf, armrest, and seat / back pads are latex-free.
Pommel Sit-Straight
The Pommel Sit-Straight is a foam seat cushion with a built-in pommel for abduction designed to reduce sacral sitting and to limit forward movement of the pelvis of individuals using sling seat style wheelchairs. The cushion has a concave bottom and a flat top. The pommel reduces the danger of adduction contracture and has a core that extends through the cushion to the cushion base for added stability. The material of the surface of both the cushion and the pommel is made of T-Foam (see separate
Portable Computer Mount
The Portable Computer Mount is a wheelchair mounting kit for communicators and portable computers. Designed to be mounted on the right or left side of the wheelchair, this unit fits most communicators and portable computers and can be adjusted to hold the device at the right height, position, and angle for comfortable operation. This mount can be folded out of the way when not in use, but is not designed to be moved independently by the user.
Portable Foot Rest
This Portable Foot Rest is designed for individuals who are in danger of DVT or Deep Vein Thrombosis. A foot rest may be needed to correct posture. The foot rests extends, is adjustable and folds up to fit in a carry on bag.
Posey Body Holder (Model 1731)
The Posey Body Holder, model 1731, is a safety restraint for a bed or wheelchair. It consists of a wide cotton flannel body wrap with four long straps. The restraint's slot may be positioned in the front for limited movement or rear for increased movement of the user. The straps attach to a bed frame or the wheelchair tilt bars with quick-release ties. It is machine washable. SIZES: Small, medium, large and extra large. DIMENSIONS (Pad) (LxW): 41.5 x 7.5 inches (small); 48 x 7.5 inches (medium);
Posey Breezeline Pelvic Holder (Models 4411 & 4427)
The Posey Breezeline Pelvic Holder, models 4411 and 4427, is a pelvic restraint designed for people with lower extremity or mobility disabilities and others who use wheelchairs to prevent the user from sliding out of the wheelchair or geri-chair. It is available with either a double tie strap for triangulation (model 4411) or a slide buckle. SIZES: Small, medium or large. DIMENSIONS (LxW): Model 4411 is 17.75, 21 or 24 x 17 inches (model 4411) or 16.5, 19 or 23 x 17 inches (4427). Upper waist st
Posey Self-Releasing Belt (Models 4183, 4183L, 4220, 4222, 4229 & 5145)
The Posey Self-Releasing Belt, models 4183, 4183L, 4220, 4222, 4229 and 5145, are wheelchair seat belts for people with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. This belt has an airline-style buckle allowing for one-handed release by the user. It is made of machine-washable polyester webbing and can be used on a shower chair. The belt mounts on the wheelchair or shower chair with a screw (models 4183 and 4183L), rear removable buckle (4220),
Positioning Belt (Buckle Type) (Model 92133040)
The Positioning Belt (Buckle Type), model 92133040, is a wheelchair seat belt designed for use by individuals with mobility and lower extremity disabilities or spinal cord injury. The belt is adjustable and constructed of black nylon webbing with a metal buckle. The seat belt mounts to the wheelchair back at waist level, and it includes attaching hardware. DIMENSIONS (LxW): 36 x 2 inches.
Posturetex-Multiway Cushion
Posturetex-multiway cushion is designed for individuals with limited mobility and use a wheelchair or a scooter for mobility. It is a versatile cushion featuring a 2 inch nodular foam base as well as a 2 inch nodular foam back which can be folded in half to make a 4 inch base cushion. The 2 inch base cushion is available with standard or coccyx cut out. Covered in black jacquard velvet which is removable for machine washing and a carry handle easy transportation. Spare covers are also available
Power Base Recliner Seating System
Power recliner designed for Everest and Jennings Lancer, Fortress 655 FS, Invacare XT powered wheelchairs, Quickie P-300, and Permobile Max90 & Super 90. Assembled; systems include reclining frame, rigid seat, rigid or sliding back, complete armrest and legrest assemblies, arm and leg troughs, standard headrest, toggle switch to control recline, and mounting interface to wheelchair. Rigid back 16 inches to 25 inches, sliding back 19 inches to 25 inches in one inch increments. Underseat 24 Vo
Power Buddy
The Power Buddy is a USB charger for powered wheelchairs and wheelchair light designed for use by individuals with lower extremity, mobility or severe physical disabilities. The unit plugs into the charger port of the wheelchair controller and enables the user to charge cell phones, MP3 players, tablet computers, and other USB devices while in the wheelchair. A universal USB adapter is included. The unit is equipped with a flexible gooseneck to enable positioning to meet the user's needs. The un
Power Chair Cover (Model 0129)
The Power Chair Cover, model 0129, is a wheelchair cover designed for use on powered wheelchairs. Made of weather-resistant nylon, the cover features elasticized, reinforced seams that fit the cover to the powered wheelchair. There are grommets along the bottom edge if the cover needs to be tied down. A cover storage bag is included. DIMENSIONS (HxLxW): 32 x 35 x 23 inches. COLOR: Black. WARRANTY: One-year limited warranty.
Power Chair Joystick Cover (Model V2200)
The Power Chair Joystick Cover, model V2200, is a powered wheelchair control cover designed for use by individuals with severe physical or mobility disabilities or spinal cord injury. Made of urethane covered water-resistant nylon with a transparent plastic panel over the joystick, this cover fits around the controller to protect it from dirt and moisture while still allowing use. DIMENSIONS (HxWxD): 14 x 5 x 4 inches.
Power Recliner Interface (Model 3350)
Used in conjuction with a Multimode Interface to permit operation of a power recliner by the same actuator used to operator the wheelchair. Multiple Power Recliner Interfaces may be used to independently operate multiple recliner functions. A toggle switch is provided to select either latching (continous) or momentary recliner operation, and separate up and down speed adjustments are provided to adjust the rate of recliner movement.
Powerchair Quick Modification
CUSTOM ADAPTATION PURPOSE: To make a powered wheelchair shorter for use under existing tables. Replace the existing front casters with roller blade casters and the rear drive wheels with smaller drive wheels. DIMENSIONS: The front casters are 4 inches in diameter (104 millimeters) and the replacement rear wheels are 8 x 3 inches. WEB SITE: http://www.wheelchairmodifications.org. REF: Powerchair Quick Modification. Wheelchairmodifications can also be reached at 5533 A Pony Farm Drive, Richmond,
Powered Elevated Chair
CUSTOM ADAPTATION -- PURPOSE: To provide a customized lifting chair for an individual with mobility disabilities that can be easily moved throughout a residential setting, including going through doorways. The chair has a U-shaped base made of rectangular hollow steel with a vertical post at the back, and large casters on the front ends of the U and smaller ones at the back. There are also larger bike-type wheels on either side which can be used to propel the chair if necessary. Additionally, th
Powered Wheelchair Footrest
CUSTOM ADAPTATIONPURPOSE: To enable an individual with multiple sclerosis and severe footdrop to use a wheelchair without assistance. The woman is unable to lift her feet up to conventional footrests. A pair of powered footrests were designed and fabricated using automobile power window motors and switches. The footrests detach when not needed and
can be mounted on the wheelchair while the user is seated in it. Both footrests lower to ground level, enabling the user to slide her feet on or off.
Powertech Vent Power Center
The PowerTech Vent Power Center is a portable ventilator power adapter for powered wheelchair designed for use by wheelchair users with respiratory disabilities. This power converter allows a portable ventilator to be powered by a wheelchair's batteries, eliminating the need for separate ventilator batteries. It connects to all electric power wheelchairs, and provides clean, stable, and regulated DC power to the ventilator. The PowerTech Vent receives DC power from the wheelchair battery at 24 v
Profiler Mounting System
The Profiler Mounting System is a wheelchair mounting kit for communicators. This system mounts to wheelchairs, walkers, hospital beds, strollers, or tables. Lightweight and adjustable, the unit is available for mounting on square or round tubing (specify choice) and can be moved to the side with the lift of a single lever when not in use. This system accommodates most communicators and notebook computers. The unit supports up to 15 pounds. OPTIONS: A variety of mounting plates and release optio
Profiler-Lite Mounting System
The Profiler-Lite Mounting System is a wheelchair mounting kit for communicators or switch mounting hardware. This system mounts to wheelchairs, walkers, hospital beds, strollers, or tables with square, oblong, or round tubing. This system accommodates lightweight communicators and most switches and supports up to five pounds, including pressure on the device. The unit can be mounted on the right or the left side and the universal base mount can be adjusted 360 degrees from front to back and 180
Proportional Head Control
The Proportional Head Control is a powered wheelchair controller designed for use by individuals with mobility or severe physical disabilities or spinal cord injury. This headrest-based joystick enables the user to control a power wheelchair by rotating his or her head on a headrest pad. This controller is available for P&G electronic controls.
Proportional Head Control (Model 3500)
A proportional actuator consisting of a movable padded headrest and a control switch. Movement of the headrest is converted to directional commands required by the Multimode Interface for mode selection and oepration. During wheelchair operation, the proportional head control allows precise control of both speed and direction.
Protective Cover For Wheelchair Controls
CUSTOM ADAPTATION PURPOSE: To protect powered wheelchair controls from rain. See-through plastic covers were sewn with a slit in the top for access to the joystick. The covers function like bottomless boxes and fit snugly over the controls and the joystick anchors them in place. The covers were bound with bias tape in a color of the child's choice and decorated with glitter. The covers can be put on and removed as needed. TITLE: Under Cover. JOURNAL: TAD Journal. REF: Vol 22 no 1, Autumn 2002:
Public Aid Tray (Models 33050, 33051, 33052, & 33053)
The Public Aid Tray is a lap tray designed for use with wheelchairs. Made of transparent, unbreakable polycarbonate, this tray features an aluminum rim and hook-and-loop attachment straps. DIMENSIONS (WxD): Model 33050 fits 12-inch chairs and is 18 x 19 inches with a 12-inch wide torso cutout. Model 33051 fits 14-inch chairs and is 20 x 20 inches with a 13-inch wide torso cutout. Model 33052 fits 16-inch chairs is 22 x 21 inches with a 14-inch wide torso cutout. Model 33053 fits 18-inch wide cha
PunkinFutz PunkinPie Accessible Bag
PunkinFutz PunkinPie Accessible Bag allows users to style their positioning chair, wheelchair, transfer chair, transport chair, or bicycle with the water resistant, highly reflective bag with easy access wide-pull zippers.
Push & Transfer Glove
Push & Transfer Gloves are push gloves designed for use by manual wheelchair users. The glove has open fingers, a half thumb, and wrap-around design. Padded in palms and wrist, it is made of 100 percent leather with, and it is available with a leather or non-slip rubber grip surface. It has dual Velcro closure with 3 inches of Velcro to allow for a secure fit. COLOR: Black.
Push Ease Full-Finger Gloves
Push Ease Full-Finger Wheelchair Glove are push gloves designed for use to protect the hands of manual wheelchair users. These general purpose wheelchair gloves protect the most vulnerable areas of the hand from blisters and injury while propelling a wheelchair.The gloves have full fingers with gel padding at the most crucial areas of the hand and removal tabs to assist in taking gloves off. Machine washable. SIZES: XX Small, X Small, Small.
Push Ease Half-Finger Wheelchair Gloves
Push Ease Half-Finger Wheelchair Gloves are push gloves designed to protect the wearer's hands while propelling a wheelchair. These gloves have gel-padded palms, partial finger coverage, and removal tabs to assist in taking gloves off. The gloves are machine-washable. SIZES: Small for hands 2 5/8 to 3 1/8 inches wide, medium for hands 3 1/8 to 3 5/8 inches wide, large for hands 3 5/8 to 4 1/8 inches wide, extra large for hands 4 1/8 to 4 5/8 inches wide.
Push Gloves/Quad cuffs
The Push Gloves/Quad cuffs are leather wheelchair push gloves designed to protect the hand from callouses and cuts. The cuffs are designed to assist the user to get where they are going efficiently and safely. The push gloves are made from soft but durable leather with a thick flexible textured palm material. The gloves also open fully along the back to allow the user to put them on easily, simply locate the thumb in the right place and close the velcro. This is an improvement over other designs
Push Handle Extensions
CUSTOM ADAPTATION PURPOSE: To enable a tall parent to push a child's wheelchair. The existing pish handles were sawed off the chair and new ferrules were fixed inside the exposed tubes with Loc-tite. Two new L-shaped handles were fashioned from metal tubing and one end of each was fitted into the new ferrules. The new handles were painted red to match the rest of the chair and finished with rubber bicycle-style handgrips. TITLE: Bicycle and Beyond. JOURNAL: TAD Journal. REF: Volume 26, Number
Pushon Treadmill
The PushOn Treadmill is a treadmill for wheelchair designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The user can roll onto the treadmill's low profile deck using a removable ramp, and attach the wheelchair to two safety straps. Speed ranges from 0 to 15 miles per hour and grade ranges from 0 to 15%. Cadence feedback is also available on the display screen. In addition to people seated in wheelchairs, this treadmill also can be used by individua
Pushtracker
---- PROTOTYPE --------- PURPOSE: To create a prototype tracking device (PushTracker) to monitor activity levels of individuals with lower extremity and mobility disabilities, spinal cord injury and others who use manual wheelchairs. The PushTracker allows manual wheelchair users to monitor their activity on an hourly, daily, and monthly level and includes data on average cadence, push distance, and total number of pushes. This device allows a manual wheelchair user to measure how he or she push
Quad Care Attaching System (Model 31878)
The Quad Care Attaching System, Model 31878, is lapboard mounting hardware for use by people who are quadriplegics or who have upper extremity disabilities. The kit allows the user to attach a tray or lapboard to wheelchair armrests by using clear vinyl thumb loops to streetch elastic bands over baked epoxy metal attaching pegs. The elastic loop stretches around the armrest and the pull-ring hooks onto metal bracket. The kit includes elastic loops, vinyl pull-rings, and metal brackets with atta
Quad Glove (Model Qg01)
The Quad Glove, model QG01, is a push glove designed for use by individuals with spinal cord injury or severe physical disabilities. This wheelchair glove opens up, allowing fingers to slide right in, and folds over the hand, securing with Velcro. Especially designed for wheelchair use, it features drum-dyed leather, soft enough for flexibility, yet strong and durable for tough wear. It extends up to the inside of the wrist to protect this sensitive area and is padded in all critical areas with
Quad Gloves With Rubber Palms
Quad Gloves are push gloves designed for use by individuals who use manual wheelchairs. These fingerless gloves fully open, enabling the fingers to slide in, folds over the hand, and secures with Velcro. The drum-dyed leather gloves are flexible and extend up the inside of the wrist for added protection and are padded with closed-cell foam at critical areas to prevent friction burns and nerve irritation. Technologically advanced rubber is sewn into the palms for gripping and protection. SIZES: E
Quad Push Cuff
Quad Push Cuffs are rubber crepe fingerless gloves with thumb flaps and a Velcro closure. The material covers the heel of the hand and the base of the thumb. SIZES: Universally sized (one size fits all); may be trimmed with scissors.
Quad-Link Retractable Mount.
The Tarsys Quad-Link Retractable Mount is a joystick holder designed to provide wheelchair users with broader access to tables and desks. This link system allows the user to independently retract and move the joystick nine inches back from its normal driving system. It is also designed to maintain correct joystick orientation to allow the user to maneuver the wheelchair with the joystick in a fully retracted position. The link system is adjustable in order to accomodate the strength and ability
Quick Caddy Beverage Holder
The Quick Caddy Beverage Holder is a wheelchair drink holder or cup holder designed for use by individuals who use wheelchairs or walkers. This device consists of a strong stainless steel cage which mounts on any vertical or semi-vertical tube, rail, or pole using the attached flexible plastic mount with a hook-and-loop strap. The product comes with a foam "cozy" which securely holds soda cans or small water bottles. Without the cozy, the cage can carry larger 16-ounce glasses or larger water bo
Quick Release Back (Model 102-7000)
Solid back insert, 1/2 inch marine grade plywood, 1 1/2 inches of foam padding, naugahyde upholstery. Quick release brackets fit 3/4 inch, 7/8 inch and 1 inch tubing. Bracket has a latch that pivots for easy quick release. Comes with multi-adjustable brackets. Backs are cut to fit between the rails.
Quick Release Mount (Model Qrm-2)
The Quick Release Mount, model QRM-2, is an accessory for mounting communication devices on wheelchairs. The mount holds the device firmly, yet allows removal with a flip of a lever. The mount is standard on most Prentke Romich mounting systems. OPTIONS: Adapters are available for Prentke Romich devices that use mounts from earlier wheelchair communication mounting kits, or any other mounting system using a 7/8 inch bar.
Quick Release Seat (Model 101-7000)
Solid seat, 1/2 inch marine grade plywood and 1 1/2 inches of foam padding, naugahyde upholstery. Quick release brackets fit 3/4 inch, 7/8 inch and 1 inch tubing. The bracket has a latch that pivots for easy quick release. Seat comes with multi-adjustable brackets. Seats are cut to fit between the rails.
Quickie Padded Wheelchair Pelvic Belt
The Quickie Padded Wheelchair Pelvic Belt is designed to prevent wheelchair users from sliding in the wheelchair. The Premium Quickie padded wheelchair seat belt. Airline style flip buckle is easy open and has a d-ring pull to tighten. The device is very durable and has 2-inch webbing adjusts to most all user sizes. Wide pads afford greater comfort and contact. Includes nylon bolt plate with 1/4 inch hole and adjustable tri-glide to easily adjust desired length. The belt clamps are easy to attac
Quik Mount (Model M1015)
The Quik Mount, model M1015 is a mounting clamp designed for attaching head supports to wheelchairs. This bracket provides a quick and easy way for clinicians to attach head supports to wheelchairs for evaluation purposes. It can also be used on chairs that have sling style back upholstery.
Racing Wheelchair Stabilizer
DO IT YOURSELF ENTRY --- PURPOSE: To facilitate transferring a child to a racing wheelchair. The unit has a plywood base with a pipe frame at the front to hold the front wheel; the front wheel is further secured with a Velcro strap. This stabilizes the racing wheelchair for ease of transfers in and out with one person assisting. The half-inch thick plywood base is made to the size of the wheelchair, and excess material is removed to create a lighter weight base. The pipe frame consists of one-in
Ram Mounts Ez-On/off Flexible Seat Clamp Mount
The RAM Mounts EZ-ON/OFF Flexible Seat Clamp Mount is a stand for a tablet computer, cell phone holder and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This mount consists of a universal mount with clamp and 2.5-inch diameter ball base, an 18-inch flex rod, a single socking mounting system, and a custom high strength composite non-locking cradle holder for the
Ramp To Tilt Wheelchair To Comfortable Eating Position
CUSTOM ADAPTATION PURPOSE: To enable an individual with cerebral palsy who uses a wheelchair with tilt-in-space seating to eat independently. The user's disability prevents upright sitting, so a low-level ramp was constructed to raise the wheelchair's rear wheels. Seventeen millimeter lightweight plywood was used to construct the sloping portion of the ramp, and five slats of 50 x 25 millimeter wood were used to fashion a gutter to hold the rear wheels in place. The same type of wood was used t
Recharge
The ReCharge is an alternative power connection for powered wheelchairs designed for use by people with lower extremity or mobility disabilities, spinal cord injury and others who use a powered wheelchair. It is intended to help a wheelchair user to more easily connect the powered wheelchairto a battery charger. This product features a long mast topped with a large circular handle that drops into a socket mounted on the wheelchair. The unit can be used with sockets mounted for the ReJoy or JoyBa
Reclining Arms (Models 07-A & 07-B)
Arms attach to backpost of reclining wheelchair to maintain a position relative to the position of the body when reclined. Allows chair controls to move with the arms during the recline. LaBac Systems arm troughs and pads can be mounted on the arms. Arms are strong enough to hold a lap board. Model 07-B ($395) features a quick release mechanism which allows instant removal of armrests.
Recluse
The Recluse is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This wheel has a twin bent Gothic spoke design that is repeated 5 times around the wheel to resemble a 10-legged spider sitting in the wheel. The wheel is available with a mirror-polished finish or in any of 5 anodized colors, allowing the wheels to be coordinated with the wheelchair frame. The wheel is CNC precision machined from aircraft quality aluminum
Rehadesign Gel-Palm Wheelchair Gloves
RehaDesign Gel-Palm Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Designed to diminish impact force to the hand, these wheelchair gloves have half fingers and an enclosed thumb and are made from quality soft leather with gel padding built into the palm. They have a terry sweat-wipe backing. SIZES: Small, medium, large, and extra large.
Rehadesign Ultra-Grrrip 4 Seasons Wheelchair Gloves
RehaDesign Ultra-Grrrip 4 Seasons Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Suitable for all-weather use, these full-fingered leather gloves have a textured palm for improved grip. SIZES: Small, medium, large, and extra large.
Rehadesign Wheelchair Tire Covers
RehaDesign Wheelchair Tire Covers are wheelchair tire covers designed for use by individuals who use wheelchairs. Also known as wheelchair slippers and esigned to prevent tracking in dirt and debris from the wheels, these covers stretch to fit standard wheelchair rear wheels. They can cover the tire only or the tire and the handrim. The can be put on without leaving the wheelchair and can also be used to protect wheels and handrims from damage during transport. They have a soft artifical suede f
Rehadesign Wheels On Fire Spoke Reflector
RehaDesigns Wheels on Fire Spoke Reflectors are reflectors for wheelchair spokes designed for use by individuals who use wheelchairs. These reflectors are designed to increase visibility at night. These reflectors snap on to spokes up to two millimeters in diameter.
Rehadesigns Spoke Guards
RehaDesign Spoke Guards are spoke protectors designed for use by individuals who use wheelchairs. Designed to protect fingers from the wheel spokes, these screen-printed guards attach with a choice of 12 nylon zip ties or 12 snap-on connectors (both included). The spoke protectors are available in a choice of five designs: butterflies, puppies, kittens, planets, or woman. DIMENSIONS: Available for 20-, 22-, or 24-inch wheels.
Rejoy
The ReJoy is a powered wheelchair controller designed to enable powered wheelchairs to be controlled with a joystick positioned in the front of the seat at the midline rather than on the right or left armrest. The ReJoy utilizes a Center Drive System that consists of mounting hardware and a socket that can be mounted in three positions: in front of the seat on the center line; on the side beneath either armrest; or in the back of the wheelchair. When mounted on the side, the mast with the contro
Releasing Wheelchair Hubs
Heavy duty, wheelchair hubs, provide quick change of wheels or release for transport by pushing one button on outside end of hub. Aluminum flange for spokes, 48 mm. Standard 36 holes or other spoke drillings. Built for 14 gauge light spokes, larger drilling available for heavier spokes. Precision ball bearings, permanently adjusted and lubricated, waterproof.
Removable Commode (Model 90)
The Removable Commode, model 90, is a commode seat attachment for wheelchairs. It come with a removable solid insert with a cushioned cover to placed on top of the commode when not in use. The pan is removable from the back. DIMENSIONS: Fits 16- and 18-inch wide chairs.
Reps Wheelchair Gloves (Model Wh-1)
REPS Wheelchair Gloves, model WH-1, are push gloves designed for wear by wheelchair users. These gloves have three-quarter length fingers and thumb and are made of tough suede padding to protect the hand's main contact points with the wheel. The gloves have terrycloth lining on the inside of the palm for additional protection and comfort.
Reps Wheelchair Gloves (Model Wh-2)
REPS Wheelchair Gloves, model WH-2, are push gloves designed for wear by wheelchair users. These gloves have a three-quarter length thumb and no fingers. Made of soft leather with a nylon spandex back, these gloves have tough suede padding to protect the hand's main contact points with the wheel and a terrycloth lining on the inside of the palm for additional protection and comfort. SIZES: Small, medium, large, or extra-large. COLOR: Black.
Reps Wheelchair Gloves (Model Wh-4)
REPS Wheelchair Gloves, model Wh-4, are wheelchair push gloves designed for use by individuals with limited hand mobility. These wrap-around gloves are made of durable suede leather with padding to protect the hand's main contact points with the wheel.
Reps Wheelchair Gloves (Model Wh-5)
The Reps Wheelchair Gloves, model WH-5, are wheelchair push gloves designed for use by individuals who use wheelchairs. These gloves have full-length fingers and thumb and are made of durable suede leather with padding to protect the hand's contact points with the wheel.
Resident-Release Three-Point Wheelchair Belt (Models 610210 & 610215)
The Resident-Release Three-point Wheelchair Belt is a wheelchair seatbelt designed to provide security and positioning assistance. This automotive style-belt is a combination lap and shoulder belt that secures to the wheelchair using the existing screws. Model 610210 has side-release buckle closure and model 610215 has a user-friendly buckle. SIZES: One size fits most.
Retractable Headrest System (Models 06-1 & 06-1S)
Retractable headrest system for high quad power recliners. Headrest moves to natural position for support and retracts compactly behind back when not in use. Replaces spreader bar for back stability. Has infinite height adjustment on back. Power recliner and head rest can be activated with common switch with available interface. 24 volt DC gear motor with overload protection. Available for all makes and models of reclining wheelchairs. Model 06-1 is for standard back; Model 06-1S is for sliding
Retracting Joy Stick.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Retractable joy stick control box for a powered wheelchair to allow the chair to be positioned near a table. Briefly describes a springloaded automatic joy stick box retractor which permits the box to recede as it makes contact with the table and return to its normal position when the wheelchair is backed away. Principal investigator: Theresa Ackerman, Georgia Tech University. SKILLS REQUIRED: Mechanical Engineering. TITLE: Retracting Joy Stick JOURNAL
Retro Swing Armrest Bracket
The Retro Swing Armrest Bracket is a wheelchair armrest bracket that will convert a fixed armrest that attaches to the seat back frame to a lateral swing away armrest. It is designed for use by people with lower extremity or mobility disabilities or spinal cord injury and others who use a manual or power wheelchair. This system allows the armrests to swing up to 270 degrees horizontally. This can be particularly useful for form-fitting curved trunk laterals and wide armrest pads, as well as for
Retroback
The Retroback is a foam wheelchair back support designed for use by individuals with mobility, neurological, or lower extremity disabilities or spinal cord injury. This cushion is lightweight and durable and is equipped with a chrome-plated steel clip that attaches to the existing sling upholstery. Removing the Retroback is done by simply lifting it off the upholstery. The cushion also features a nylon/polyester water-resistant, machine-washable cover. DIMENSIONS: Available in 16, 18, or 20 inch
Retrolift
The RetroLift is an elevating seat attachment for a wheelchair designed for use by people with lower extremity and mobility disabilities and spinal cord injury and others who use a wheelchair. It will vertically raise a person seated in a wheelchair up to 17 inches. This product securely attaches to any conventional wheelchair without any special tools, and it comes equipped with a back support, armrests and a plush 2-inch thick cushion. A flat seat pan with Velcro strips is also available to if
Rhino Tray (Models 11A & 11B)
The Rhino Tray, models 11A and 11B, is a wheelchair lapboard and work tray for children and adults with lower extremity and mobility disabilities, spinal cord injury, and others who use wheelchairs. PolyLock Fasteners incorporated in design eliminating the need for screws or bolts in the tray surface.. Corners and edges are fully rounded for safety, and the tray tops can be snapped off in an emergency. Custom stomach and control box cutouts available. OPTIONS: Available with Telescoping Mount Ha
RibGrips Advanced Wheelchair Handrims/Push Rim
The RibGrips Advanced Wheelchair Handrims/Push Rim are designed for wheelchair users to push their wheelchair with more ease and comfort. The ergonomic/responsive soft rib discs increase performance and decrease fatigue. RibGrips also work well in snow and light rain.
Rio Mobility Dragonfly Attachable Handcycle
The Dragonfly™ is an attachable handcycle for use by individuals with mobility issues. The Dragonfly attaches to most wheel chairs.
Ergonomic hand cranks fit a wide range of riders and facilitates maneuverability for the user. Built-in coaster brake lets users control speed without removing hands from the handle. The secondary brake lever has a parking feature that keeps chair in place.
RoboCup
The RoboCup is a patented portable holder designed for use by people who use a walker, wheelchair or mobility scooter and other individuals with a disability that affects their ability to hold or grasp objects. This portable dual caddy can securely hold two drinks, two fishing poles, tools, gear and personal belongings such as a telephone, keys, glasses and flashlight. The unit attaches to wheelchairs, walkers, scooters, grab bars, hospital beds or golf carts using the integrated clamp. The Robo
Rock’n Roller
---- PROTOTYPE --------- PURPOSE: To create a prototype of a motorized sensory platform for a high school student with shaken baby syndrome to allow her to enjoy movement and music independently. The young woman has severe cognitive, visual, and physical disabilities and poor muscle coordination. She can only voluntarily control her head and right hand. She spent most of her time in a manual wheelchair and was unable to propel herself. Her teachers were unable to give her constant 1-on-1 attenti
Rocking Chair Adapter For Wheel Chair
CUSTOM ADAPTATIONPURPOSE: To make it possible for a wheelchair to absorb the shocks from the involuntary backward and forward movements of a girl with cerebral palsy. This girl has broken parts of her chair several times previously. Instead of building a special rocking chair, it was decided to convert the wheelchair itself into a rocking chair. A device was built using 6-millimeter thick aluminium plate rolled to a suitable curve. The chair can be rolled onto the device and tied down. The devic
Rockstar Guitar Stand
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a customized guitar stand that attaches to a wheelchair for an adult male with cerebral palsy. The Rockstar guitar stand provides a safe and durable attachment for the user’s wheelchair which supports his electric guitar and keyboard. The device attaches to the armrest supports of the wheelchair and allows for adjustment of the guitar platform to the most comfortable position for the user. When brainstorming design ideas it was decided that
Roho Cushion Retainer
Nylon mesh and webbing device fastened into existing wheelchair seat and back upholstery screw locations to keep cushion from sliding back on seat. Adds very little weight to chair. Designed to fit most standard size wheelchairs.
Roho Universal Cushion Cover With Pocket
The Roho Universal Cushion Cover with Pocket is a cushion cover with under seat pocket designed for use by wheelchair users. The cover has a durable stretch Lycra top and the side material is three-layer knit polyester spacer fabric which provides air circulation and cools the user. The attached pocket can be used to store small items such as wallets, keys, glasses, or coins. DIMENSIONS (HxWxD): Available dimensions range from 11 to 18 x 11 to 18 x 1 to 4 inches. WARRANTY: 6 months.
Roll Out Trackway
Roll Out Trackway is a portable rubber track designed for individuals with limited lower extremity mobility as a result of cerebral palsy, stroke, Parkinson’s disease or multiple sclerosis. The Roll Out Trackway can be rolled out over uneven surfaces to provide access for both wheelchairs and pedestrians. It can be cut to length and can be trimmed to fit around steps, corners, or other obstacles. When not in use, Roll Out Trackway can be rolled up for storage.
Rolyan Slide-On Adjustable Lap Tray (Model A707001)
The Rolyan Slide-On Adjustable Lap Tray, model A707001, is a molded-plastic lapboard designed for use by individuals who use wheelchairs. This tray is equipped with bases that fit over the upholstered armrests of a wheelchair to help prevent tipping. The tray is designed to fit wheelchairs from 16 to 20 inches wide with standard or desk-length arms. The bases can be adjusted to fit with an allen key. OPTIONS: Back strap, model A3173. DIMENSIONS (WxD): 23.5 x 21.5 inches
Rolyan Workhard Open Finger Glove (Models A38257 To A38268)
The Rolyan Workhand Open Finger Glove, models A38257 to A38268 is a glove designed to absorb shocks and vibrations for persons with arthritis or other neurological disabilities. Constructed of leather with Sorbothane lining and a Lycra back side, the washable glove is available for the left or right hand. SIZES:: To determine size, make a loose fist and measure the circumference of the hand just below the knuckles. Extra extra small is up to 7 inches wide; extra small is 7 1/8 to 7.75 inches wid
Rotational Seating System
Seating system rotates in space to 45 degrees, maintaining seated position. For Everest & Jennings and Invacare sectional back, recliner, and powerbase (Lancer, XT). Rotating frame, rigid seat, rigid back, standard headrest, complete armrest and legrest assemblies, arm and leg troughs, underseat module mount standard. Toggle switch control. Legs elevate manually. Back heights up to 25 inches in one inch increments. Underseat 24 volt DC actuator, and bearings on all moving parts. Options: sem
Rough Terrain Guidance System For Powered Wheelchairs
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted wheelchair terrain sensing control system for individuals with mobility disabilities, spinal cord injury and other people who use wheelchairs. This adaptation was inspired by the needs of disabled veteran's for independence and mobility. By using terrain sensing control systems designed for the guidance of autonomous vehicles on the battlefield, researchers at Florida A&M University-Florida State University College of E
Round Mobility Clutch
The Round Mobility Clutch is a carrying bag designed for use by individuals with lower extremity, mobility, balance and walking disabilities. This oval carrying bag attaches to most canes, walkers, crutches, and wheelchairs or transport chairs with two hook-and-loop straps. The bag has an outside easy-access pocket that features an elasticized top and an interior zippered pocket for storing items such as keys, cell phones or other small items. The bag easily detaches and can be worn on the wrist
Rowheel
---- PROTOTYPE --------- PURPOSE: To design a prototype wheelchair design to reduce repetitive-stress injuries of wheelchair users and those with mobility disabilities. The Rowheel is a manual wheelchair wheel designed for use by people with mobility and lower extremity disabilities or spinal cord injury and others who use a manual wheelchair. Rowheels use "planetary gears" configured to allow the wheels to rotate counter to the hand rim. This allows users to pull on the hand rim to go forward.
Rowheel
---- PROTOTYPE --------- PURPOSE: To design a mechanism used to modify wheelchairs so that the chair is propelled by a pulling action of the arms rather than by pushing for individuals with mobility disabilities and spinal cord injuries. The design is based on the premise that allowing the stronger biceps take on more of the work will result in more endurance and greater control. The Rowheel has similar specifications and appearance to existing manual wheelchair wheels, and the Rowheel is design
Safe T Spin For Disabled Awareness (Model Da-50)
The Saf T Spin for Disabled Awareness, model DA-50, is a safety flag designed for use by individuals who use wheelchairs. This warning signal draws attention to wheelchairs by adding height and motion. Atop a fiberglass rod that attaches to a wheelchair, this rotating signal carries the wheelchair disability and can be seen over the rooftops of vehicles while the wheelchair is crossing intersections or parking lots. A fitting in the middle of the fiberglass rod allows for assembly and disassembl
Safe•t Mate Adjustable Front Anti-Tippers (Model Sm-011)
Safe•T Mate Adjustable Front Anti-Tippers, model SM-011, are anti-tipping attachments designed for use on wheelchairs. These anti-tippers have five height adjustments to accommodate wheelchairs from full height chairs to low hemi chairs. The attachment is made from powder- coated steel tubing and heavy-guage chrome- plated steel with easy gliding wheels. Mounting hardware and installation instructions are included. DIMENSIONS: These anti-tippers fit chairs with frame tubing 7/8 or 1 inch in diam
Safe•t Mate Alarmed Velcro Seatbelt (Models Sm-005 & Sm-005L)
The Safe•T Mate Alarmed Velcro Seatbelt is a wheelchair seatbelt and wandering patient alarm designed for use by wheelchair users with Alzheimer's disease or cognitive disabilities. This Velcro lap belt has a alarm that sounds when the belt is separated to alert caregivers and remind the user to remain seated. The nylon belt features a bright red pull strap to facilitate locating and releasing. The alarm box features a heavy duty on/off switch and a stainless steel universal mounting clip. Horn
Safe•t Mate Sm2 Anti-Rollback Device
The Safe-T Mate SM2 Anti-Rollback Device is an anti-tipping attachment designed for use by individuals who use wheelchairs. This device prevents a wheelchair from rolling back by grabbing the tires as the user attempts to sit or stand. The seat pad has three height adjustments for regular, hemi, and extra-low chairs. The articulating/floating pad moves forward to accommodate users who slouch in their chairs while remaining in proper alignment with the seat bottom. This device is compatible with
Safe•t Mate Universal Fit Rear Anti-Tippers (Model Sm-008)
Safe•T Mate Universal Fit Rear Anti-Tippers, model SM-008, are anti-tipping attachments designed for use by individuals who use wheelchairs. These rear anti-tippers have sliding height adjustment allowing them to fit various makes and models of chairs and to be positioned at different heights. These anti-tips are made from solid bar stock with gliding wheels. Their height is infinitely adjustable within a 10-inch range. DIMENSIONS: 2 foot diameter wheels. WARRANTY: Guaranteed for one year from
Safe•t Mate Wheelchair Labeling System (Model Sm-003)
The Wheelchair Labeling System, model SM-003, is a wheelchair labeling system designed for use on wheelchairs used in facilities with multiple wheelchair users. This product allows staff to manage user-specific wheelchair accessories, such as leg rests or lap cushions. Each chair can be outfitted with a flexible plastic bracket that has a vinyl label. Each label contains spaces for the user name, room number, chair accessories and total chair weight. Each unit contains a set of 10 brackets with
Safety Flag
The Safety Flag is a wheelchair safety flag designed for use by individuals who use power wheelchairs. Designed with extended shaft height coupled with the flag’s high-visibility color and logo, this safety flag is intended to increase visibility while using powered wheelchairs in busy areas or areas that are poorly lit. The flag is made of durable vinyl and is easily removed when not in use. DIMENSIONS: The shaft is six feet long. COLOR: The flag is orange.
Safety-Soft Security Belt (Models Mdt822125 & Mdt822126)
The Safety-Soft Security Belt is a wheelchair seatbelt designed for use by individuals with cerebral palsy, mobility or neurological disabilities, or spinal cord injury. This seatbelt helps keep wheelchair users upright. The belt has a polyester strap with a thick foam lining to reduce friction on the user's hips. It has bar tacks at stress points and is washable. The one-piece style (model MDT822125) is a single piece of foam that ties behind the back. The two-piece style (model MDT822126) has
Samba
The Samba is an adjustable hi-low, tilt-in-space chair that offers a unique midline support system for children requiring moderate to higher levels of postural control, suitable for both home and school. The midline support system incorporates a 4 point pelvic strap that corrects the position of the pelvis. This improves alignment and helps prevent rotation and backward tilt. The modular system also eliminates the need for knee blocks. Height, width and angle adjustments can all be made easil
Sammon Preston Side Pouch For Wheelchair (Model 6441)
The Sammons Preston Side Pouch for Wheelchair, model 6441, is a wheelchair side pouch designed for use by wheelchair users. Designed for full length arm rest only, this pouch features a blue denim or black vinyl side pouch with full length zipper and 2 large side pockets. DIMENSIONS (HxW): 6 x 13 inches.
Sammons Preston Arm Tray With Foam Elevator (Model A7464)
The Arm Tray with Foam Elevator, model A746-4, is a plastic arm support and trough for use by people with upper extremity disabilities who also use wheelchairs. The unit includes a washable soft foam insert for cushioned elevation that can be trimmed and customized for individual needs. The tray includes straps for attaching the arm tray to the wheelchair. OPTIONS: Replacement foam inserts, model A746-5, are available for use with this or other Smith & Nephew Arm Trays.
Sammons Preston Bright Brakes (Model 6503)
The Bright Brakes, model 6503, are globe-shaped wheel lock extension levers designed for use on wheelchairs of individuals with low vision and grasping disabilities. The size and color of the brake extensions increases visibility while providing a comfortable and easy-to-hold grip. These extensions fit all standard tubular brake extensions (brake extensions sold separetely). COLOR: Blue, teal, or gold metallic finish (no color choice).
Sammons Preston Cup And Holder For Wheelchair (Model 1139)
The Sammons Preston Cup and Holder for Wheelchair, model 1139, is a wheelchair drink holder with cup designed for use by individuals who use wheelchairs. This device attaches to most wheelchairs, canes, and walkers. The unit features a cup with large open loop handle, snap on lid with opening, and two plastic coated spring clips for mounting. Once the attachment clip is installed onto the chair, the cup holder itself can be removed as needed. The cup holds up to 8 ounces of liquid and is dishw
Sammons Preston Elevating Arm Tray Kit
The Sammons Preston Elevating Arm Tray Kit is an arm trough and arm posiiitioner designed for use by wheelchair users who must keep one arm elevated. The tray straps to right or left standard or desk-length wheelchair arms with Velcro and includes a washable foam insert contoured to keep the users arm in the proper position. The unit can be cut to the desired length. OPTIONS: An extra pair of foam elevating inserts ($18.95). DIMENSIONS (LxW): 22 x 4.5 inches. COLOR: The foam is light beige.
Sammons Preston Flipaway Armrests (Models 604401 & 604402)
Th Sammons Preston Flipaway Armrest, models 604401 and 604402 is a armrest designed for use by individuals who use wheelchairs or other seating systems. Features include a heavy duty hinge that allows the arm rest to flip up and out of arms way, a three-inch recess that serves as a beverage or ashtray holder, and a one-inch black vinyl foam padding. The armrest can also be used as a work surface or for transporting small items. Model 604401 is designed for right side attachment and Model 604402
Sammons Preston Hardwood Transfer Board (Models 6113 & 6114)
The Maple Transfer Board models 6113 and 6114 are transfer boards designed for use by people with mobility disabilities. The boards features a highly lacquered finish and tapered ends. DIMENSIONS (DxLxW): Model 6113 is .75 x 24 x 8 inches and model 6114 is .75 x 30 x 8 inches. Both models taper to 1/8 inch at the ends. COLOR: Natural maple.
Sammons Preston Leg Rest Bumper For Wheelchairs (Model A748310)
The Leg Rest Bumper for Wheelchairs, model A748310, is a leg rest pad designed to protect the legs of wheelchair users from coming in contact with leg rest hardware. Made of foam laminated with a hook-and-loop-responsive soft material, these bumpers can be wrapped around leg rest uprights and other areas and can be trimmed to fit. DIMENSIONS: 4 x 15 inches.
Sammons Preston Mini Wheelchair/walker Pouch
The Sammons Preston Mini Wheelchair/Walker Pouch doubles as a carrying bag for a walker and a wheelchair side pouch for use by people with mobility disabilities. The machine-washable nylon pouch snaps over the front walker bar or hangs from the wheelchair armrest. DIMENSIONS (WxH): 10 x 8 inches. COLOR: Gray.
Sammons Preston Modified Deluxe Wheelchair Arm Tray (Model A74612)
The Sammons Preston Modified Deluxe Wheelchair Arm Tray, model A74612, is an arm trough designed for use by individuals who use wheelchairs. Features include a cut-away attachment base designed to allow access to wheelchair brakes while supporting the full length of an arm. The tray can fit either a standard or desk arm chair, and can be used on either the right or left side. Kushionflex padding for comfort and protection is included. DIMENSIONS: The padding is 1/8 inch thick.
Sammons Preston Molded Clear Lap Tray (Model A7073)
The Sammons Preston Molded Clear Lap Tray, model A7073, is a tinted translucent lapboard designed for use by individuals who use wheelchairs. This tray enables the lower extremities to be completely visible. Made of high-impact Lexan, the tray features a molded rim and a recessed space for cups, glasses, bottles, or cans. The tray is equipped with D-ring hook-and-loop straps on the arms and a snap-buckle back strap that fastens on either side of the chair. The arm and back straps attach by threa
Sammons Preston Solid Seat Insert
The Sammons Preston Solid Seat Insert is designed for use in wheelchairs with sling seats. This semi-rigid closed-cell foam insert provides a firm, flat seating surface in sling seats. This surface also helps improve posture by helping to balance the pelvis and distribute weight over the hips and thighs. This insert is available in standard, narrow, or relaxed-fit styles. DIMENSIONS (WxD): The standard model is 18 x 16 inches, the narrow model is 16 x 16 inches, and the relaxed-fit model is 20
Sammons Preston Universal Wheelchair Arm Tray (Model A7468)
The Sammons Preston Universal Wheelchair Arm Tray, model A7468, is an arm trough designed to position and provide arm support for individuals with upper extremity disabilities who also use wheelchairs. The trough features a plastic base that slides over the arm pad of standard or desk-length wheelchair arms and is designed for either the right or left side use. A Kushionflex pad is included to protect potential areas of irritation. The tray requires no tools for installation or removal. .DIMENSI
Sammons Preston Wheelchair Brake Lock Extension (Models 652402, 652403 & 552504)
The Sammons Preston Wheelchair Brake Lock Extension, models 652402, 652403 & 552504), is a wheel lock extension lever designed for use by wheelchair users with limited reach or arm strength. The chrome-plated steel lever is made of 0.63-inch round tubing and has a flat opening at one end to slip over the existing wheel lock; the other end has a rubber grip. The flattened end fits over standard brake lock and adds 11 inches. DIMENSIONS: 7.5 inches long.
Sammons Preston Wheelchair Elevating Arm Tray Kit (Model 6461)
The Sammons Preston Elevating Arm Tray Kit, model 6461, is an elevating armrest designed for use by individuals who use wheelchairs. Designed to fit most standard or desk armrests, this plastic tray fastens to the armrest of wheelchairs with a double D-ring Velcro Velstrap. The tray elevates to 25 degrees and can be mounted for either right or left side use. A heat gun can be used for customization. Bolts are included for elevation. DIMENSIONS (LxW): 22 x 4.5 inches. Double D-ring Velcro stra
Sammons Preston Wheelchair Foot Support (Model A7481)
The Wheelchair Foot Support, model A7481, is a foot support designed for use by people with weak, flaccid or hypertonic lower extremities who use wheelchairs. It positions the foot in proper anatomical alignment to assist in the prevention of ankle contractures. The foot portion effectively eliminates the need to continually reposition the foot and prevents feet from slipping off the wheelchair footrest. Made of rigid plastic, the support is covered to help prevent forward slippage and attaches
Sammons Preston Wheelchair Pouch
The Sammons Preston Wheelchair Pouch is a wheelchair back pouch designed to provide carrying capacity for wheelchair users. The expandable Codura nylon pouch is waterproof, stain-resistant, and machine-washable. It features a top cover flap and attaches to wheelchair push handles with loops. DIMENSIONS (WxHxW): 14 x 12 x 3 inches. COLOR: Gray.
Sammons Preston Wheelchair Pushing Cuffs (Model 9470 & 9471)
The Sammons Preston Wheelchair Pushing Cuffs, model 9470 and model 9471 are push cuffs designed to protect the palms and provide a better grip while propelling a wheelchair. The finger and thumb areas are open to permit full hand use at all times. The cuffs are secured to the hand with a leather strap and D-ring fasteners. Model 9470 are made of soft suede with non-slip Dycem palms, and model 9471 are made of plain suede. Model 9470 are $28.95 and model 9471 are $65.95. SIZES: One size fits all.
Sammons Preston Wheelchair Pushing Cuffs (Model 9470)
The Sammons Preston Wheelchair Pushing Cuffs, model 9470, are push cuffs designed to protect wheelchair user's hands and provide a better grip and traction while propelling a wheelchair. These suede leather gloves feature open fingers and thumb and a non-slip pad sewn into the palm. They slip on using a leather strap and D-ring closure. SIZES: One size fits all.
Sammons Preston Wheelchair Shopping Bag (Model 6444)
The Sammons Preston Wheelchair Shopping Bag, model 6444, is a wheelchair back pouch designed to carry groceries or large personal items for people who use wheelchairs. The bag features hook and loop fasteners that reduces bag’s 5-inch width if less room is needed. The material is latex free. DIMENSIONS (WxH): 16.5 x 16.5 inches.
Scooter Arm Tote
The Scooter Arm Tote is a wheelchair side pouch designed for use by individuals who use scooters. This heavy canvas bag attaches to the scooter armrest and features one large inner pocket with easy-to-grasp zipper closure and a three-section mesh outer pocket. DIMENSIONS: 10.5 x 13.5 x 2 inches.
Scooter Armrest Extensions
CUSTOM ADAPTATION PURPOSE: To assist an individual with mobility disabilities in transferring from a scooter. The existing scooter armrests were altered so they can be moved forward to provide a point of support in front of the user during transfers and moved back at other times. The armrests are mounted on hollow square tubing, into which long slots, rather than single holes, were cut. The arms slide along the slot into the forward position for standing transfers and backward for standard use
Scooter Basket Liner And Cover
The Scooter Basket Liner and Cover is a liner for scooter basket designed for use by individuals who use powered scooters. The protective cloth liner with cover fits inside a standard wire basket and holds shopping or other small items being transported in the basket. Items can be kept out of sight and dry by placing the included removable cover on top of the basket. The liner has carrying handles and an elasticized band that fits around the rim of the basket. The liner cover also features an el
Scooter Basket Liner Organizer (Model Ez0126)
The Scooter Basket Liner Organizer is a liner for a scooter basket designed for use by individuals with mobility disabilities or spinal cord injury. Made of nylon, the liner includes an adjustable drawstring to fit most baskets. There is a zippered front pocket for personal items (e.g. wallet, keys) and two mesh pockets to hold such items as cell phones, remote controls or beverages. DIMENSIONS (HxLxW): 11 x 13 x 10 inches. COLOR: Black.
Scooter Control Cover
CUSTOM ADAPTATION PURPOSE: To enable an individual with mobility disabilities to use a scooter outdoors in inclement weather. Made of Lexan, the cover is shaped to fit over the scooter controls without getting in the way. Initially, the cover was attached with Velcro strips glued to the back of the handlebar mount and the cover itself. However, the Velcro did not hold the cover in place when the user reached under to insert the key. The Velcro was replaced with cable ties laced through small ho
Scooter Trailer
The Scooter Trailer is a wheelchair cart designed to equip a powered scooter to tow a child and/or cargo. The trailer is mounted on a single swiveling castor wheel. The trailer is attached to the scooter by means of a fixed hitch. There is a wire basket on the trailer enclosing a bicycle baby seat which is mounted on a wooden platform. The fixed hitch/wheel castor configuration allows greater maneuverability when reversing. PROTOTYPE DEVELOPMENT: Designed by Jim Rees for mothers who use scooter
Sealed Lead Acid Batteries
Sealed Lead Acid Batteries are batteries designed for use with power wheelchairs. The rechargeable batteries are available in 23 leak-proof, maintenance-free models. The nominal capacity of the battery is a 20 hour rate according to types at 25 degrees Centigrade to a cutoff voltage of 1.75 volts per cell.
Sears Sealed Gel Cell Battery (Models 9613, 9616, & 9617)
The Sears Sealed Gel Cell Battery, models 9613, 9616, and 9617, is a wheelchair battery designed for use with powered wheelchairs and scooters. Designed for repeated discharging and recharging, these batteries are leak-proof and non-spillable. An automatic 12-volt charger charges the battery to at least 13.8 volts, but no more than 14.1 volts. The battery has an "L"-type terminal. The discharge rate is approximate 43 minutes at 25 amps, 83 minutes at 15 amps, and 170 minutes at 8 amps. GROUP/SIZ
Seasucker Ipad Mounting System
The SeaSucker iPad Mounting System is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system requires no bracket for the iPad; it has a 4.5-inch diameter vacuum mount that attaches to the back of the iPad. This mount attaches to a flexible RAM arm that can be moved to position the iPad as needed. The arm attaches to a second
Seat Belt Alarm
Seat Belt Alarm is designed for older adults and people with varying mobility disabilities. It can be attached to most wheelchairs or devices. The belt alerts staff or caregivers when the buckle is undone. The alarm has an on/off switch, low battery light, and flashing light to help locate the user. The belt has grommets to secure bolts for attaching to chairs. A mounting bracket is included for the alarm. Uses one 9V battery (included). Belt fully extended measures 50 inches (127 centimeters) e
Seat Belt Kit
The Seat Belt Kit is a wheelchair seatbelt designed for use with the Otto Bock MOSS II seating systems (see separate entries). The kit consists of webbing with a plastic side-release or push button-style buckle. DIMENSIONS: 1.5 and 2 inch widths.
Seat Belts
The Seat Belts are wheelchair seatbelts designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Available styles include auto-style belts and dual-pull belts with comfort pads. OPTIOS: Slide-on and sew-on comfort pads are available. DIMENSIONS: 1.5 or 2 inches wide. Custom lengths are available.
Seat Board.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Eliminates the sling effect from a wheelchair sling seat, provides a solid seating platform. Diagram and direction for making a wooden seat support for a wheelchair. the board should be placed between, not on, the rails to which the seat is fastened. Similar to commercially available product. SKILLS REQUIRED: woodworking AUTHOR: Gavee, B. TITLE: Wheelchair and Accessories REF: Book: Accent Press, Bloomington, IL; p 45. NARIC CALL NUMBER: R0848. 1981.
Seating Hardware
Seating Hardware are components for seating systems that include: 7 types of head and neck supports, 5 models of outer pommel supports, 2 inner pommel support, anterior stop bars, 10 footrest bracket options, 25 suspension hook options, slide brackets, strap hooks, tray brackets, 2 types of headrest hardware, single end button locks, removable lateral hardware, laterals, box seat hardware, solid seat and back brackets, solid seat and back hinges, kids seat bracket, and a drop away pommel.
See-Thru Work Tray (Model Nc94102)
The See-Thru Work Tray, model NC94102, is a lapboard designed to provide a work, eating, and activity surface for people who use wheelchairs. The clear tray is made of polycarbonate and bordered with an all-aluminum lip on the front and sides. The tray has a hook and loop straps that attach onto wheelchair armrests. DIMENSIONS (WxD): 23.5 x 19 inches. The width of the oval space in front of the user's stomach is 15 inches.
Self-Assisting Belt (Model 4220)
The Self-Assisting Belt, model 4220, is a wheelchair seatbelt designed to reduce siding in wheelchairs. This belt attaches to a wheelchair or geri chair using a slide buckle. Made of heavy-duty nylon, this machine-washable belt is equipped with an airline-style buckle. DIMENSIONS: Fits hips up to 60 inches.
Self-Assisting Belt (Models 4228 & 4228L)
The Self-Assisting Belt is a wheelchair seatbelt designed to reduce sliding in wheelchairs. This belt attaches to a wheelchair or geri chair using a slide buckle. Made of polypropylene webbing, this machine-washable belt is equipped with Velcro closure. DIMENSIONS: Model 4228 fits hips up to 42 inches and model 4228L is extrsa-long to fit hips up to 62 inches.
Semi-Pneumatic Eight-Inch Disc Wheels (Model 44)
Semi-Pneumatic Eight-inch Disc Wheels, model 44, are semipneumatic caster tire and wheels designed for use with wheelchairs. DIMENSIONS: 8 inches.
Semipneumatic Caster Wheel (Model 90-51605)
The Semipneumatic Caster Wheel, model 90-51605, is a semipneumatic caster tire and wheel for wheelchairs. The assembly includes bearings and a gray non marking rubber tire. DIMENSIONS (DxW): 8 x 1.75 inches. COLOR: Black or gray.
Shasta Wheelchair Tire, The
The Shasta Wheelchair Tire is a replacement rubber wheelchair tire designed for use by wheelchair users. This lightweight tire is designed to be used on low-profile rims. The tire has a smooth, non-marking tread pattern. DIMENSIONS: 24 x 1 inches.
Shear-Controlling Power Recline Systems
Shear-Controlling Power Recline Systems are powered reclining systems designed for use with power-base style powered wheelchairs. This system fits Invacare, Quickie, Jazzy, Everest & Jennings power bases and offers a full 90 degrees of tilt. This system slides the seat backward as the seat back reclines, taking pressure off sensitive areas and controlling shearing in the lumbar, sacral, and ischial regions. Standard features include a solid contoured back with high-density foam and a Cordura
Sheepette Wheelchair Armrest And Seat Pads (Models D3004 & D3005)
The Sheepette Wheelchair Armrest Pad, model D3004, and Seat Pads, model D3005, are decubitus pads designed for use by individuals at risk for pressure sores or ulcers. Made of synthetic sheepskin, the seat pad is a one-piece pad that covers wheelchair back and seat to provide pressure relief. Also made of synthetic sheepskin, the armrest pads cover the armrests of the wheelchair to reduce pressure on the arms and elbows.
Sheepskin Seat Belt Cover
The Sheepskin Seat Belt Cover is a wheelchair seat belt accessory designed for use by individuals with spinal cord injury or mobility disabilities. This sleeve fits over the seat belt and secures with Velcro to help reduce pressure and absorb moisture. They DIMENSIONS: 8 inches long. COLOR: Available bone or charcoal grey.
Sheepskin Wheelchair Arm Pad
The Sheepskin Wheelchair Arm Pad is a wheelchair armrest pad designed for use by individuals at risk for pressure sores/ulcers. Made from Medical Sheepskin, these pads attach to the wheelchair armrest with Velcro straps and are fully washable.
Sheepskin Wheelchair Arm Rest Covers (Models 112 & 113)
The Sheepskin Wheelchair Arm Rest Covers are wheelchair armrest pads designed for use by people with mobility disabilities, spinal cord injury and others who use wheelchairs. These pads are made of tanned natural sheepskin are machine washable and dryable. Each pad has adjustable Velcro straps to attach it to an armrest of a wheelchair. The pads fit full (model 112) or desk (model 113) size armrests and are sold in pairs. DIMENSIONS (LxW): 14.5 x 16 inches (model 112) or 9.5 x 5 inches (model 11
Sheepskin Wheelchair Footplate Cover
The Sheepskin Wheelchair Footplate Cover is a footplate pad designed for use by individuals who use wheelchairs. These footplate covers are made from Medical Sheepskin, are fully washable, and are held in place with elastic straps.
Sherwood Wheelchair Tire, The
The Sherwood Wheelchair Tire is a replacement rubber wheelchair tire designed for use by wheelchair users. This high-performance tire is dirt resistant and will not mark floors. It is designed to perform well for extended distances. DIMENSIONS: 24 x 1 inches.
Shoe Holders
Molded ABS plastic shoe holder with padded ankle strap and forefoot strap. Attach to footplate with screws. Also available in extra heavy duty model. Sizes: Small 4 1/2 inches long by 3 inches wide, Medium 6 inches long by 4 inches wide, Large 8 inches long by 4 1/2 inches wide, and X-Large 9 1/2 inches long by 5 inches wide.
Shoe Holders
Molded plastic shoe holder in 4 sizes, 2 1/2 to 5 3/4 inches wide by 5 1/2 to 11 inches long. 1-inch nylon adjustable velcro straps at instep and toe. Hardware for bolting to footplate included. Replacement straps, pads for straps, and brackets for Motion Designs chairs available.
Shoe Holders (Models 30101S, 30101M, 30101L, 30102S, 30102M, & 30102L)
Shoe Holders are foot positioners designed for use by individuals who use wheelchairs. Made of Haircell plastic with nylon straps with quick-release plastic buttons, these shoe-shaped positioners ensure proper positioning of the feet. The 30101 models have one-inch on center mounting holes. The 30102 models do not have mounting holes. SIZES: Both the 30101 and 30102 models are available in small, medium, and large. DIMENSIONS (WxL): The small holders are 4.3 x 6 inches. The medium holders are 4.
Shuval’s Tray
The Shuval’s Tray is a 3D printed add-on wheelchair tray designed for manual wheelchairs users to carry their lunch tray.
Side / Armrest Bags
DO IT YOURSELF PURPOSE: To provide powered wheelchair users with carrying capability. Two pocket organizers designed for use on car visors were purchased from the automotive section of a local store. One organizer was strapped to each arm and the front strap of each was clamped under the armrest pad. TITLE: Side/Arm Rest Bags. REF: http://www.wheelchairmodifications.org. The organization can also be reached at Wheelchair Modifications, 5533 A Pony Farm Drive, Richmond, VA 23227.
Side By Side
---- PROTOTYPE --------- PURPOSE: Side by Side is an accessory for the wheelchair which allows a friend, relative or caregiver to push the chair while walking beside rather than behind it. Called Side by Side, the prototype device is designed to enable eye contact to encourage conversation. This design keeps the wheelchair from turning on the spot when pushed. The device can also be folded to fit into the rear pocket of the chair.
Side Entry Backpack For Scooters (Model 70340)
The Side Entry Backpack for Scooters, model 70340, is a wheelchair back pouch designed to allow scooter users facilitated access to items in the caddy by means of a side opening rather than a top opening. The pouch includes a main compartment, kangaroo pouch, pen and pencil pouch, and front flap pouch. It attaches with adjustable straps or may be bolted to the seat back. The bag is made of 1000 Denier coated nylon Cordura. DIMENSIONS (HxWxD): 20 x 15 x 6 inches. COLOR: Royal blue, magenta, teal,
Side Entry Backpack For Wheelchairs (Model 70060)
The Side Entry Backpack, model 70060, is a wheelchair backpouch designed to eliminate the contortions necessary to open a standard zipper-style backpack or flap pouch from the chair. This backpack is accessed by opening the hex frame from the side. The caddy includes a main compartment, kangaroo pouch, pen and pencil pouch, and a front flap pouch. The bag is made of 1000 Denier coated nylon Cordura and attaches with 3/4-inch webbing with adjustable glides. OPTIONS: Backpack strap retainers avail
Side Kick Bag
The Side Kick Bag is an under seat pocket or wheelchair side pouch designed to provide carrying capacity for people who use wheelchairs. Made of nylon packcloth, this slimline pouch attaches on the inside of the armrest or under the seat and features a main zippered compartment with a ring pull and two smaller fromt pockets, one fleece-lined. DIMENSIONS (WxH): 12.25 x 7 inches. COLOR: Red.
Sidekick Wheelchair Bag (Model 162)
The Side Kick Wheelchair Bag, model 162, is a wheelchair side pouch designed for use by individuals with mobility disabilities or spinal cord injury. This denim wheelchair pouch hangs from the armrest. It has a covering flap that closes with Velcro, and hook-and-loop tab straps to hold the bag at armrest height. DIMENSIONS (HxW): 8 x 11 inches with 10-inch straps. OPTIONS: Monogram. COLORS: The bag comes in black, khaki, olive, teal, or blue denim. Monogram thread is offered in a choice of custo
Sidelyer Strap, H-Straps, & Pelvic Strap
The Sidelyer Strap, H-Strap, and Pelvic Strap are restraint and positioning belts designed for use in conjunction with the large foam positioning shapes by the manufacturer (see separate entries). The straps are fabricated of Evazote foam for cushioning ithout bottoming out. The Sidelyer Strap is designed to support the body in proper alignment when positioned on its side. It comes in Adult and Child models, both available with a hole for a gastrostomy tube. The H-Straps form a harness and are u
Sideminder Wheelchair Back (Models Mdtsm16, Mdtsm18, & Mdtsm20)
The SideMinder Wheelchair Back is a wheelchair back support designed for use by wheelchair users with cerebral palsy, neurological disabilities, or upper extremity disabilities. This steel replacement back features up-and-down and side-to-side adjustments that provide lateral support to prevent leaning to one side. This back adapts to fit non-standard size chairs. OPTIONS: Available with or without lateral supports and headrest. SIZES: Avialable for 16-inch seat (model MDTSM16), 18-inch seat (mo
Silva Wheelchair Tire, The
The Silva Wheelchair Tire is a replacement polyurethane tire designed for use by wheelchair users. This high-performance tire is made from high-quality urethane. DIMENSIONS: 25 x 1 inches.
Single Switch Remote Controlled Camera
---- PROTOTYPE --------- PURPOSE: To create a prototype of a single switch remotely controlled camera for an individual with cerebral palsy. A young man with cerebral palsy who had no use of his hands wished to independently operate a camera. Mounting the camera to the young man’s wheelchair was straightforward. The remote control cable for his camera required two switch actions, one to focus the camera and the other to simultaneously trigger the shutter. The young man currently used a switch ar
Sitkit
The SitKit is a wheelchair fitting system designed for use by clinicians and suppliers to optimize the fit of a wheelchair for an individual user with mobility or lower extremity disabilities or spinal cord injury and others who use wheelchairs. The SitKit includes a reversible caliper handle for hip width and upper leg measurements; a laser height gauge for lower leg measurement; a digital angle gauge for calculating the proper wheel camber, backrest angle, front frame angle, and foot plate ang
Skil-Care Removable Wheelchair Lap Trays (Series 7050)
Skil-Care Removable Wheelchair Lap Trays, series 7050, are designed to provide a work and feeding surface and positioning support for people who use wheelchairs. Available styles include a long-lasting Dura-Tray, a clear tray, an Econo-Tray, and a padded SofTop Tray. The SofTop Tray is available in an adult or a child's model. All trays feature straps that secure around the chair with easy-open closures. OPTIONS: Replacement straps. DIMENSIONS: The child's SofTop Tray is 19 x 22 inches.
Skil-Care Resident-Release Nylon Belts (Series 7010)
Skil-Care Resident-Release Nylon Belts, series 7010, are wheelchair seatbelts designed to provide security and positioning assistance for people who use wheelchairs. These belts secure to the wheelchair using the existing screws and are available with a choice of four closures: Side-release buckles, user-friendly buckles, Velcro, and Velcro with a red hand loop. DIMENSIONS: All models are two inches wide. The model with the side-release buckle is available in 42 or 54 inches long. The model with
Skil-Care Resident-Release Soft Belts (Series 3012)
Skil-Care Resident-Release Soft Belts series 3012,are wheelchair seatbelts designed to provide security and positioning assistance. These launderable foam padded belts are available with a choice of four closures: Side-release buckles, user-friendly buckles, Velcro, and Velcro with a red hand loop. Foam padded belt easily attaches to wheelchair kick spurs.DIMENSIONS (padded front) (LxW): 24 x 4 inches. Overall length is 81 inches.
Skil-Care Sensory Stimulation Wheelchair Tray
The Sensory Stimulation Wheelchair Tray is a wheelchair tray to give its user visual and tactile stimulation by providing a soft gel surface for the patient's arms and elbows that is colored with a night sky design. This tray allows its user to remain seated comfortably and has a wipe clean durable vinyl cover.
Skyway Wheels
Replacement wheelchair wheels and casters. Nylon mag style wheel. 6, 8, 12.5, 14, 16, 20, and 24 inch diameters. For use with pneumatic or semi- pneumatic tires. Aluminum pushrims 20 inches through 24 inches with rivnuts or tabs.
Sleeve Guards
The Sleeve Guards are sleeve protectors designed for use by individuals who use manual wheelchairs. These guards are worn over the user’s original garment to protect shirt sleeves, jackets and skin against moisture and dirt from the wheelchair's wheels. SIZE: One size fits all.
Slice Jr. Large Mini Pack
The Slice Jr. Large Mini Pack is a wheelchair side pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made from 1200D/PVC material, the unit has a large zippered storage compartment, with two Velcro straps on the back for attaching to a wheelchair. Inside is an expandable net pocket. On the front is a zippered pocket for holding smaller items safely and close at hand. DIMENSIONS (HxWxD): Main compartment is 7.5 x 6.5 x 3 inches, with with a 5-inch wide zipper
Slice Wheelchair Backpack
The Slice Wheelchair Backpack is a wheelchair back pouch designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. Made from water resistant 1200D/PVC, this unit attaches to a wheelchair with or without a push handle using two adjustable sewn-on straps with metal hardware (metal buckles and 4-metal D-rings). The unit has a large zippered storage compartment, with zippers that open from either side. Inside is a large expan
Sliding Headrest Bracket
The Sliding Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury or cerebral palsy. It is added to a headrest on a seat or wheelchair to enable headrest adjustments. This slotted interface bracket allows the headrest to be offset to either side, with infinite lateral adjustment up to 2 inches for an Otto Bock or NE-AT Headrest Bracket (see separate entry). This bracket attaches to the seating system using the existing h
Slim Armstrong Mounting System
The Slim Armstrong Mounting System is a mounting system for communication devices or switches that can be attached to wheelchairs, bed frames, tables or trays for activities at home, school, work and in the community. The device has a slender, telescoping arm that holds up to 5 pounds. The system includes the following components: a clamp for anchoring on most curved or flat surfaces, a ball joint, a flexor rod with built-in ball joint, a telescoping arm, and a small triangular mounting plate. T
Slim Jim
Wheelchair side pouch has zip closure on top, or flap with Velcro closure. Four outer pockets and securing strap at either end. 7 by 12 inches. Black or saddle vinyl.
Slim-Grip Bike Mount With Safety Strap (Model Sm532)
The Slim-Grip Bike Mount with Safety Strap, model SM532, is a cell phone wheelchair mount designed for use by individuals with lower extremity or mobilitiy disabilities or spinal cord injury. Originally designed for bicycles, this low profile mount is compatible with most smartphones with a screen size of 3.2 inches or more, with or without a case, including the iPhone, HTC, Samsung, Motorola, LG, Sony Ericsson, and ASUS. The mount has a 180 degrees tilt-swivel head that allows maximum viewing p
Slipcasting Board
The Slipcasting Board is a lapboard designed to assist users with limited strength to handle the large, heavy plaster molds that are used for slipcasting. The device consists of a 3/4-inch plywood board with an opening on one side. The user places the board between two chairs and sits on one side. The board surface supports the plaster mold and provides a safer working position to handle the heavy mold. The opening allows the slip to be poured out of the mold and into a bucket which is placed on
Smart 10J Range
The 10J Wheelchair is an electric folding and unfolding wheelchair for use by people with lower extremity disabilities to give them greater mobility, versatility, and independence. This product comes with a cushion, joystick, and 1Xbattery. It folds and unfolds in 3 seconds with minimum effort. It fits in the trunk of any car, including a Smart car.
Smartleg.
Elevating legrest that extends 3 to 5 inches when elevated. Fits any adult wheelchair from Invacare. Can be lengthened from 16 to 20 inches. Weight, 12 pounds per pair.
So Soft Deep U Headrest (Model Ssdu100)
The So Soft Deep U Headrest, model SSDU100, is a wheelchair headrest and head support designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs and need to keep their heads positioned upright and centered. This unit has aggressive laterals for maintaining head position, tapered for minimal interference of vision. The headrest has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure reli
So Soft Oval Headrest (Models Sso100S & Sso200L)
The So Soft Oval Headrest, models SSO100S and SSO200L, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. The headrest has a contoured shape for lateral support. It has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure relief and comfort. The headrest comes with a zippered Triptex cover. SIZES: Small (SSO100S) or large (SSO200L). DIMENSIONS: 11 x 5 in
So Soft Quad Headrest (Model Ssq4100)
The So Soft Quad Headrest, model SSQ4100, is a wheelchair headrest and head support designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. The unit is slightly contoured for comfort and positioning. It has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure relief and
comfort. This headrest comes with a zippered Triptex cover. DIMENSIONS: 9 x 6.5 inches.
Soft Roll Alloy Caster
The Soft Roll Alloy Caster is a caster wheel designed for use by individuals with lower extrremity or mobility disabilities or spinal cord injury. This machined alloy caster has a smooth finish to promote easier turning and less rolling resistance, while reducing some wheel chatter. The smooth finish also means dirt will not get lodged in the tread and spread around inside. DIMENSIONS: Available with a diameter of 4, 5, or 6 inches. 1.5 inches wide.
Soft Seat (Models 6392 & 6394)
The Soft Seat is a seat cover for a wheelchair designed to enhance comfort and reduce pressure sores. Model 6392 is a seat and back pad set and model 6394 is a pair of armrest pads. These machine-washable sets (sold separately) are made of synthetic fur padding and fit most wheelchairs with full-length arms. The seat back pad secures to the wheelchair with loops that slip over the push handles.
Soft Surface Transfer Board (Models Tb-23Sst & Tb-28Sst)
The Soft Surface Transfer Board is a transfer board designed for use by individuals who use wheelchairs. This board is designed to assist with transfers from a wheelchair to a softer surface such as a bed or lift chair. The pear shape of this board minimizes sinking into a soft surface when transferring, creating a more level transfer. The wide end of the board distributes the users weight over a broader area relulting in a transfer with little or no incline or decline. OPTIONS: Available with o
Solid Back
Custom size solid back with 1 inch medium density foam on 1/2 inch birch plywood. Upholstered with cover foam and vinyl cover. T-nuts for hardware attachment and headrest mounting. Custom foams available. Modifications available include curved solid back and I-back cutout. May be ordered without aluminum hardware, or mounted to chair with velcro loops, cinch straps, stationary knob-release hardware, adjustable knob-release hardware, non-adjustable drop hooks, or adjustable drop hooks. Hardware m
Solid Back Insert (Model 75)
The Solid Back Insert, model 75, is designed for use in wheelchairs with sling upholstery and push handles. The insert features a rigid base with a foam liner, a fabric cover, and loops to secure it to the wheelchair push handles
Solid Backs (Models 102-1000, 102-2000, 102-3000, 102-4000, 102-5000, & 102-6000)
Adaptive solid seat backs with 1/2 inch plywood bases, 1/2 inch foam padding and Naugahyde, shelterite or synthetic lambswool covers. Available in any size, with or without mounting hardware. Modifications available include cutouts, extra or special foam, curved back, I-back, wedge cut.
Solid Drop Seat Systems (Models 31642 & 31643)
Solid Drop Seat Systems are solid seat inserts designed for use by individuals who use wheelchairs. The systems include a seven-ply birch solid seat insert and jeavy-duty J-brackets that may be adjusted to raise or lower the seat to achieve proper positioning for the user. The seat features cut out slots to fit around frame crossmembers. DIMENSIONS: The seat insert is 3/8-inch thick. Model 31642 fits chairs with a 16-inch seat and is 13 x 16 inches. Model 3143 fits chairs with 18-inch seats and
Solid Footboard (Model 108-8016)
Solid footrest with fixed or swing away brackets. Waterproof finished birchwood with plastic edges. All sizes. Mounts with 1 inch drop hooks and 30 degree clamps.
Solid Seat
Custom size solid seat with 1 inch medium density foam on 1/2 inch birch plywood. Upholstered with cover foam and vinyl cover. T-nuts for hardware attachment and abductor mounting. Custom foams available. Modifications available include anti-thrust seat, leg length discrepancy, and built-in abductor. May be ordered without aluminum hardware, or mounted to chair with cinch straps, stationary knob- release hardware, adjustable angle knob-release hardware, non- adjustable drop hooks, or adjustable
Solid Seat (Model Ss1000)
The Solid Seat, model SS1000, is a drop seat for a wheelchair designed for use by individuals with a need for a lower seat due either to a high cushion or who propel the wheelchair with their feet. The Drop Seat is made of durable HDPP and fits most manual and powered wheelchairs. The hole pattern accomodates one-inch mounting increments. Velcro strips are provided to secure a cushion. The hardware adjusts from one-inch above a tube frame to 3 inches below a tube frame. DIMENSIONS (LxW): Avai
Solid Seat And Back
Solid seat and back inserts. Hardwood plywood base with firm foam padding. Naugahyde cover. Various hardware styles and clamps attach units to wheelchair. Customized to fit any wheelchair frame; manual, power drive, travel chair or sport chair. Back insert models: T-back, R- back or with straps.
Solid Seat Insert (Model 94)
The Solid Seat Insert, model 94, is designed for use in wheelchairs with sling upholstery to provide additional seating support. The insert has a rigid base with a foam liner.
Solid Seat Inserts (Models 31640, 31641, 31645, 31646, 31647, & 31648)
Solid Seat Inserts are designed for use by individuals who use wheelchairs. Available in a choice of seven-ply birch wood or paper phenolic with or without a hand hole, these inserts can be used in a standard sling seat to provide support for a cushion or as a base for a custom seating system. DIMENSIONS:Models 31640, 31645, and 31647 are 16 x 16 inches. Models 31641, 31646, and 31648 are 16 x 18 inches. The birch models are 3/8-inch thick. COLOR: Models 31647 and 31648 are black. The other mode
Solid Seat With Adjustable Brackets And Split Collar Clamps (Model 101-4000)
Solid seat, 1/2 inch marine grade plywood with 1 1/2 inches of foam padding, naugahyde upholstery. Brackets allow up to 3 inches of drop or 3 inches of raise in seat, or tilt in seat to accomodate needed angle of hip flexion. Can be fixed or removable depending on placement of the clamps. Seats are cut to fit between the rails.
Solid Seat With Attaching Hardware (Model Ee1) & Solid Back (Model Ee2)
Solid seat and back, 1/2 inch marine grade plywood and 1 1/2 inches of foam padding. Hardware is designed to allow adjustment of seat to back angle, seating depth and flexion. Naugahyde upholstery. Full of cushion is rounded. Custom widths.
Solid Seats (Models 101-1000, 101-2000, & 101-3000)
Adaptive solid seat, 1/2 inch plywood base, 1 to 1 1/2 inch foam padding. Naugahyde, shelterite or synthetic lambswool covers. Any width or depth available. Special modifications available include cutouts, leg length discrepancy, wedge cut, special foam, anti-thrust cushion. Available with or without mounting hardware.
Solo Axis
The Solo Axis is a legrest designed for use by individuals with lower extremity, mobility, or neurological disabilities or spinal cord injury. This legrest has a spring-loaded, single post foot plate with power elevation and articulation at the knee pivot point. For safety, all moving parts are under the seat.
Special Tomato Jogger Stroller
The Special Tomato Jogger is an easy folding, lightweight, all terrain stroller pushchair for children, up to 110 pounds, with mild to moderate physical involvement or special needs. The jogger comes standard with a functional rear suspension to promote a smooth ride over most surfaces. The swivel front tire makes it possible to maneuver through indoor spaces. For straight line strolling and rougher terrain, the front wheel can be locked inline.
Spenco Foot Pillow (Model 31-559)
The Spenco Foot Pillow, model 31-559, is a pair of foot warmers and protectors designed for persons with lower extremity disabilities. The slippers are constructed of thick cotton/polyester and help relieve pressure on the foot, heels and ankle, whether a person is lying in bed or sitting in a wheelchair. SIZE: One size fits all.
Spenco Wheelchair Pad (Model 31-252)
The Spenco Wheelchair Pad, model 31-252, is a decubitus pad and armrest pad for persons using wheelchairs. The cotton/polyester covering provides protection for the arms and torso. The back of the pad is covered with waterproof sheeting.
Spoke Guards
Spoke Guards are decorative spoke protectors designed for use by individuals who use wheelchairs. These guards cover the spokes on rear wheelchair wheels and are offered in a variety of designs in eight categories: Animals, children's designs, groovin' designs, flower power, black-and-white, space, sports, and miscellaneous. Designs include dolphins, tigers, crayons, elf and snail, roses, flower and butterfly, geometric designs, black-and-white checkerboard, black-and-white yin and yang, space s
Sport Light Extreme Slx With R10 Hub
The Sport Light Extreme SLX with R10 Hub is a manual wheelchair wheel designed for use on sport wheelchairs. The double-walled, CNC machined, aluminum hub uses a 0.625-inch axle to reduce the risk of bending the axle during sports play. The wheel has either 18 or 24 spokes made of PBO fiber. DIMENSIONS: Diameterl is 24, 25, or 26 inches. Spokes are 4 millimeters diameter. COLOR: Spokes are black, white, red, yellow, blue, pink, green, or orange.
Sports Pac, Neon Sportspac, & Junior Sportspac
The Sports Pac WH160SP, Neon SportsPac WH160N, and Junior SportsPac WH160J are wheelchair back pouches designed for sports wheelchairs. The bags have an adjustable strap system that fits over the back of the chair. They have a main compartment, outer pocket, lid pocket and two outside mesh pockets with Velcro closures. The Neon SportsPac is the same as the original SportsPac, but constructed of mixed neon colors in packcloth and cordura. The Junior SportsPac is sized for smaller chairs. Optional
Standard Comfortline Armrest Series
The Standard Comfortline Armrest Series are add-on armrests and lapboards designed to provide a small writing or work surface for people who use wheelchairs. These wooden armrests have foam padding covered in molded satin vinyl and are available in fixed or flip- away models for both right and left wheelchair arms. These armrests feature a molded cup holder recess. DIMENSIONS (WxD): 9.5 inches wide at the widest point, tapering to 8 inches x 22 inches. The armrests have a .5-inch thick wood base
Standard Curved Padded Headrest (Model Hrc100)
The Standard Curved Padded Headrest, model HRC100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. It has a contoured U shape for positioning, and foam padding with a zippered Triptex cover. DIMENSIONS: 11 x 4 inches. Padding is 2.5 inches deep.
Standard Saddle Armrest Bag
The Standard Saddle Armrest Bag is designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. The device attaches to the users armrest bag by wrapping the fabric with the 2 inches hook strap over the top of your armrest and securing it to the 2 inch loop strap. Use the 5/8 inch hook and loop strap (located at the bottom of the bag) to secure it to the seat post or horizontal frame of the chair. Fits armrest from 1-inch round tubing to deluxe scooter armr
Standard Seatback Backpack
The Standard Seatback Backpack is a single compartment bag designed for use by wheelchair users with mobility or lower extremity disabilities or spinal cord injury. It includes straps that go over the seatback of the wheechair or scooter.
Standard Viewline Plus Armrest Series
The Standard Viewline Plus Series are add-on armrests and lapboards designed to provide a small writing or work surface for people who use wheelchairs. The armrests are fabricated of transparent, unbreakable, scratch-resistant polycarbonate and are available in fixed or flip-away styles for both right and left wheelchair arms, and are available in armrest only or armrest with PVC plastic rim models. DIMENSIONS: 3/8 x 22 x 9.5 inches wide at the widest point, tapering to 8 inches. COLOR: The plas
Standard Woodline Light Reversible Armrest
The Standard Woodline Light Reversible Armrest is an add-on armrest and lapboard designed to provide a small writing or work surface for people who use wheelchairs. The 7-ply Finnish birch plywood armrest comes standard with a clear lacquer finish and is designed to be assembled by the user in either a right or left configuration. Model 31326 is a fixed armrest and Model 31328 is a flip-away style; all necessary mounting hardware is included with both models. DIMENSIONS: 3/8 inch thick x 22 inch
Stash And Flash Wheelchair Backpack
The Stash and Flash Wheelchair Backpack is a wheelchair back pouch designed for wheelchair users. The bag fits wheelchairs 14 to 18 inches wide without rubbing wheels and can be used with wheelchairs with or without handles. Features include netted pockets for holding water bottles and mobile phones within easy reach without having to open the bag. Other features include a reflective strip to improve visibility at night making it visible for drivers, zipped pockets for keys and other personal it
staxi Medical Chair
Stay Put Commode, The Non-Transfer Commode
The Stay Put Commode is a wheelchair attachable commode that is specifically designed for wheelchair users who cannot independently transfer out of their wheelchair to a toilet or standard commode. The Stay Put Commode replaces the standard wheelchair seat, but it allows the user to maintain the comfort and mobility of their standard chair.
Stay Puts
Stay Put is designed for use by individuals with limited upper and lower extremity mobility associated with cerebral palsy, traumatic brain injury or stroke. It is designed to hold just about any object – toys, utensils, writing implements, etc. – and keep them from dropping on the floor. Objects are easily retrievable and stay clean. Two strong suction cups hold the Stay Put in place on your wheelchair tray, table, desk, or bed tray. Three chains each equipped with a key ring allow you to easi
Stealth Elite Headrest (Model Sm-Se210)
The Stealth Elite Headrest, model SM-SE210, is a headrest designed for use by individuals who use wheelchairs. This headrest is intended for individuals who do not need a midline cue. The two lateral swing-away components can be used for switch mounting and if a sensor is added in the backpad, it can also be equipped for computer access.
Stealth Ultra Headrest (Model Sm-Su200)
The Stealth Ultra Headrest, model SM-SU200, is a combination wheelchair headrest and switch mounting hardware designed for use by individuals with severe physical or neurological disabilities or spinal cord injury. The sub occipital component aids the user in finding the midline. The two lateral swing-away components can be used for sensor mounting and a sensor can also be mounted in the backpad.
Steel Channel Bracket Attaching System (Model 30300)
The Steel Channel Bracket Attaching System, model 30300, is lapboard mounting hardware designed to secure armrest-style trays to wheelchairs. This heavy-duty steel bracket includes all required mounting hardware for attaching to a tray (not included) and enables a tray to slide on to the armrests from the front. This flip-away bracket fits standard wheelchair armpads and permits chair entry and exit without removing the tray. DIMENSIONS: Fits 1 1/8-inch high standard pads. WARRANTY: This product
Sun
TheSun is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This custom wheel has mirror bright, machine polished surfaces, and is made from computer machined 6061-T-6 billet aluminum with double walled rims and sealed bearings. Hand rims are available with an anodized or vinyl-coated surface or with quad projection. DIMENSIONS: 24 or 25 inch diameter. CAPACITY: 250 pounds. WEIGHT: 3.9 to 4.4 pounds. COLOR: Natural alu
Super Clamp
The Super Clamp is a mounting clamp for accessories designed to attach to wheelchair arms or any other kind of frame. The jaws of the clamp open up to a maximum of two inches wide. The clamp has a receptacle to screw into photographic or other equipment. The device is made of cast alloy with a high strength to weight ratio. The jaws are friction lined and screw operated. The clamp has a special detent operated safety lock that holds accessories in place even if the locking mechanism is not tight
Supertote Carryall
The SuperTote Carryall is a wheelchair side pouch or a carrying bag for a walker or crutch designed to provide carrying capability for people with mobility disabilities. Made of durable machine-washable nylon, this tote features pockets with zipper closure. DIMENSIONS: 9.5 x 7 x 4.5 inches. COLOR: Blue or black.
Support Fixture For Powered Wheelchair
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a support fixture for a powered wheelchair for a woman with a progressive neurological disorder to travel independently away from the hospital with all her required medical pumps and support devices. This young woman is dependent on getting her food and medications through pumps attached to her powered wheelchair by a customized bracket. As her medical needs have increased she needed three additional pumps to meet her needs, but the bulk an
Swing Away Stump Support
The Swing Away Stump Support is an amputee leg support designed for use with wheelchairs. The device has a metal frame and a vinyl covered cushioned leg support for below knee amputees. Available for the right or left leg, the support adjusts horizontally and vertically. Models are available to fit a variety of chairs, including Everest & Jennings, Invacare, and Breezy.
Swing Away Tray (Model Sat126)
Durable 3/8 inch clear polycarbonate tray supports a weak or paralyzed arm. Acts as a portable writing or eating surface and/or reading support. Tray curves around body front during use, but quickly swings up and over wheelchair wheel for safe storage when not in use. Lightweight and has 5/8 inch protective white rubber trim that is removable for easy cleaning. Easy to install. Available for right or left side.
Swingaway Joystick Bracket
The Swing-Away Joystick Bracket is a joystick holder designed for midline and other special positioning needs. The bracket swings out of the way when transferring or pulling up to a table or desk. Five styles are available. The pull-pin release styles use the Miller's Swing Away Mounting Block (see separate entry). The push button styles operate with just a light to medium touch when strength or hand function is limited.
Swingaway Mounting Kit (Model 3150-1)
Mounting system for the 3185 joystick for chin oepration. Includes a 12 by 18 inch right angle mounting rod, custom sizes or bends can be provided. A 1/2 inch stainless steel mounting rod fits into a 3/4 inch vertical shaft and a swingaway strap clamp for attachemnt to a standard 7/8 inch diameter wheelchair/power recliner back bar. Permits the joystick to be moved away from the user by an attendant and returned to its original position without the need to readjust the mounting apparatus.
Swingaway Mounting Kit (Model 3205-2)
Unsed for mid-line mounting of a hand oeprated joystick. this mounting kit may also be used for mid-line mounting of other devices if the device accepts a 1/4-20 threaded bolt for attachment. Consists of a 1/2 inch diameter stainless steel mounting rod fitted to a 3/4 inch vertical shaft and a swingaway strap clamp for attachment to a standard 7/8 inch diamter armrest frame. A rod clamp is also included for mounting those joysticks which are not furnished with a rod clamp. permits the joystick t
Swingaway Mounting Kit (Model 3514)
Used for mounting a head operated actuator to the wheelchair back bar or push handle. The mounting kit consists of two right angle mounting rods joined by a double rod clamp and fitted to a pivot shaft, and a strap clamp for attachment to 7/8 inch diameter wheelchair tubing. Permits the actuator to be moved away from the user by an attendant and returned to its original position without the need to readjust the mounting.
Swinging Backpack
---- PROTOTYPE --------- PURPOSE: A group of seven students from a Wethersfield, CT high school developed the Easy Access Transport System (EATS). The device is designed to solve a problem that a student with Charcot-Marie-Tooth (CMT) disease had accessing his books in his backpack on the back of his wheelchair. Over two months, the EATS was designed to allow the student with CMT to swing his backpack on hinges and bring it around to his lap so he could access his books. The students started wit
Swish
The Swish is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Made from computer machined 6061-T-6 polished billet aluminum, it has mirror bright surfaces, double walled rims, and sealed bearings. Anodizing is available. Hand rims are available with quad projections or with an anodized or vinyl-covered surface. DIMENSIONS: 24- or 25-inch diameter. Hub width (bearing to bearing) 2.06 inches. CAPACITY: 250 pounds. WEIGHT
Switch Head Control (Model 3519)
A head operated switch actuator incorporating three Model 3265 Disc Switches. The Disc Switches are attached to adjustable monting hardware for positioning the switches consistent with the user's abilities. Normally used in conjunction with the Model 3450 Triswitch Input Controller, and mounted with the Model 3514 Swingaway Mounting Kit.
Switch It Remote Commander
The Switch It Remote Commander is an attendant controller designed for use by caregivers of wheelchair users. This remote device allows someone not sitting in the wheelchair to control the drive functions of the chair.
Switch It Remote Stop Switch
The Switch It Remote Stop Switch is a powered wheelchair controller designed for use by wheelchair users and their caregivers. The remote stop switch enables the user to stop the chair by pressing a button. This radio frequency based unit is designed to work within a single room for a distance of up to 30 feet.
OPTIONS: Key chain remotes are available.
Switch Mounting Kit (Models Smt & Smw-1)
The Switch Mounting Kit for Tables, model SMT, and Switch Mounting Kit for Wheelchairs SMW-1, are control switch accessories for mounting switches in a variety of locations. Model SMT is designed for use on tables or table-like surface, and model SMW-1 is designed for use with wheelchairs. The Switch Mounting Kit for Tables includes a gooseneck, tilt-top switch mounts, and an adapter bracket to fasten it to tables or shelves. The Switch Mounting Kit for Wheelchairs has a tubular bracket for clam
Switch Options/ecu Module For Arrow Mcc (Model 1551M)
Optional module installed into Arrow MCC wheelchair controller. Provides for switch, sip'n'puff, rim head control of wheelchair. Attendant control input. Two connectors, each with 4 ECU output switch closures, to operate recliner or other devices. Module provides method of controlling accessories by only adding one switch to basic joystick; also allows other control techniques. May set 1, 3, or 5 forward speeds; selectable cruise mode allows control to be released while chair continues forward;
Switch Output Cable (Model 3329)
Used to expand the capability of a Multimode Interface by providing four isloated and independent switch closure outputs controlled by the Multimode's auxiliary operating mode. These outputs (minature phone plugs) may be used to operate various devices if the device is designed for oeration by one to four indpendent switches.
Switch Output Controller (Model 3340)
Used to expand the capbility of a Multimode Interface by providing four isolated and independent switch closure outputs controlled by the Multimode's auxillary operating mode. These outputs (miniature phone jacks) may be used to operate various devices if the device is designed for oepration by one to four independent switches. Includes additional circuitry to inhibit the Multimode's automatic reset function to allow uninterrupted operation.
Switched Head Arrays
The Switched Head Arrays are powered wheelchair controllers designed for use by individuals with severe physical disabilities or spinal cord injury. These arrays are an arrangement of electronic sensors in a head rest designed to enable control of the functions of a power wheelchair via head movement. These systems utilize an adjustable and growable three-pad headrest with one Zero-Touch Sensor (ZTS) in each pad. As standard, the right pad turns right, left turns left and center activates forwar
Swivel Tube Assembly (Parts 1501, 1501-01, 1502, 1502-01, 1503, 1503-01)
The Swivel Tube Assembly is interface hardware designed for positioning a wheelchair headrest. The Swivel Tube Assembly attaches to the recessed area of the headrest. OPTIONS: A custom made Swivel Tube Weldment is available. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLOR:Both the original and the custom made options are available in black and stainless steel.
Synthetic Lambskin Armrest Pads (Model Msc019670)
Synthetic Lambskin Armrest Pads, model MSC019670, are wheelchair armrest pads designed for use by individuals with mobility disabilities or spinal cord injury. The pads are flame-retardant, machine washable, and latex-free.
Synthetic Sheepskin Wheelchair Accessories (Models 703010, 703020, 703040, & 703050)
The Synthetic Sheepskin Wheelchair Accessories are a set of wheelchair armrest and legrest pads and seat and back cushion covers designed to provide comfort and protection for people who use wheelchairs. All items are made of high-pile synthetic sheepskin and are nonallergenic. Model 703010 is a pair of wheelchair armrest pads, model 703020 is a wheelchair legrest pad that fits between and over the legrests, model 703040 is a pair of footrest pads, and model 703050 is a set of a wheelchair seat
T Mods (Mod J)
Solid back insert modification for any Freedom Design solid backs. Backs are cut in the shape of a "T" to permit maximum adjustability of trunk supports. Only works with Econo-Ease Hardware.
T-Gel Plus Solid Seat Insert Cushion
The T-Gel Plus Solid Seat Insert (SSI) Cushion, models 1294 and 1295, is a combination cushion utilizing the Alimed Solid Seat Insert and a dry flotation T-Gel Plus Cushion (see separate entries). The cushion is intended to correct positioning of individuals in nsling seat style wheelchairs by providing a flatter sitting base. This semi-rigid base is 3.5 inches thick and creates a more stable sitting surface. DIMENSIONS:16 x 16 inches (no. 1294) or 16 x 18 inches (no. 1295).
Tablet Arms Tray (Model 11H)
The Tablet Arms Tray 11H is a swing away lapboard designed for individuals who frequently transfer in and out of a wheelchair. This portable tablet sized tray can be carried in a wheelchair backpack or stored without obstruction by snapping it onto the side of the chair. The tray is made of clear, nearly unbreakable polycarbonate plastic with a rim. Trays are made for right or left hand use. WEIGHT: Approximately 5 pounds.
Tablet Holder with Mount, Model 1568
Tablet Holder with Mount is designed for a person who needs special physical placement. The mounting system attaches to a wheelchair, tabletop, bedrail or tray. It is compatible with most tablets and e-book readers including the Kindle, Kindle Fire, Nook, Motorola Xoom, Samsung Galaxy Tablet and similar tablets.
Takeoff Sport And Wheelchair Gloves
TakeOff Sport and Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Made from Amaretta synthetic leather, these half-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue backs.
Takeoff Sport And Wheelchair Gloves-- Full Finger
TakeOff Sport and Wheelchair Gloves--Full Finger are push gloves designed for use by individuals who use wheelchairs. These full-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue backs.
Takeoff Sport And Wheelchair Gloves-- Half Finger, Full Thumb
TakeOff Sport and Wheelchair Gloves--Half Finger, Full Thumb are push gloves designed for use by individuals who use wheelchairs. These half-fingered, full thumb gloves are lined with gel througout the palm and all five digits, and the thumb and palm are reinforced with rubber material for improved grip.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra
Takeoff Sport And Wheelchair Gloves--Half Finger
TakeOff Sport and Wheelchair Gloves--Half Finger are push gloves designed for use by individuals who use wheelchairs. Made from cabretta leather, these half-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue back
Tarsalrest Adjustable Foot Support (Model Fr19Aj)
The TarsalRest Adjustable Foot Support, model FR19AJ, are foot supports ergonimcally designed to support proper posture, reduce fatigue and back strain and relieve stress on legs, back and neck. The tilting support platforms allow the user to vary leg positions and aids in circulation in legs and feet. The extra height with this support is ideal for any one who works on a stool or high chair. The adjustability makes it versatile for different environments or tasks. The non-skid platform is rubbe
Tarsalrest Foot Support (Model Fr19 & Fr19X)
The TarsalRest Foot Support, models FR19 and FR19X, are a foot supports designed to promote proper posture, reduce fatigue and back strain, and relieve stress on the legs, back and neck. They are ideal for providing circulation in the legs and feet. These foot supports feature a chrome frame that is durable and lightweight, a non-skid platform surface that won't damage shoes, and a tiliting support platform that allows users to vary their leg position. DIMENSIONS: Two models available in 3 or 6
Tash Sip 'n' Puff Adaptor (Model 32676), 1555 Adaptor (Model 32677), Joystick Adaptor (Model 32678), Mk2 Adaptor (Model 32679), & Adaptor Clamp Bushing (Model 32687)
Adaptor Clamps are switch mounting hardware designed to secure controls to wheelchairs. All models are made of steel and coated with black baked epoxy. The TASH/Sip-N-Puff Adaptor, Model 32676, is designed to hold the TASH joystick and other controls. The unit is equipped with a metal loop which allows the electrical cord to be slipped through without removing the end plug. Model 32677, the 1555 Adaptor, is a clamp designed to hold the Invacare 1555 remote joystick by utilizing existing joystick
Tech Table
Tech Table is a lap tray designed for use by individuals who use wheelchairs or scooters. The unit features a zippered Cordura nylon case with straps with buckles to secure it to the wheelchair, a handle for transfers, and a removable, wipe clean ABS plastic top that is suitable for reading, writing, dining, and recreation. The padded, foam-lined storage area under the top features five organizer pockets and accommodates books, files, pens, wallets, calculators, etc. The case includes two straps
Tecla Switch Kit
The Tecla Switch Kit is intended for wheelchair users who can access a light-touch switch. The Tecla Switch Kit is a good option for wheelchair users who do not have an environmental control unit in their wheelchair but want to access and control their smartphone or tablet. The Tecla Swtich Kid includes:
Tecla Wheelchair Kit
The Tecla Wheelchair Kit is ideal for any user in a wheelchair with an Environmental Control Unit looking to control their smartphone or tablet with Tecla. The Tecla Wheelchair Kit includes the:
Telescoping Mount Hardware For Wheelchair Tray (Model 11.1)
The Telescoping Mount Hardware for Wheelchair Tray, model 11.1, is lapboard mounting hardware designed to secure trays to wheelchairs. This system includes powder coated arms, tubes, rings and poly-lock pegs to enable a lapboard or tray to be mounted to a wheelchair. WEIGHT: 15 pounds.
Temporary Wheelchair Headrest
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Allows those without a wheelchair headrest to have a supportive rest that can be efficiently attached and removed from the chair. PVC pipes are attached to the chair and foam cover as well as vinyl create a soft cushion for the head. COMMENTS: The headrest allows those with a wheelchair to have a cushioned head support.
Terminator
The Terminator is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This billet aluminum wheelchair wheel is composed of 6061-T6511 aircraft quality aluminum plate. It is CNC precision machined. Polished aluminum handrims are included. DIMENSIONS: 24 or 25 inch diameter, 1 inch width. CAPACITY: 250 pounds. COLOR: Natural aluminum with optional gold, red, blue, purple, or black anodizing. Hand rims are available with cl
Terry After Bath Cover Up Poncho
The Terry After-Bath Cover Up Poncho is designed for use by adults and children who use wheelchairs. Large poncho style after-bath cover up. User can use instead of a towel. Snaps under arm to create roomy sleeves and has an extra large hood. Reinforced with piping all around.
The Communication Station
The Communication Station is a wheelchair mounting kit for communicators designed to clamp an augmentative device to a wheelchair for individuals who are non-verbal and use a wheelchair. It is designed to "lock in" communciation devices at the right height, position and angle. The monoclamp is the key to the Communciation Station and can be configured in various combinations with almost limitless possibilities. The family of mounts can adapt any device to the left or right side of any wheelchair
Theraslide Transfer Boards
Theraslide Transfer Boards are designed to assist people who use wheelchairs. The 20 models of these boards are constructed from defect-free birch plywood and machined from 7-ply base board with 3 additional plies form-laminated over this surface from end to end, producing a smooth, uninterrupted surface. All edges are computer routed and the surface is machine- and hand-sanded and finished with multiple coats of semi-gloss lacquer/sealer. Models include the plain board, board with telescope and
Theratray (Models 31100 & 31105)
The Theratray, Models 31100 and 31105, are lapboards designed for use by people who use wheelchairs. The trays are fabricated of polyurethane foam to eliminate sharp edges, and strengthened by a 0.25-inch Aspernite wood insert. Both models include a fully molded rim and straps. DIMENSIONS: The Adult model (no. 31100) is 23.5 x 22 inches, with a 15 x 9 inches torso cutout. The oblong juvenile size (no. 31105) is 26.5 x 24 inches, with a 10.5 x 6 inches torso cutout. WARRANTY: The manufacturer war
Thirst Free
Thirst Free is a wheelchair drink holder designed to provide hands-free carrying of beverages for individuals with mobility disabilities. The adjustable, plastic device features a wide body with a plastic ring to hold the cup. Molded clamps at the top and bottom of the device secure it to the side rails of wheechairs, bed rails, and the front horizontal bars of walkers.
Thomashilfen Quick Base (Q-Chassis) High-Low Base
Thomashilfen Quick Base (Q-Chassis) High-Low Base is an alternative frame designed for use by children with neurological and mobility disabilities. It that allows you to move the Thomashilfen seating systems from the mobility or stroller base, creating an indoor base that is great for family, therapy, or classroom inclusion. The Thomashilfen Quick Base is equipped with a patented tipping prevention function called the Balance Safety System or BSS. When the back of EASyS is reclined, the seat
Thought Controlled Wheelchair-Mounted Robotic Arm
---- PROTOTYPE --------- PURPOSE: Scientists at the University of South Florida have created a prototype of a wheelchair-mounted robotic arm controlled by thought to be used by individuals with ALS or full body paralysis. This device will allow those with severely limited mobility to perform simple daily activities for him- herself. EEG scans have allowed patients with ALS to communicate through monitored electronic brain impulses (P300 brain waves). Using these EEG-related technologies with the
Three-Dimensional Aid For Teaching Wheelchair Maintenance.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Visual aid showing the interior and exterior components of a wheelchair. Developed as a training tool in wheelchair maintenance. Describes training tool designed to allow persons with little mechanical experience to see how wheelchair components interrelate. One side represents an exterior view of an intact wheelchair, the other depicts unassembled interior components (i.e., bearings, axles and front post guides). Lists material needed and describes co
Thriftytray (Models 31128, 31129, 31255, 31256)
Thriftytrays are lapboards designed for attaching to wheelchairs. These hardboard trays have rectangular work surfaces and are available in four models: Model 31129 is an adult tray with straps; Model 31128 is an adult tray with foam pads and straps; Model 31255 is the extra-wide tray with straps; Model 31256 is the extra-wide tray with foam pads and straps. DIMENSIONS (WxD): The adult trays are 23.5 x 22 inches with a 15 x 9 inch torso cutout; X-wide trays are 25.5 x 22 inches with a 15 x 9 inc
Tilt In Space Systems
Tilt In Space Systems are powered tilt in space systems designed for use with power-base style powered wheelchairs. This system fits Invacare, Quickie, Jazzy, Everest & Jennings power bases and offers up to 57 degrees of tilt. Standard features include a solid contoured back with high-density foam and a Cordura-Lycra cover, full-length muti-mount back rails, a flat solid seat pan for ease in cushion installation or change, a Rock-n-Lock Akton Gel headrest with a Cordura-Lycra cover, hardware
Tilt Seat
CUSTOM ADAPTATION PURPOSE: To provide a custom tilt seat for a powered wheelchair. Accelerated Rehab in Texas creates after market seating systems for wheelchairs. A system that meets the needs of the user is created to fit any wheelchair to custom measurements. The existing tilt seat no longer provided sufficient support for the user. The new seat was taller and an adjustable headrest was added to the back. The adjustments were made using a J2 back. Flip-up armrests and new footrest hangers we
Tilt'n Turner
The Tilt 'n Turner is a communicator or computer mounting kit for wheelchair or a camera mount for wheelchair designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. The device can also be used to mount trays, easels, reading stands, remote controls and more. The device is equipped with a quick-release mounting plate offering 0 to 90 degrees of tilt and a paddle to unlock the joint to rotate the attached tray or device 360 degrees. There are 12 memor
Tilt, The
Reclining wheelchair conversion transforms a normal reclining wheelchair frame into an orientation in space wheelchair frame. Maintains a fixed hip position. Seat width adjusts 14 to 18 inches. Seat depth adjusts 19 to 23 inches. Standard front rigging includes footrests only, does not include elevating legrest pads. Includes mounting hardware, one allen key, four wheelchair telescope tube spacers, and instructions included. Available in five models: tilt with no arms, full length arms, desk arm
Tilt-A-Tray Adjustable Wheelchair Tray (Models H70670-0000 & H70670-0001)
The Tilt-A-Tray Adjustable Wheelchair Tray is a swing away lapboard designed to adjust vertically and tilt forward and back. The tray is attached to the wheelchair frame and swings away for access to the chair seat. The tray is made of clear polycarbonate and has front and rear edge bars. The right side is mounted to a hinged bar and the left side is held by suction cups mounted to adjustable bars. Fittings are molded of high-strength ABS plastic. Extension rods and braces are made of stainless
Tiretyte Ii Heavy Duty Tire Sealant
Sealant is a ethylene-glycol based solution that remains in permanent liquid form. Can be used in all tube and tubeless tires, will seal up to a 1/4" puncture. Requires an injector pump ($40) for installation. Sealant sold in 5 gallon containers ($195).
Tms Padded Chair Belt
Padded belt support. Two 12 inch long canvas pads with webbing strap sewn at one end. Straps attach under wheelchair upholstery screws and canvas pads fit across abdomen. Velcro closure.
Tms Padded Chair Belt
Belt for wheelchair, webbing straps for attachement to chair, Wide padded canvas body strap, two rows of velcro for closure.
Tms Padded Legrest Panel
Padded legrest panel. With Velcro straps to attach panel to wheelchair legrest frame. Fits standard and narrow adult chair.
Tms Solids, Solid Insert Seats And Backs
Solid seat and back inserts. Plywood base with padded foam and vinyl cover. Available in standard adult, narrow adult. Fits over regular seat and back. Back secured over push handles with fabric loops.
Tms Wheelchair Pouch
Variety of wheelchair back pouches. Soft sided with cover flap. Strap loop on pouch slip over wheelchair push handles. Some with outer pockets. Variety of fabrics. Folds with wheelchair. DIMENSIONS: 14.5 x 12 inches or 14.5 x 17 inches. Specify narrow or regular wheelchair 12 or 14 inches wide.
To Narrow Your Chair.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Describes method to temporarily narrow a wheelchair. Suggests pulling the front or rear posts of the wheelchair together with a strong leather belt or a straightened coat hanger. AUTHOR: Lunt, S TITLE: Handbook for the Disabled: Ideas and Inventions for Easier Living REF: New York: Charles Scribner's Sons: p 212 NARIC CALL NUMBER: R1616 PAGES (including cover): 2 1982.
Toe Loop (Model 82)
The Toe Loop, model 82, is a toe strap designed to prevent the user's foot from slipping forward off the wheelchair footplate. The strap is equipped with buckles for adjustment and are attached to the front of the footplate.
Tongue Drive System
---- PROTOTYPE --------- PURPOSE: To create a prototype of a powered wheelchair contol system operated by a tongue switch in dental retainer for individuals with upper and lower extremity, mobility or neurological disabilities or quadriplegia to navigate a powered wheelchair. The newest version of the Tongue Drive System uses a dental retainer with sensors to help control the system. The embedded sensors within the retainer track the movements of a small magnet attached to the tongue. The wirele
Top Drop Clamp Attaching System (Model 31070)
The Top Drop Clamp Attaching System, model 31070, is lapboard mounting hardware designed to secure trays to wheelchairs. This system enables the tray (not included) to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. Made of glass-filled nylon, the clamps adjust to fit arms of different widths and pads of d
Tough-Claw™ Mount for Xbox Adaptive Controller
The Tough-Claw™ Mount for is a mountable component for the Wheelchair Seat Mount for Xbox Adaptive Controller. It can be used to offer more flexibility to users making use of the Adaptive controller.
Transfer Board (Model 765)
The Transfer Board, model 765, is designed to aid a person with lower extremity or mobility disabilities or spinal cord injury to transfer from a wheelchair or chair to a commode or bed and back. It has gradually tapered ends and is constructed of hardwood and has a smooth, natural finish. DIMENSIONS (WxLxT): 8 x 30 x 0.75 inches.
Transfer Board (Model 765H)
The Transfer Board, model 765H, is designed to aid a person with lower extremity or mobility disabilities or spinal cord injury to transfer from a wheelchair or chair to a commode or bed and back. It features hand slots with tapered ends, and it is constructed of 14 ply hardwood with a smooth, natural finish. DIMENSIONS (WxLxD): 8 x 30 x 0.75 inches; hand slots 19 inches apart.
Transfer Boards
Transfer board made of solid red oak electronically glued for strength and crack resistance. Finished boards are coated with urethane sealer and polished. Unfinished boards are sanded smooth and are ready to finish. Boards are 8 inches wide, available without hand hole, with one hand hole or with 2 hand holes, and in 24 or 30 inch lengths.
Transparent Trays
Transparent Trays are lapboards made of a see through polycarbonate plastic. The trays enable open visual field for safer wheelchair mobility. Several models are available: an adult model with an anodized aluminum rim (no. 8696, $67) and an adult model without a rim (no. 8242, $72.33) with Velcro straps, and a pediatric model (no. 8306, $105.45) with Velcro straps. DIMENSIONS: Adult size models are 23.5 x 22 inches; pediatric size is 20.5 x 18 inches; all models are .25 inches thick.
Tray Attachment
This Tray Attachment is a wheelchair lapboard, to be used in conjunction with the "Bowling Ball Holder Ring". This attachment converts the Bowling Ball Holder Ring into a tray which may be used for dining, letter writing, as a class desk, etc. The tray is made of a waterproof material.
Tray Bracket (Model Tr30 & Tr31) And Tray Bracket Receptacle (Tr32)
The Tray Bracket ($50, model TR30 & TR31 for left and right armrests, respectively) and the Tray Bracket Receptacle ($70, TR32) are designed to attach a tray to the armrest of a wheelchair or seating system. The units are compatible with many armrests. The bracket is mounted on one armrest and the receptacle is mounted on one side of tray. Support on both sides is recommended for heavy duty applications.
Tray Clamps (Model 31086)
Tray Clamps, Model 31086, are lapboard mounting hardware designed to mount trays and lapboards to wheelchairs. These clamps provide a means of locking trays to wheelchair frames using one lever motion. WARRANTY: The manufacturer warrants this product to be free of defects in materials and workmanship for 90 days from the date of purchase.
Tray For Powered Wheelchair
---- PROTOTYPE --------- PURPOSE: To create a prototype of a tray for a powered wheelchair for individuals with a C6 spinal cord injury (SCI) for use with power wheelchairs. The requirements for the tray are defined to meet the American with Disabilities Act (ADA) and through interviews with power wheelchair users. Power wheelchair users with this tray will have the ability to deploy a tray when needed; however, when not in use, the tray can be stored on the wheelchair. The final tray design is
Tray For Wheelchair
CUSTOM ADAPTATION PURPOSE: To enable individuals with mobility disabilities to shop and carry items. Designed for use on a variety of wheelchairs, the tray was fashioned of PVC with a lip at the front made of aluminum angle to prevent items from falling off. The tray attaches to the wheelchair with Velcro for attachment and removal. TITLE: In the Basket. JOURNAL: TAD Journal. REF: Vol. 21 no. 2, Winter 2001: p. 17. PAGES (including cover): 2 2001.
Tray Stay Clamping System (Model 31085)
The Tray Stay Clamping System is lapboard mounting hardware designed to attach trays and lapboards to wheelchairs. The modular clamping system allows the user to adjust the height and position of the tray by attaching the base channel system to the tray and inserting the appropriate spacers. The clamps are secured by an attachment knob. The system can be used to mount trays directly to the wheelchair armrest and crossbar, the armrest pad, or to the manufacturer's Extenda-Arms, which provides ad
Trayaway
The Trayaway is a swing-away lapboard designed for use by individuals who use powered wheelchairs. This armrest tray is designed for a universal fit on most commercially-available wheelchairs. The unit provides a functional armrest with a built-in tray that folds out for the user without assistance for working on a laptop, writing, reading, or eating. It is also designed to safely support a laptop communication device. Other features include a transparent reading surface that can be tilted to su
Traymate
Plastic tray that fits on arm of wheelchair or upholstered chair. Perpendicular leg rests against inside of chair arm, adjustable spring loaded leg locks tray in place on outside of chair arm. Cut out for cups. 9 by 13 inch surface. Folds for storage. Washable. Fits also on hospital beds.
Trays & Hardware
The Tray and Hardware are a lapboard and mounting hardware designed for wheelchairs. The polycarbonate tray may be ordered with or without flip locks. Requires cutting out for trunk, sanding edges, and mounting of flip locks. OPTIONS: Tray elbow protection pads also available as individual or full pad. Mounting hardware may be ordered separately. DIMENSIONS: 18 x 24 inches (Small) and 24 x 27 inches (Large).
Trimline Comfortline Armrest Series
The Trimline Comfortline Armrest Series are add-on armrests and lapboards designed to provide a small writing or work surface for people who use wheelchairs. These wooden armrests are foam-padded and covered in satin finish vinyl. The armrests are available in fixed and flip-away styles for both right and left wheelchair arms and feature a molded cup holder recess. DIMENSIONS: .5 x 10.5 inches wide at the widest point, tapering to 6 inches x 22 inches. The foam padding is 1 inch thick. COLOR: Bl
Trimline Viewline Plus Armrest Series
The Trimline Viewline Plus Series are add-on armrests and lapboards designed to provide a small writing or work surface for people who use wheelchairs. Fabricated of transparent, unbreakable, scratch- resistant polycarbonate, the armrests are available in fixed or flip-away styles for both right and left wheelchair arms in tray only and tray with PVC plastic rim models. DIMENSIONS: 3/8 x 22 x 10.5 inches wide at the widest point, tapering to 6 inches. COLOR: The PVC plastic rims are black. WARRA
Trimline Woodline Light Reversible Armrest
The Trimline Woodline Light Reversible Armrest is an add-on armrest and lapboard designed to provide a small writing or work surface for people who use wheelchairs. The 7-ply Finnish birch plywood armrest has a clear lacquer finish and is designed to be assembled by the user in a right or left configuration. The necessary mounting hardware is included with the fixed model, Number 31302, and the flip-away model, Number 31309. DIMENSIONS: Both models are 3/8 inch thick x 22 inches deep x 10.5 inc
Triswitch Input Controller (Model 3450) & Varibrite Triswitch Display (Model 3460)
The Triswitch, in conjunction with three single-switch actuators, is used for mode selection and oepration of a Multimode Interface. Two of the switch actuators provide left and right actuator commands, while the third switch provides both forward and reverse commands. The display incorporates forward and reverse directional lights with corresponding arrows to provide a visual indication of forward/reverse switch selection. Five additional mode display light are provided to indicate when the Mul
Triton (Models Tr-24 & Tr-25)
The Triton, models TR-24 and TR-25, is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The wheel is made from computer machined 6061-T-6 polished billet aluminum with mirror bright surfaces, spin forged design, double walled rims, and sealed bearings. Hand rims are available with an anodized or vinyl-coated surface or with quad projection. DIMENSIONS: 24 inches (TR-24) or 25 inches (TR-25) diameter. CAPACITY: 250 poun
Triumph Mobility Escape Rollator
Triumph Mobility Escape Rollator is an ergonomic walker specifically designed for those with limited mobility due to arthritis, osteoarthritis, or a stroke. The Triumph Mobility Escape Rollator is available in 3 seat height adjustments to fit almost any user from 4 feet 7 inches to 6 feet 7 inches and has a compact folding system that is easy to fold with a simple lift of the lock release handle. In addition, you can partly fold the Escape to pass through narrow doors and spaces. This design ma
Truebalance
The TrueBalance is a wheelchair axle positioning system designed for use by clinicians and suppliers with people with mobility and lower extremity disabilities and spinal cord injury and others who use wheelchairs. It measures the stability of a person's wheelchair when occupied. The system allows a clinician or supplier to optimize the position of the rear axle which helps reduce rolling resistance, improve responsiveness, minimize impact from sidewalk cracks, and ease the ability to traverse c
Tube Arm Bracket Attaching System (Models 31902 & 31907)
The Tube Arm Bracket Attaching System is lapboard mounting hardware designed to secure trays to wheelchairs. These brackets enable a tray (not included) to slide on to tube-style armrests from the front. The brackets are attaached at both ends of the tube, enabling the tray to be attached to the top of the armrests (mounting hardware is not included). hook-and-loop straps (not included) may be used with these brackets for extra stability. OPTIONS: Mounting hardware (no. 31096H).SIZES: Small (no.
Turk Headswitch
The Turk head switch is designed for use by individuals with limited upper and lower extremity strength and coordination as result of cerebral palsy, stroke, and spinal cord injuries. The headrests contain either 1, 2, or 3 integral switches operated by pressure pads under the headrest cover.
U Form Deep Contour Back
The U Form Deep Contour Back is a foam back support cushion for use on wheelchairs. The segmented foam structure is available in multiple configurations allowing the back cushion to be built to meet the user's requirements. Sections can be removed, exchanged with other foam densities or removed to accommodate specific positioning needs. The segmented foam structure is formed with an additional 0.75-inch topper for added comfort and transition between the outer cover and the firmer inner foam seg
Uclamp Bundle (Wheelchair Umbrella Attachment Device)
The uClamp Bundle is a mounting clamp for wheelchair accessories designed for use by wheelchair users. The height-adjustable uClamp and extension pole enables the wheelchair user to have an umbrella attached to the clamp which, in turn, is fixed to either the frame of the arm or back section of a wheelchair or mobility vehicle. Each uClamp set comprises two clamps that work independently of each other. Both clamps are held together by a spindle and two tightening knobs, one at each end. Each ti
Ucosy Weathershield
The uCosy Weathershield is an umbrella for wheelchairs and strollers designed to protect a caregiver up to 6 feet, 4 inches tall pushing the mobility aid. The uCosy comprises a collapsible canopy made from durable nylon connected to telescoping poles fitted with uClamps (see also separate entry) capable of 360-degree rotation. Twin rotating uClamps attach simultaneously to the canopy poles and the structure of the wheelchair or stroller with the rotation controlled by simple turn-wheels. These c
Ultraslick Transfer Board
Transfer board to aid in transferring from wheelchair to bed or chair or toilet. Fiberglass laminated with hardwood. Lengths: 18, 24, or 30 inches. Available with or without hand holes on each end.
Unbreakable Cupholder Vertical Mount
The Unbreakable Cupholder Vertical Mount is designed for those individuals with lower extremity and neurological disabilities to help them by keeping their drinks more accessible. Securely attaches to vertical tubing on bedrails, wheelchairs, walkers, rollators. Durable fabric will not break.
Under Seat Wheelchair Pouch (Model 16C203)
The Under Seat Wheelchair Pouch, model 16C203, is an under seat pocket designed for wheelchair users. This device is designed to provide storage space under the chair and is accessible from the front by the wheelchair user. Made of nylon, it fastens with buckles. DIMENSIONS: (HxLxW) 12 x 11 x 16 inches.
Under The Seat Pouch
Under seat pocket measures 7 1/2 inches wide, 12 inches long, and 2 inches deep. Nylon. Velcro Closure. Attaches to frame under the seat with adjustable velcro straps to keep it hanging forward. Colors: black, red, navy, royal blue, tan, brown, and light or dark gray.
Universal Arm Mount (Model 347-Ua503)
The Universal Arm Mount, model 347-UA503, is a mounting clamp for wheelchair accessories designed specifically for attachment of the MYDESC EZ-Removable Arm (see separate entry). This metal clamp block can be used with wheelchair tubing from 0.75 to 1.25 inches in diameter, and provides a 0.78 inch cylinder slot for mounting the EZ-Removable Arm directly to the wheelchair frame. The clamp may be mounted either horizontally or vertically.
Universal Carry All
The Universal Carry All is a carrying bag for walkers designed to provide carrying capability for people with mobility disabilities. This heavy-duty nylon pouch secures to walker crossbars, wheelchairs, and bed rails and features one large compartment, a security pocket and eyeglass pouch, and a keypouch with cord. DIMENSIONS (WxL): 18.75 x 11 inches.
Universal Headrest Mounting Plate (Model 7730)
The Universal Headrest Mounting Plate is seating hardware designed for use with wheelchair headrests. This plate enables a variety of headrests from various manufacturers to be interchanged as needed. The headrests may be changed without having to redo the T-nuts in the back.
Universal Support Arm (Usa) (Model F70660)
The Universal Support Arm (USA), model F70660, is an extension arm for wheelchair accessories that clamps to the wheelchair's tubing. The basic arm is made of telescoping aluminum tubing that allows rotational and axial adjustment. Tube collars clamp by integral locking knobs. Angle adjustments are made at two U-clamp joints. Knobs are also used to lock the holder at any angle. The arm has a camera support with a 1/4-20 thread that fits standard 35mm camera thread wells. Included is a hardware p
Universal Tote (Models Ez0101 & Ez0102)
The Universal Tote is a carrying bag for a walker or a wheelchair side pouch designed for use by individuals with mobility or walking disabilities or spinal cord injury. Made of nylon, this pack attaches with two adjustable straps to the front of a walker, and the smaller size (model EZ0102) attaches to the armrest of a wheelchair. An inner pocket can be accessed by opening a full-length zipper. There are two (model EZ0101) or three (model EZ0102) pockets on the outside. SIZES: Large (model EZ01
Unreal Lambskin Wheelchair Accessories
Unreal Lambskin Wheelchair Accessories are decubitus pads for various pressure points including the seat, back, arm and footplates. These covers are made of synthetic fleece for pressure relief and prevention of decubitus ulcers. The material consists of 3/4-inch pile and is stain resistant, nonflammable, nonallergenic, nontoxic, machine washable and dryable, and resists packing down. Foot plate, arm and removable desk arm pads are sold in pairs. BACK COVER: Fits all standard adult wheelchair mo
Upholstered Padded Armrests (Model 65)
The Upholstered Padded Armrests, model 65, are wheelchair armrest pads designed for use with wheelchairs with full- or desk-length armrests. COLOR: Upholstered to match color of seat and back upholstery.
Uplift Stumprest Pack (Model Srpack)
The Uplift StumpRest Pack, model SRPACK, is an amputee leg support designed for use on wheelchairs by individuals with below-knee amputation. The StumpRest unit comprises a universal cross-frame drop-base with a moisture-proof ABS plastic top with retractable sliders that accommodate right, left, or dual amputations. The pack includes a choice of StumpRests (model SR 16, model SR 18, or model SR 20, one standard foam slider cushion, and two Versa Lock drop hook retainers (all components are also
USB Cable (long)
This USB Cable (long) is a longer version of the USB cable for users to recharge their Tecla Shield DOS. It is designed for recharging the Tecla Shield without having to detach it from the users chair.
USB Charger / Power Port for Power Wheelchairs
The USB Charger/Power Port for Power Wheelchairs is designed for wheelchair users. To use, plug the device into the wheelchairs charge port, connect a USB cable to the device, and charge or power the device. This works for nearly all USB devices, including Android phones and tablets, iPhones, iPads, USB fans, USB lights, and more. This will not prevent your wheelchair from driving like battery chargers do.
Utility Clamp For Wheelchair Accessories (Model H70673)
The Utility Clamp for Wheelchair Accessories, model H70673, is a mounting clamp that attaches to the frame of wheelchairs 7/8-inch in diameter. A thumb screw holds the clamp securely. A parallel hole accepts a 3/8-inch diameter rod, and the set screw is turned with a knurled knob. The clamp is made of ABS plastic.
Valueview Tray (Model 3115)
The Valueview Tray, model 3115, is a lap tray designed for use with wheelchairs. Made of transparent, unbreakable polycarbonate, this tray features an aluminum rim and hook-and-loop attachment straps. DIMENSIONS (WxD): 23.5 x 19 inches. The straps are one inch wide. The tray is 0.25-inch thick. WARRANTY: This product is warranted against defects in workmanship and materials for 90 days from the date of purchase.
Variable Speed Control (Model 10-1A) & 2 Speed Control (Model 10-12)
Electrical control, designed for LaBac Systems recline systems allows speed of recline unit to vary from full speed to 50% speed. Maintains full torque at low speeds to accommodate heavier users. Speed control module has complete attendant switches plus a receptacle to plug in user control switch. 2 speed control has speed set at either 100% or 50%.
Varibrite Mode Display (Model 2775-4)
A remote display used in conjuction with a Multimode interface to indicate when the system is in standby, or in one of four oeprating modes. The display is mounted on a flexible gooseneck to position the display for optimum viewing, and to help protect the display from impact damage. The gooseneck is fitted to a mounting tube for attachment to an armrest using a standard hand-control clamp.
Varilite Solid Insert
The Varilite Solid Insert is a solid seat insert designed for use in wheelchairs by individuals with lower extremity disabilities, mobility disabilities, and spinal cord injury. This insert is placed between the cushion and upholstery or directly inside the cushion cover to eliminate the effects of sling upholstery. Inserts are available to accommodate pediatric as well as adult users. They are made from durable plywood with rounded edges and sanded surfaces to reduce chance of splintering or pu
Velcro Closure Armrest Mount For Lapboard (Model 08-1000)
Lapboard with velcro closure, mounts on armrest. 1/4 inch clear acrylic. Sizes: 26 by 24 inches with 15 by 19 inch body cutout, 24 by 24 inches with 15 by 9 inch body cutout, 22 by 22 inches with 13 by 7 1/ 2 inch body cutout, 20 by 20 inches with 10 by 6 inch body cutout. Modifications and accessories: 3/8 inch acrylic, colored acrylic, 1/4 inch lexan, 1/4 inch ABS, special cutouts, special widths and depths, aluminum rim, plastic rim, communication overlay.
Velcro Closure Safety Strap For Wheelchairs (Model H70623)
The Velcro Closure Safety Strap for Wheelchairs, model H70623, is a wheelchair seatbelt made of Velcro closure with metal D-ring buckles. The belt is adjustable, washable, and can be sterilized. The strap can be positioned at various heights to insure user comfort and security. A short strap anchors to the wheelchair frame while the long strap adjusts in length. DIMENSIONS: 32 inches long x 2 inches wide.
Velcro Closures Armrest Mount, Birch Lapboard (Model 08-4000)
Lapboard of birchwood with waterproof seal and plastic rim. Armrest mounting, velcro fasteners. Sizes: 24 by 24 inches with 15 by 9 inch body cutout, 22 by 22 inches with 13 by 7 1/2 inch body cutout, 20 by 20 inches with 10 by 6 inch body cutout. Custom cutouts, widths and depths available.
Velcro Seatbelt Alarm (Models Mdt5500 & Mdt5500L)
The Velcro Seatbelt Alarm is a wandering patient system designed for use by individuals with Alzheimer's disease or cognitive disabilities. This restraint-free seatbelt alarm notifies caregivers when an individual tries to get out of a wheelchair unattended. The seatbelt has a Velcro closure and a self-release pull strap, and mounts directly to the wheelchair frame. When the Velcro on the belt is disconnected, the alarm sounds, notifying the staff that the patient is trying to exit the chair. P
Velcro Style Positioning Belt (Model 90133115)
The Velcro Style Positioning Belt, model 90133115, is a wheelchair seat belt designed for use by individuals with mobility and lower extremity disabilities or spinal cord injury. This belt is made of adjustable nylon webbing with a Velcro fastener, and mounts to the chair back at waist level. The attaching hardware is included. DIMENSIONS (LxW): 48 x 2 inches.
Velcro Wheelchair Straps (Models 107, 109, & 700)
Velcro wheelchair straps. 4 inches wide, various lengths. Constructed with stainless steel cinch ring and metal grommet for chair attachment. Includes storage feature for when not in use.
Ventilator Trays (Models 08-Pe, 08-Pi, 08-Pj, & 08-M)
Adjustable ventilator or respirator support tray mounts under the wheelchair seat between the rear tires. Model 08-P is a pull out model for power recliners, has 16 inches of travel; battery box holds batteries for wheelchair and back up battery for ventilator; available for Everest & Jennings or Invacare power recliners with LaBac Systems seating systems. Model 08-M is a lift out model for manual wheelchairs; rests on lower rail of chair, is 13 inches wide and 23 inches long with a one inch
Vertical Tray
DO IT YOURSELF ENTRY --- PURPOSE: To hold object in view for an individual who is unable to move her neck to look down at a wheelchair tray. A vertical tray was made of wood that attached to the existing tray with quick-release clamps. The tray has vertical wings on each side to keep objects from falling off. The tray can be adjusted forward and backward for proper positioning. A clear plastic shelf was installed in slots on the tray and can be adjusted up or down for optimal viewing. TITLE: The
Viamobil
Viamobil is an attendant operated wheelchair brake and power assist designed for use by caregivers of individuals with mobility or severe hhysical disabilities or spinal cord injury. This pushing and braking aid is used exclusively by the person escorting the occupant of the wheelchair. It assists the caregiver to push and brake the wheelchair, and can overcome slopes of up to 18 percent. The unit is attached to the bracket on the wheelchair. The caregiver presses the drive lever to commence dri
Viewline E-Z Lock Quik-Fit Trays (Models 33000P, 33001P, 33002P, 33017P, 33000, 33001, 33002, & 33017)
The Viewline E-Z Lock Quik-Fit Trays are lap trays designed for use with wheelchairs. These trays feature an E-Z Lock Clamping System that adjusts for standard or thick arm pads, enables the tray to slide on to the armrests from the front, and secures the tray with a simple locking motion. The moisture-resistant Viewline Trays are made of transparent unbreakable polycarbonate. Models 33000P, 33001P, 33002P, and 33017P have a black PVC rim. The other models do not have a rim. SIZES: Child (fits w
Viewline Plus Extended Wing Trays (Models 31226, 31224, 31227, & 3125)
The Viewline Plus Extended Wing Trays are lap trays designed for use with wheelchairs. These moisture-resistant Viewline Trays are made of transparent unbreakable polycarbonate. Models 31226 and 31227 have a black PVC rim. The other models do not have a rim. The extended wings are designed to fit around the back uprights of the chair and they accommodate growth. SIZES: Small and large. DIMENSIONS (WxD): The small models (nos. 31224 and 31226) are 19.5 x 23.5 inches with an 11.5-inch wide torso c
Viewline Plus Series
The Viewline Plus Series are lapboards designed for attaching to wheelchairs. These trays are fabricated of transparent, unbreakable, scratch-resistant polycarbonate, and are available in tray only, tray with rim, tray with straps, and tray with rim and straps models. The juvenile tray has an oblong work surface; all other trays are rectangular. OPTIONS: Tray rims are available in a choice of anodized aluminum or PVC plastic. SIZES: All models are available in child, juvenile, adult, and extra-w
Viewline Series
The Viewline Series are lapboards designed for use by people who use wheelchairs. Constructed of transparent polycarbonate, models include the tray only, tray with anodized aluminum rim, tray with straps, tray with rim and straps, and the tray with the Quad Care Attaching System (see separate entry). The juvenile tray has an oblong surface; all other trays are rectangular. SIZES: The tray with the Quad Care attaching system is available in an adult size only; all other models are available in ch
Viewline Top Drop Quik-Fit Trays (Models 33006P, 33008P, 33010P, 33013P, 33006, 33008, 33010, & 33013)
The Viewline Top Drop Quik-Fit Trays are lap trays designed for use with wheelchairs. These trays feature a Top Drop Clamping System that enables the tray to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. The moisture-resistant Viewline Trays are made of transparent unbreakable polycarbonate. Models 33006
Viewline Top Drop Quik-Fit Trays With Control Cutouts (Models 33025, 33026, 33027, 33028, 33029, 3330, 33031, 33032, 33033, 33034, 33035 & 33036)
The Viewline Top Drop Quik-Fit Trays with Control Cutouts are lap trays designed for use with powered wheelchairs with joysticks and other controllers. These trays feature a Top Drop Clamping System that enables the tray to be positioned straignt down on the armrests and requires only 3/8-inch clearance under the armpad which enables the tray to be used when a joystick or other control is mounted next to the armpad. The tray locks on with the turn of a handle. These trays also feature a cutout i
Vortex
The Vortex is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The wheel is CNC precision machined from aircraft quality aluminum billet. It has 3 spoke design, and each spoke has a 3-circle design so that the wheel resembles an automobile's steering wheel. DIMENSIONS: 24- or 25-inch diameter. The width is 1 inch. CAPACITY: 250 pounds. WEIGHT: 3.4 pounds. COLOR: Hub and rim are polished aluminum. Spokes are anodized g
Walker / Wheelchair Bag
The Walker/Wheelchair Bag is a carrying bag for a walker or a wheelchair back pouch designed to enable persons with mobility disabilities to transport personal items. Made of plastic-coated nylon with cotton binding, the bag features two reinforced pockets and attaches to the walker or wheelchair using hook-and-loop fasteners. The bag is mildew and fungus resistant and can be machine washed and dried. DIMENSIONS (LxH): 22 x 10 inches. COLOR: White.
Walker / Wheelchair Bag (Model M2930)
The Walker / Wheelchair Bag, model M2930, is a lightweight canvas bag that attaches to a walker or wheelchair and features outside compartments with a fold-over flap. COLORS: Asssorted.
Walker And Wheelchair Bags
The Walker and Wheelchair Bags are designed to provide carrying assistance for people who use whelchairs or walkers. All styles are made of washable packcloth (400 denier nylon with a waterproof coating) and feature Velcro straps to hold them in place. The Style A Walker Bag ($25) secures to the front bar and and legs of the walker with five Velcro straps and features flap closure and inside compartments. Style B ($15) is a saddle-bag style pouch and secures to the side of a walker or over a wh
Walker Carrier
CUSTOM ADAPTATIONPURPOSE: To enable an individual with mobility disabilities to carry a walker on a wheelchair. Designed for a wheelchair with two horizontal push bars on the back, the carrier is comprised of two sets of hooks that fit over the bars. Using extruded aluminum bars, two shorter hooks and two longer hooks were created by placing the aliminum bar in a vice and bending it to a 90-degree angle and then hammering out two pairs of curved shapes. The longer pair of hooks fit over the top
Walking And Wheeling
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To allow a child to be securely fastened in a wheelchair with an adapted sleeve covering the seatbelt, making it difficult for the child to unfasten the seatbelt.
Weatherbee Power Chair Cover
The WeatherBee Power Chair Cover is designed to protect powered wheelchairs from dust or moisture during transport or storage. To use, slip the cover over the wheelchair and secure underneath using the locking drawstring. Grommets are also provided for additional fastening. The cover is available in standard or heavy-duty models. SIZES: Regular, large, extra large, or tall. DIMENSIONS(HxWxL): The regular cover is 38 x 18 x 44 inches. The large cover is 38 x 23 x 44 inches. The extra large cover
Weatherbreaker, The
The WeatherBreaker is a canopy for scooters designed to protect individuals who use scooters from the weather. This canopy is available in standard, vented, and maximum protection styles. The standard model is made of solid fabric. The vented model has mesh material on the sides and back instead of solid fabric to provide more ventilation for heat protection while still sufficiently protecting from sunlight and rain. The maximum protection model is the same as the vented model with the addition
Wheel-Ease Rim Covers (Model 74612)
The Wheel-Ease Rim Covers, model 74612, are handrim covers designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. Designed to fit over the hand rims of the push wheels of manual wheelchairs, these covers improve the user's grip on the rim to make manual propulsion of the wheelchair easier. Designed to be an alternative to gloves, these covers have a smooth finish that protect against calluses and injury. The covers can
Wheel-Ease Wheelchair Rim Covers (Model 926514)
The Wheel-Ease Wheelchair Rim Covers, model 926514, are handrim covers designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. These covers are designed to improve traction, promote proper hand placement, and cushion the hands when the user is propelling a manual wheelchair. Features include thermal insulation shields and a smooth finish to protect hands from cold metal rims. The covers are made to fit standard 24-inch w
Wheelblade Xl
Wheelblades, which resemble mini skis, are designed to be locked onto the front wheels of a wheelchair to spread weight over a greater surface area covered with snow. Wheelblades contact surface distributes the wheelchair driver’s pressure evenly onto the ground and prevents the small front wheels from sinking into the snow. The blades run over the ground with very little pressure and have no problem smoothing out rough spots. Two tracking channels on the Wheelblades underside compress the snow
Wheelchair / Walker / Scooter Bag
The Wheelchair / Walker / Scooter Bag is a caddy, or carrying bag, for wheelchairs, walkers, and scooters designed for individuals with mobility, balance, and walking disabilities or spinal cord injury. This bag attaches using adjustable straps and clip fasteners. Made of 100 percent cotton duck with Velcro closure, this bag features an outside pocket with a zippered compartment to store a cell phone and interior slots to store credit cards and identification. For wheelchair use, the bag can be
Wheelchair / Walker Pouch (Model 16C002)
The Wheelchair / Walker Pouch, model 16C002, is a wheelchair side pouch and a carrying bag for walker designed for use by people with balance, lower extremity, mobility and walking disabilities, spinal cord injury and others who use a walker or wheelchair. Made of leatherette material, this pouch features a single pocket for storage of magazines or other small items. The pouch attaches over a cross bar and is held in place with dome snaps. The pocket fastens with Velcro closure. DIMENSIONS (LxW)
Wheelchair Activity Arch
This Wheelchair Activity Arch is designed for use by children and adults with limited upper extremity strength and coordination as a result of neurological involvement, spinal cord injuries, or nerve injuries that impact movement. It is designed to encourage reaching, grasping, and pulling. Clips onto most wheelchairs and the five velcro straps are provided to suspend toys (not included).
Wheelchair Activity Frame
The wheelchair activity frame is a great motor activity tool for children or adults in a wheelchair, pushchair or stroller. The wheelchair activity frame clips onto the frame of the wheelchair and fits most models. Five velcro straps are provided to suspend toys and the user can choose from a variety of tactile and sensory toys to hang for ongoing fun throughout the day.
Wheelchair Arm Pouch (Model 16C003)
The Wheelchair Arm Pouch, model 16C003, is a wheelchair side pouch designed for use by wheelchair users. The pouch is designed to fit wheelchairs with desk-length arms and can also be used with walkers. It is made of leatherette material. DIMENSIONS: 8 x 9 inches.
Wheelchair Arm Protectors
The Wheelchair Arm Protectors are wheelchair armrest pads designed to prevent skin irritation for individuals who use wheelchairs. Made of polyester and acrylic fabric, these pads wraps over the wheelchair arm with Velcro attachments. SIZES: Full length (fits arm rest measuring 13 to 15 inches) and desk length (fits arm rests measuring 8 to 11 inches).
Wheelchair Armrest Cushions (Models 703015, 703016, & 703130)
The Wheelchair Armrest Cushions are wheelchair armrest pads designed for use by individuals who use wheelchairs. These foam-padded nylon-covered pads attach to the armrests with Velcro fasteners and provide protection against pressure sores and comfort for sensitive arms and elbows. Model 703015 is designed for chairs with full-length arms and model 703016 is designed for chairs with desk-length arms. Model 703130 is an extended cushion that extends beyond the armrest and covers the armrest post
Wheelchair Bac Pac (Models Wh165L & Wh165S)
The Wheelchair Bac Pacs are waterproof back pouches made of nylon with lock proof velcro straps for securing it to the handgrips of wheelchairs and easy access closures. Both the longer (WH165L) and shorter (WH165S) models offer small inside pockets for greater organization. DIMENSIONS: Model WH165L is 18 (h) x 16 (w) x 5 (d) inches; model WH165S is 12 (h) x 16 (w) x 5 (d) inches.
Wheelchair Back Carryon (Model Ez0060)
The Wheelchair Back Carryon, model EZ0060, is a wheelchair back pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made of weather-resistant nylon, this tote attaches using loop handles that slip over the wheelchair handles. The Wheelchair Back Carryon has large deep pockets. DIMENSIONS (HxLxW): 4.5 x 17.5 x 16.5 inches. COLOR: Black.
Wheelchair Back Pack, Vinyl (Model 16C004)
The Wheelchair Back Pack, Vinyl, model 16C004, is a wheelchair back pouch designed for use by wheelchair users. This large leatherette bag has a weather flap and an inside pocket. The bag accommodates large items such as sweaters, blankets, or larger daily living aids. DIMENSIONS: (LxW): 17 x 16 inches.
Wheelchair Back Support
The Wheelchair Back Support is a lumbar back support cushion designed to provide firm back support for wheelchair users. Covered in stain-resistant velour, the half-moon-shaped support is formed of quick-recovery foam and attaches to the wheelchair using loop handles. DIMENSIONS (LxWxD): 16 x 8 x 3 inches.
Wheelchair Backpack & Bookbag
Wheelchair back pouch 16 inches high, 15 inches wide and 7 inches deep. Children's size measures 12 by 12 by 5 1/2 inches. Cordura nylon. Two styles: Backpack has one large compartment with padded bottom. Bookbag has two compartments. Both have velcro closure and attach to handgrips with loops. Colors: black, red, navy, royal blue, tan, brown, and light or dark gray. Multicolor bags available.
Wheelchair Bag
CUSTOM ADAPTATION PURPOSE: To provide a means for a caregiver to carry items while pushing a wheelchair. A customized vinyl bag was made and held open and supported by a galvanized wire frame sewn into the top edge. A flap top and a return around the front and side edges protect the contents from the weather. Handles on each side of the center of the bag provide a means of carrying the bag away from the chair. Small straps made of the same material as the bag loop around the push handles of the
Wheelchair Bag (Model B2925)
The WheelChair Bag, model B2925, is a canvas bag with a front pocket and a velcro closure strap. COLORS: Assorted.
Wheelchair Bag (Models St130A, St130B & St130C)
The Wheelchair Bag, models ST130A, ST130B & ST130C, is a carrying bag designed for use by individuals with physical disabilities. The bag can be easily put on the arm of a wheelchair or the front of a walker. o a walker, and is made from medium weight canvas. Model ST130A has a side pocket. Model ST130B is the same as ST130A but has no pocket. Model ST130C has no pocket but is equipped with velcro straps. OPTIONS: Silk screening with a logo or message is available in a variety of colors. DIM
Wheelchair Bag.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Bag which can be fastened over the arm of a wheelchair to carry small items. Pattern and instructions for a bag with straps, a side pocket and a zipper top, made with 1/2 yard of firm fabric, binding tape, tape or braid for the straps and a 12 inch zipper. SKILLS REQUIRED: Sewing. AUTHOR: Kernaleguen, A TITLE: Clothing Designs for the Handicapped REF: Edmonton, Alberta, Canada: University of Alberta Press: p 222-225 NARIC CALL NUMBER: R0866 PAGES (incl
Wheelchair Belt (Models Mdt825090 & Mdt825091)
The Wheelchair Belt is a wheelchair seatbelt designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. This belt can be permanently attached to a wheelchair or geriatric chair without the use of tools. The belt is made of durable, latex-free nylon webbing with a hook and loop closure (model MDT825090) or a quick release buckle (model MDT825091).
Wheelchair Belt Buckle Covers
Wheelchair Belt Buckle Covers is designed to prevent children and adults with cognitive disabilities who use wheelchairs from unlocking a wheelchair seat belt. Wheelchair Belt Buckle Covers offer a range of added security for patients who wear a push-button style of positioning belt by limiting the access to the button. Standard access buckles that are not limited are also offered as replacements for those that already come with the belt.
Wheelchair Beverage Holder (Model Ad-500)
Clip on drink holder. Vinyl coated metal clips attach to wheelchair desk arms. Holder is lightweight plastic with adjustable Velcro closure to accommodate various sized containers.
Wheelchair Bike, The
The WheelchairBike is a cycle attachment for wheelchairs designed for use by individuals with mobility disabilities. This maintenance-free wheel and pedal assembly is intended for use by individuals with limited or no use of their legs, attaches to the front of most 18- and 20-inch wheelchairs, and can be maneuvered by shifting body weight. The unit has a steel frame, no wearable parts, and wheels that roll on high-speed bushings. WEIGHT: 16 pounds. GUARANTEE: Lifetime guarantee.
Wheelchair Blanket With Pockets -- Non Slip -- Burgundy
The Wheelchair Blanket with Pockets – Non-Slip is a blanket designed for those who use a wheelchair. Two side pockets and one middle pocket. Hook and loop tabs to keep blanket securely attached. 95 percent polyester, 2 percent nylon.
Wheelchair Book Bag
DO IT YOURSELF PURPOSE: To provide powered wheelchair users with carrying capability. Use a standard soft briefcase or carry-on luggage bag that fits securely on the battery shroud of a powered wheelchair and is equipped with both hand carrying handles and a shoulder strap. Unhook one side of the shoulder strap, and thread the strap around the bottom of the back canes of the seat. Refasten the shoulder strap to the side of the briefcase. If the wheelchair is equipped with a tilting seat, the c
Wheelchair Briefcase
Wheelchair back pouch is a pedded, legal size bag. Cordura nylon. Two large compartments, one divided for pens, etc. Attaches to handgrips with loops that fold out of way when not in use. Colors: black, red, navy, royal blue, tan, brown, and light or dark gray.
Wheelchair Bumper Bar
CUSTOM ADAPTATION PURPOSE: To protect walls and furniture from being damaged by a wheelchair when the user has his/her legs straight out. With the user's legs straight out, the space taken up was large and made it difficult to avoid bumping into walls and furniture. To protect both the user's feet and surroundings, a frame that sits upright at the end of the chair was constructed of PVC tubing. The frame was covered in cellular foam and a strip of outdoor furniture fabric was laced around the f
Wheelchair Caddy
The Wheelchair Caddy is a carrying caddy designed for use by individuals who use wheelchairs. It mounts on the left or right side of most wheelchairs with an adapter and clamps (included). This caddy features three deep plastic wells to hold a wide variety of items, including beverages, food, pens, notebooks, and glasses. It can also be rotated to a variety of positions. A 12- ounce, microwave-safe beverage mug with a non-spill lid is included. DIMENSIONS (WxHxD): 12 x 3.5 x 7 inches. WARRANTY:
Wheelchair Camera Mount
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom wheelchair camera mount for a photographer with hemiplegia related to stroke and limited use of his right arm. This individual cannot simultaneously hold his camera firmly and press the shutter, particularly as he uses large lenses which are quite heavy, and using a tripod to hold the camera doesn’t work either, as it’s difficult to set this up with one hand. Therefore, a custom adaptation solution of creating a wheelchair camera m
Wheelchair Canopy
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To provide a custom adapted wheelchair canopy to be used by an individual with light sensitivity and mobility disabilities on her wheelchair and also be portable to fit on public vans, buses, and/or taxis. The canopy is designed to work on almost any wheelchair/cart and be capable of travel. Windows could be added for those more interested in rain and snow protection. The frame is made from steel and aluminum tubing. Scaled drawings are available upo
Wheelchair Carry All (Model Mf70616)
The Wheelchair Carry All, model MF70616, is a wheelchair back pouch designed for use by individuals with lower extremity and mobility disabilities or spinal cord injury. Made of waterproof nylon with a rigid bottom liner, this bag attaches to the wheelchair’s handgrips with durable nylon straps. The bag has a top flap that closes with a hook-and-loop closure and a full width inner pocket for storing items such as carts, books, groceries or school supplies. DIMENSIONS (HxDxW): 14 x 4 x 14 inches.
Wheelchair Carry-All (Model 70616)
The Wheelchair Carry-All, model 70616, is a back pouch designed to attach to the handgrips of wheelchair push handles. This bag is made of waterproof denim with a rigid bottom liner and webbing straps. The caddy has a full-width pocket inside and a top flap that has a Velcro closure. DIMENSIONS: 14 x 14 x 4 inches.
Wheelchair Carry-On (Model 2503)
The Wheelchair Carry-On, model 2503, is a wheelchair back pouch designed for use by individuals with mobility disabilities or spinal cord injury. This pouch has adjustable straps that fit over the push handles of a wheelchair and large, deep pockets. The pouch is made of water-resistant nylon. DIMENSIONS (HxLxW): 17.5 x 4.5 x 16.5 inches. COLOR: Black.
Wheelchair Cart.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Two wheeled cart attaches to wheelchair, carries up to 45 pounds . A flexible hitch allows cart to swing directly alongside the side of wheelchair so wheelchair rider can load and unload cart independently. Four diagrams, 5 photographs, materials list and construction details. Estimated cost $ 15, estimated construction time 5 hours. Includes several hitching arrangements for different wheelchair models. SKILLS REQUIRED: Woodworking. AUTHOR: William Su
Wheelchair Caster Glides
DO IT YOURSELF ENTRY --- PURPOSE: To protect walls and doors from damage from powered wheelchair casters. By mounting a disc of ultra high molecular weight polyethylene(UHMW) on the caster spindle where it meets the top of the fork, impacts are deflected. The UHMW disc prevents gouging and does not mar the woodwork. For additional protection from axle gouging, a deflector can be mounted on the axle ends. TITLE: Wheelchair Caster Glides. WEB SITE: Workshop Solutions at http://www.workshopsolutio
Wheelchair Computer Tray
DO-IT-YOURSELF ENTRY --- PURPOSE: To create a computer work table for a wheelchair. The table surface is made of plywood and positions a laptop computer directly in front of the user. The table is angle-adjustable and pivots out of the way or can be removed for transfers or when not in use. The table is supported by a pole and support made of threaded pipe. MATERIALS: Plywood and threaded pipe. TOOLS: Shop tools. SKILLS REQUIRED: Basic shop skills. TITLE: Doing It Yourself. JOURNAL: Quest. REF:
Wheelchair Control Cover
CUSTOM ADAPTATION PURPOSE: To protect powered wheelchair controls from rain. A sleve was fashioned from clear plastic that slides over the wheelchair joystick controller, protecting the buttons an gauges and most of the joystick. A fole in the sleeve provides access to the joystic to enable the chair to be operated. TITLE: Bathroom Assistance. JOURNAL: TAD Journal. REF: Volume 26, Number 2, July 2006: p. 12-13. PAGES: 3 (including cover).
Wheelchair Cover.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Absorbent terry cloth seat cover for wheelchair. Use towel 40 by 24 inches. Fold towel in half widthwise right sides together. Stitch 1/2 inch from foldline to form casing. Thread twill tape through the casing to tie behind chair. More twill tape and snaps are used to secure the cover to the chair. Includes picture. SKILLS REQUIRED: sewing. AUTHOR: Kernaleguen, A. TITLE: Clothing Designs for the Handicapped. REF: Book: University of Alberta Press, Albe
Wheelchair Covering
The Wheelchair Coverings are decubitus pad and seat covers, armrest and legrest pads for wheelchairs designed for use by individuals with lower extremity and mobility disabilities, spinal cord injury and others who spend most of their time in wheelchairs. Made from Hitemp, urine resistant medical sheepskin, these pads help reduce the risk of pressure sores and ulcers and body aches. The pads are made separately to fit the seat, back and arms of the wheelchair. They are washable and are available
Wheelchair Cup Holder
The Wheelchair Cup Holder is a wheelchair drink holder designed for use by individuals who use wheelchairs. This holder can be attached vertically or horizontally on the right or left side. Side opening enable the unit to accommodate mugs with handles.
Wheelchair Cup Holder (model # F706220001)
Wheelchair Cup Holder is a plastic cup holder that has slotted on two sides to hold a cup with handles and is accessible to left or right-handed people. It can also hold a glass, can or bottle, including mugs with handles. The plastic clamp has a large easy-to-tighten lever knob. The clamp fits a 1 inch (2.5 centimeter) diameter tube and comes with a sleeve to reduce it to fit 7/8 inches (2.2 centimeter) tube frames.
Wheelchair Cup Holder (Model F70622-0001)
The Wheelchair Cup Holder, model F70622-0001, is a wheelchair drink holder designed for use by individuals who use wheelchairs. This unit also clamps to walkers, rollators, bed rails, and other tubular frames and is equipped with a large lever knob to secure the clamp. The attached plastic holder holds glasses, cans, bottles and it is slotted on two sides to accommodate cups with handles. The holder is is accessible for use by right- or left-handed users. DIMENSIONS: The holder is 3.5 inches hig
Wheelchair Day Pac (Model Wdp12)
The Wheelchair Day Pac, model WDP12, is a wheelchair back pouch carrying accessory. Made in the USA of highly durable nylon fabrics with nylon tape bonded seams, this bag attaches to fit any chair with its Slipstrap System. Two pull rings allow for easy opening. DIMENSIONS: 12 x 12 x 4 inches. WARRANTY: Repair or replacement guarantee.
Wheelchair Day Pack
The Wheelchair Day Pack is a wheelchair back pouch designed for use by individuals who use wheelchairs. Made of weather-resistant nylon packcloth, this pack features a large capacity main compartment and roomy front zippered pockets. The bag hangs on the wheelchair push handles and has reflective tape for greater visibility. DIMENSIONS: The main compartment is 13.75 x 12.5 x 5 inches. The front compartment is 13.75 x 10.5 x 3.5 inches. COLOR: Royal.
Wheelchair Day Pack
The Wheelchair Day Pack is designed for wheelchairs users with mobility or lower extremity disabilities or spinal cord injury. The large bag can store bulky items such as jackets and notebooks and additionally it has two interior slash pockets for tucking away smaller items. Additionally, the bag can hang on push handles and web straps easily adjust to fit most 15 to 24 inch wheelchairs with push handles.
Wheelchair Double Leg Strap (Model 7017)
The Wheelchair Double Leg Strap, model 7017, is a legrest strap designed to prevent the feet of wheelchair users from slipping off of the footplates. The straps are made of strong poly webbing with a Velcro closure. The two straps with connecting straps attach to the wheelchair leg assemblies. SIZE: Fits standard adult or narrow adult wheelchairs. COLOR: Black.
Wheelchair Dust Covers (Models F70651-0036 & F70651-0048)
The Wheelchair Dust Covers are clear vinyl covers with cotton bindings designed to protect chairs from dust and dirt when not in use. DIMENSIONS: Model F70651-0036 is 36 x12 x 36 inches; model F70651-0048 is 34 x 12 x 48 inches. Any size of cover can be made to order.
Wheelchair Evacuator
The Wheelchair Evacuator is designed to attach to most manual wheelchairs to facilitate the safe evacuation of wheelchair users in an emergency evacuation. Not only does the Wheelchair Evacuator provide an alternative to most evacuation chairs it also provides evacuations of the wheelchair user in their own wheelchair, thus eliminating the need to move the wheelchair user into an evacuation devise.Evacuation of the wheelchair user up stairs. Evacuation of the wheelchair user to a place of safety
Wheelchair Fenders
DO IT YOURSELF PURPOSE: To provide powered wheelchair users with protection from water and road grime. These fenders are designed for use on 10 x 3 inch rear drive wheels are originally intended for use on go-carts and mini bikes. An existing screw that secured the wheelchair shroud is used to secure the fender and existing holes designed to enable the length of the wheelbase to be adjusted are used for the screws. If the rear of the fender is wider than the front lip where it mounts, the side
Wheelchair Footplate Adaptation
CUSTOM ADAPTATION PURPOSE: To assist an individual with mobility disabilities in transferring from a wheelchair. The wheelchair had a one-piece footplate that folded up during transfers and down to provide foot support. However, the user was unable to change the position of the plate as needed. The existing footplate was removed and replaced with hinged dual footplates. The new footplates were made from sheet aluminum cut to shape, with large overlaps joined with epoxy resin and pop-rivited for
Wheelchair Footstrap
DO IT YOURSELF ENTRY --- PURPOSE: To keep a wheelchair user's feet off the floor after footrests have been removed to avoid striking door jams and walls. Obtain about 42 inches of strong nylon strap (similar to that found on luggage) and wood dowelling that will fit into the hollow part of the wheelchair footrest fastener. Cut the dowel to fit each opening. Attach the strap with a screw to the top of each dowel. MATERIALS: 42 inches of nylon strapping, wood screws, and wooden dowel. TOOLS: Saw a
Wheelchair Four Point Seat Belt - Auto Buckle (Models 16C138S, 16C138M & 16C138L)
The Wheelchair Four Point Belt Seat Belt - Auto Buckle, models 16C138S, 16C138M & 16C138L, is a wheelchair seatbelt designed to provide security and positioning assistance for wheelchair users and those suffering with posterior and anterior pelvic tilt, and pelvic rotation and thrusting. Designed with 2-inch webbing with fastening tabs for mounting, this belt is equipped with a center pull and four point secondary straps for preventing shifting during thrusting, wiggling, or sliding movement
Wheelchair Fx Wheelchair Light Kits
Wheelchair FX Wheelchair Light Kits are wheelchair lights designed for use by individuals with mobility disabilities. A Basic Safety kit and two Red-White-And-Blue kits are available. The Basic Safety kit includes five extremely low draw LED light strips: two for the armrests, one for the back of the frame, and two for under each seat corner. The Red-White-And-Blue kits include an additional strip for the back plus one for the front, along with LightingFX, a on/off remote control with multiple f
Wheelchair Glider
The Wheelchair Glider is a rocking or glider platform for a manual wheelchair that is designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. A person in a wheelchair rolls onto the platform using it spring-loaded ramp system, and he or she is able to glide (move horizontally forward and backward) by holding onto handles on each side of the plat form and pushing or pulling. If the user does not have use of his or her ar
Wheelchair Gloves (Model 70628)
Wheelchair Gloves, model 70628, are push gloves made of leather. The gloves cover the palm and back of the hands leaving fingers exposed. The leather attaches around the hand with Velcro closures. Sold in pairs.
Wheelchair Gloves (Model Wc100)
The Wheelchair Gloves, model WC100, by Hatch are push gloves designed for manual wheelchair users. The gloves have no fingers; they are cut to cover the hand up to just below the finger joints. A half sleeve covers the thumb, and the wrists are fully covered with a wide cuff. The gloves open completely at the wrist with velcro closures allowing them to be easily slipped on and off.
Wheelchair Handrim Pushing Aid
DO IT YOURSELF ENTRYPURPOSE: To enable a wheelchair user with a weak grasp to more easily propel a wheelchair. Tie three exercise bands together, end-to-end. Wrap the extended band around the handrim on one wheel of the wheelchair and tie the ends together. Repeat for the other wheel. MATERIALS: Six exercise bands. TITLE: Ten Dollar Tech. JOURNAL: TechTalk. REF: Summer 2007: p. 7. PAGES: 1.
Wheelchair Heater
DO IT YOURSELF PURPOSE: To provide warmth for a powered wheelchair user. A small blower-style heater can be purchased from the the automotive department of local discount or automotive supply stores.The heater is generally used to provide supplemental heat or to defrost windows in cars. The model chosen has a fuse rated at 15 amps to allow it to be run using a 12-volt converter on a powered wheelchair. This heater uses a squirrel-cage blower that draws air in the bottom and expels warmed air o
Wheelchair Heel Loops (Model 7018)
The Wheelchair Heel Loops, model 7018, are designed to prevent the feet of wheelchair users from slipping off of the footplates. The loops are made of strong poly webbing. DIMENSIONS: 2 inches high. COLOR: Black.
Wheelchair Heel Loops (Models 10A & 10B)
Wheelchair Heel Loops (models 10A and 10B) are designed to facilitate foot positioning and to prevent the feet from slipping off the foot rests. The devices are easy to clean and stain resistant. Model 10A ($8) is made of polyethylene, a semi-rigid plastic. Model 10AV ($8) is made of extruded vinyl which retains its shape and does not freeze or become dysfunctional when dirty. Model 10AV.1 ($26) is made of extruded vinyl with 1-inch wide cushioned ankle straps, adjustment via hook and loop faste
Wheelchair Hubs
Heavy duty, wheelchair hubs, spoke circle diameter 48mm, standard 36 hole or other spoke drillings. Standard 7/16-inch axle available in 2 lengths, 55 or 40mm. Half inch axle in 40mm length. Built for 14 gauge light spokes, larger drilling available for heavier spokes. Weight, 8.5 ounces. Precision ball bearings, permanently adjusted and lubricated, waterproof.
Wheelchair Leg Pad (Model 703070)
The Wheelchair Leg Pad, model 703070, is a legrest panel designed to prevent the user's legs from sliding off the footrests. These one-piece rigid-backed, vinyl-covered pads fit the entire width of the opening between the chair's legrests, preventing leg contact with metal wheelchair parts and providing comfort and cushioning when legrests are raised. These pads are designed for spray and wipe cleaning.
Wheelchair Leg Panel (Model 6350)
The Wheelchair Leg Panel, model 6350, is a legrest panel designed to prevent the user's feet from sliding off the foot plates. This machine-washable synthetic fur panel attaches to most chairs with buckles.
Wheelchair Leveling Pad (Models 757010 & 757015)
The Wheelchair Leveling Pad is a solid seat insert designed for use in wheelchairs. This solid, closed-cell foam pad makes wheelchair sling seats flat and level with the seat frame. This pad can be used as a foundation for other cushions. Model 757010 does not have a cover and model 757015 includes a vinyl cover. DIMENSIONS: Both models are 16 x 18 inches.
Wheelchair Liberator Push Handles
Wheelchair Liberator is designed for individuals with limited mobility and use a wheelchair for mobility. It has been designed for everyday use by wheelchair users and their caregivers to make getting around easier, more convenient and more comfortable for both the user in the chair and those pushing. It was designed to make navigating various terrains such as curbs, steps, cobbles and gravel manageable. The Wheelchair Liberator comprises of two ergonomically designed handles that quickly and ea
Wheelchair Lifter.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Wheelchair lifter permits servicing of wheelchair wheels, tires, bearings and belts without requiring the occupant to get out of the chair. Describes a lifter which can lift one side of a wheelchair about an inch off the ground. Includes drawing. COMMENTS: For information contact: Jim Anderson, Palo Alto Veterans Administration Medical Center, Rehabilitation Research Development Center, 3801 Miranda Avenue, Palo Alto, California 94304. AUTHOR: Gugerty,
Wheelchair Lunch Pail
DO IT YOURSELF PURPOSE: To provide powered wheelchair users with the ability to carry food. A standard small soft-sided cooler or insulated square lunch carrier can be secured in the empty space below the wheelchair seat behind the user's legs. A belt or other similar strap is used to secure the bag to the front wheelchair cross member. MATERIALS: Soft-sided lunch carrier or small cooler and belt or strap. SKILLS REQUIRED: Assembly. TITLE: Lunch Pail. REF: http://www.wheelchairmodifications.o
Wheelchair Navigation Sensor Shirt
---- PROTOTYPE --------- PURPOSE: To create a prototype of an adaptive, sensor-laden garment to assist people with severely limited mobility control assistive devices. Developed at the University of Pisa, a sensor-laden garment is printed with 52 flexible piezoresistive sensors. The sensors are made of electroactive polymers that change voltage depending on the angle at which they are stretched. A specialized statistical algorithm analyzes the signals record from each sensor to detect the speci
Wheelchair Pack
The Wheelchair Pack is a wheelchair back pouch designed for use by individuals who use wheelchairs. This waterproof pack features large privacy compartments with zippered closure and deep side pockets for holding beverages, newspapers, or magazines. Other features include buckled straps that fasten over the seat loop handles that slip over wheelchair canes. A carrying handle is also included for use as a portable tote. DIMENSION (HxLxW): 5 x 15 x 15 inches. COLOR: Black.
Wheelchair Pack (Model Ez0200)
The Wheelchair Pack is a wheelchair back pouch designed for use by individuals with mobility disabilities or spinal cord injury. Made of weather-resistant nylon, this pack attaches to the back of wheelchair seat using buckled straps that fasten over the seat back and loop handles that slip over the wheelchair handgrips. The Wheelchair Pack has a large interior compartment with zippered closure and deep side pockets as well as a carrying handle for use as a portable tote. DIMENSIONS (HxLxW): 5 x
Wheelchair Pack Carryon
The Wheelchair Pack Carryon is designed for use by wheelchair users with mobility or lower extremity disabilities or spinal cord injury. The zippered pack allows users to transport books or other items on their wheelchair. It features expandable side pocket for holding beverages, straps with adjustable buckles that securely attaches the pack to the back of the chair, and an outside mesh pocket to hold magazines and newspapers.
Wheelchair Positioner Cushion
The Wheelchair Positioner Cushion is a torso support designed for use by individuals who use wheelchairs. This M-shaped cushion rests over th lap of the users and the notches fit around the wheelchair frame to keep the cushion in position. Designed for use in wheelchairs with standard arms, this cushion promotes upper body alignment, prevents forward leaning, and serves as an elbow rest and work surface. A removable, wipe-clean, water-repellant vinyl cover is included. DIMENSIONS: Available in a
Wheelchair Push Gloves (Model 16C017A)
The Wheelchair Push Gloves, model 16C017A, are push gloves designed for use by individuals with lower extremity or mobility disabilities, spinal cord injury, and others who use manual wheelchairs. Made with suede palms and mesh backs, these bicycle-style push gloves are designed to help protect the hands from blisters and injury while propelling a wheelchair. The open mesh back allows for ventilation while the padded palm area is durable and has a no slip grip. The gloves have open fingers, a ha
Wheelchair Push Handle Extensions For Tall Person
CUSTOM ADAPTATION PURPOSE: To enable a tall caregiver to safely push a wheelchair. Designed to work with a variety of wheelchairs and to be removable for use on multiple chairs, a set of tubular steel extension arms with handgrips at the top was fashioned. The extensions are adjustable and hook to the chair frame at the bottom. The height of the handles can be adjusted using wing nuts on the verical uprights and the width between the handlebars is adjustable using a wing nut on the horizontal b
Wheelchair Reading Board.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Wheelchair tray with a hinged section that tilts up to support reading material; can be swung out of the way or easily removed. Lists materials needed and provides drawing and diagram for a wheelchair reading tray, made of wood with aluminum bar stock and pipe tube. COMMENTS: For information contact: Dr Ken Bruwelheide, Department of Agricultural and Industrial Education, Montana State University, Bozeman, Montana 59717. SKILLS REQUIRED: Woodworking. M
Wheelchair Safety Alarm
The Wheelchair Safety Alarm is designed to help caregivers keep track of the disabled love one. It sounds an alert as soon as the individual lifts themselves out of their wheelchair. Covered in waterproof vinyl. Can be used by other chairs as well. The pressure pad connects to the audio alarm. The alarm has an On/Off switch and battery warning.
Wheelchair Safety Belt
The Wheelchair Safety Belt is a wheelchair seatbelt designed to prevent falls from wheelchairs. The adjustable, heavy-duty Velcro belt crosses the lap and attaches to the wheelchair axle with reinforced grommeted nylon straps. SIZES: One size fits most.
Wheelchair Seat Mount for Xbox Adaptive Controller
The Wheelchair Seat Mount for Xbox Adaptive Controller is a mountable arm that attaches to wheelchairs, rails, bars, and flat surfaces to enable use of the Microsoft Xbox Adaptive controller for people with mobility, fine motor, or upper extremity disabilities. The controller attaches directly to the included RAM® diamond base adapter with 1.5-inch ball and double socket swivel arm, allowing for a 90-degree tilt so users can angle the adaptive controller exactly where needed. When the Xbox Adapt
Wheelchair Seatbelt (Models 6880 & 6886)
The Wheelchair Seatbelt is a belt restraint designed to keep individuals in wheelchairs from falling forward out of the chair. It can be permanently attached to the upholstery screws and has a Velcro closure. DIMENSIONS: Both models are 2 inches wide; Small (6880) is 32 to 42 inches long, Large (6886) is 42 to 52 inches long.
Wheelchair Seatbelt Sleeve
---- “DO IT YOURSELF” ENTRY --------- PURPOSE: To create a “sleeve” to fit over a child’s wheelchair seatbelt, making the belt safer and harder to undo. First, lay material on flat surface with back side facing up; using straight pins, pin edges together lengthwise along material. Second, using a sewing machine or needle; stitch along line lengthwise. Third, turn material right side out and slip onto one end of wheelchair seatbelt. Fourth, fasten the belt and slide material over fastener; scrun
Wheelchair Shopping Box
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual who uses a powered wheelchair to shop independently. A sheet steel box with its base above the client's knees was created. The box is high enough to accommodate a box of powdered detergent. The front of the box is lozenge shaped to match the plan view of wheelchair foot supports, and the lid is hinged at the back The high rim around the lid is 1/16 inch thick plastic, and there are gaps between it and the lid so that rain will not collect
Wheelchair Side Pac (Model Wh155)
The Wheelchair Side Pac, model WH155, is a carrying bag for wheelchairs made of waterproof nylon. The bag attaches to the inside of the wheelchair arm for greater security. Other features include a large main pocket, smaller pockets for wallets, checkbooks, pens, etc. and a lid zipper pocket with a large zipper pullring and pull tabs. DIMENSIONS: 10.5 x 6.5 x 2 inches.
Wheelchair Side Pouch
The Wheelchair Side Pouch is designed to provide carrying capacity for individuals. This pouch fits all wheelchairs with standard arms and it can be used on the inside or outside of the cahir. Made of self-lined vinyl, this pouch features a top zippered pocket and divided pockets on either side. DIMENSIONS: 6.5 x 12 inches. COLOR: Black.
Wheelchair Side Tote (Model Pt508)
The Wheelchair Side Tote, model PT508, is a carrying bag designed for attaching to a wheelchair for individuals with physical disabilities. This bag provides easy on/off handling and is equipped with adjustable velcro top straps. It is made from medium weight canvas. OPTIONS: Silk screening with a logo or message is available in a variety of colors. DIMENSIONS: 6.5 x 14 inches. COLORS: Body colors are natural, red, navy, royal, green and black. Assorted webbing and trim colors are available.
Wheelchair Single Leg Strap (Model 7016)
The Wheelchair Single Leg Strap, model 7016, is a legrest strap designed to prevent the legs of wheelchair users from slipping behind the footplates. The strap is made of strong poly webbing with a Velcro closure. SIZE: Fits standard adult or narrow adult wheelchairs. COLORS: Black.
Wheelchair Single Oxygen (Models Ez0140 & Ez0141)
The Wheelchair Single Oxygen is an oxygen cylinder carrying case for a manual wheelchair designed for use by individuals with respiratory disabilities and mobility disabilities or spinal cord injury. Made of water-resistant 420-denier nylon, the case holds one or two "D" and "E" cylinders. An adjustable snap allows the carrier to be fitted to the size of the cylinder. An adjustable extra-long top strap with buckle attachment secures the case to most manual wheelchair seats, and it can be positio
Wheelchair Slipcover (Model 6393)
The Wheelchair Slipcover, model 6393, is a seat cover for a wheelchair designed to enhance comfort and reduce pressure sores. This one-piece plush synthetic fur pad covers the wheelchair seat and back. DIMENSIONS: This pad fits most 16-, 18-, and 20-inch wheelchairs.
Wheelchair Slippers (Models 6480S-M & 6480M-L
Wheelchair Slippers are foot protectors designed for use by individuals who use wheelchairs. Each of these soft plush, machine-washable slippers feature a strap on the bottom that slides over the wheelchair footplate, securing the slipper to the footplate, protecting the foot and providing a surface for the wearer to push against to stop forward sliding. SIZES: Model 6480S-M fits women's shoe sizes 5 to 10 and men's shoe sizes 5 to 8. Model 6480M-L fits women's shoe sizes 10 and up and men's sh
Wheelchair Snack Tray (Model 70621-0000)
The Wheelchair Snack Tray, model 70621-0000, is a lapboard designed to clamp to wheelchair tubing to hold snacks and beverages. The tray sticks to a platform by Velcro pads to facilitate removal for cleaning. The try is made of polystyrene; metal parts are epoxy coated. DIMENSIONS: 6.5 x 9.75 inches.
Wheelchair Sweeper Hitch
DO IT YOURSELF ENTRYPURPOSE: To enable individuals who use scooters or wheelchairs to operate a commercial powered sweeper. This accommodation required design and development of a custom hitch system with a pin release linkage to which the battery-powered sweeper could be attached, enabling the scooter user to perform the job of vacuuming the halls at his place of employment It was also necessary to upgrade the scooter/wheelchair batteries to accommodate the increased load. This project used sta
Wheelchair Table Attachment
This Wheelchair Table Attachment is a wheelchair lapboard with removeable desk arms. The table attaches to the wheelchair frame and front of the armrests with clamps. The tray is made of wood with a formica top and aluminum tubing. DIMENSIONS: 8 w x 24 l Specify width between arm rests when ordering.
Wheelchair Tablet Holder for iPad Mini
Wheelchair Tablet Holder for iPad Mini or 7 inch Tablets is a wheelchair accessory designed or users in wheelchairs to be able to mount an IPad Mini or other 7 inch tablets onto their wheelchair.
Wheelchair Tablet Holder for Tablets
Wheelchair Tablet Holder is a wheelchair accessory designed for use by those in wheelchairs to mount on their chair and fit Apple iPads & Most standard 10 inch Tablets. The universal tablet holder has a spring loaded cradle that expands and contracts for a perfect fit of most tablets. It has rubber coated tips that will hold your tablet firm and stable. The versatility of the cradle allows for attachment to many 1 inch socket mounts. It has easy access grip knobs located on the back of the c
Wheelchair Totebag
---- DO IT YOURSELF ENTRY --------- PURPOSE: To create a do-it-yourself tote bag for use on a wheelchair for individuals with mobility disabilities. While sitting in a wheelchair accessing pant pockets for storage of everyday items (i.e. diary, cordless phone, etc.) is difficult and not convenient. This convenient wheelchair tote bag is created from good quality canvas or corduroy material. About of a meter should be enough to do the job. Velcro is also needed to fit across the width of the sack
Wheelchair Tray
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted tray to fit on a wheelchair used by an individual with cerebral palsy and intellectual disability. This individual spends most of her day in her wheelchair and needs something to occupy her and a surface to rest it on; in other words, a portable table which she can use for her walkman, DVD player or to hold a magazine, etc. The tray is made from 9 millimeter plywood with a lip added around the front and side edges to stop o
Wheelchair Tray
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual who uses a wheelchair to carry meals and items and to have a drink holder. This tray is customized to fit the individual wheelchair. Made of wood and varnished, the tray has a wooden rim on all sides to keep items from rolling or sliding off. Wooden or metal rods fastened to the bottom of the tray slide into the hollow horizontal tubes under each armrest. To allow the rods to be inserted, the front retaining screw on each armrest must be
Wheelchair Tray
The Wheelchair Tray is a lapboard designed for use by individuals who use wheelchairs. This plastic tray helps provide support for proper positioning while creating work and eating space. The tray features a torso cutout and raised edges prevent items from rolling. Velcro fasteners securely fasten the tray to the wheelchair. DIMENSIONS: 20 x 24 inches. WEIGHT: 1.1 pounds.
Wheelchair Tray
The Wheelchair Tray is a lapboard designed to enable the user to eat or do other activities from their wheelchair and to provide some protection from spills. The tray is made of plywood with two sides that rest on the seatpan of the wheelchair. A vinyl seal is fixed to the inside edge of the tray to protect the user from spills. PROTOTYPE DEVELOPMENT: Designed by John Duffus as a more comfortable and practical eating surface for wheelchair users at a standard height tabletop that is not high eno
Wheelchair Tray (Model 5061) & Wheelchair Tray Child Size (Model 2467)
Wheelchair tray with rim fits all size wheelchairs with full length or desk arms. Sides are tapered to permit chair propulsion with tray in position. Smooth plastic top. 24 by 19 inches with 15 by 6 inch cutout; child size 20 by 19 inches with 12 by 3 1/2 inch cutout.
Wheelchair Tray (Model 6025)
Formica lapboard, Velcro fasteners. Adult size, 24 by 20 inches by 1 inch.
Wheelchair Tray (Model 91)
The Wheelchair Tray, Model 91, is a solid lapboard that fits on the armrests of a wheelchair. The tray has a stain-resistant liminated finish ans Velcro attachment straps.
Wheelchair Tray (Model H70601-0015)
The Wheelchair Tray, model H70601-0015, is a formica lapboard designed to be attached to either side of a wheelchair with Velcro fastening straps. This rigid tray has a non-glare surface, a cutout, and a channel around its perimeter to catch spills. The edges are protected by smooth plastic molding. DIMENSIONS: Tray is 24 x 19 inches. WEIGHT: Shipping weight is 8.3 pounds.
Wheelchair Tray Easel (Models 31140 & 31141)
The Wheelchair Tray Easel, Models 31140 and 31141, is a bookholder with lapboard and an easel designed for use by people who use wheelchairs. The adjustable angle easel attaches to any lapboard with a front rim. Model 31140 is made of clear polycarbonate, and Model 31141 is fabricated of Melamine-impregnated fiberboard. Both models have a hinged, adjustable length leg brace for setting the angle of the easel. The easel includes a 1.5-inch front edge or lip. WARRANTY: The manufacturer warrants th
Wheelchair Tray.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Provides an attached table surface for a person in a wheelchair; can be used for activities or for arm support. Materials, diagrams and directions for making three types of wooden wheelchair laptrays. A standard tray with Velcro straps for attachment to wheelchair arms; a variation which folds in half; and a lowered tray useful for activities like cooking. SKILLS REQUIRED: Woodworking. AUTHOR: Gavee, B. TITLE: Wheelchair and Accessories REF: Book: Acce
Wheelchair Trays
The Wheelchair Trays are lap trays designed for use by children and adults who use wheelchairs. Made of shatterproof clear polycarbonate, the trays include adjustable mounting hardware. OPTIONS: Engraving of names and addresses, custom cutouts, slantboards, and more. DIMENSIONS: All models are made of 3/8-inch thick polycarbonate. Standard models are available for 10- to 12-inch wheelchairs, 13- to 14-inch chairs, 15- to 17-inch chairs, and 18- to 20-inch chairs. Custom dimensions are also avail
Wheelchair Trays (Models 4040, 4042, 4044, 4080, & 4090)
The Wheelchair Tray, models 4040, 4042, 4044, 4080, 4090, is a lapboard designed to be used by individuals in wheelchairs who need a hard, flat surface for eating, writing, etc. The trays have raised T-molding on the outside edges for extra security and have a half-moon cutout facing the individual. The universal design fits all standard wheelchairs and attaches with Velcro fasteners. SIZES: Adult 20 x 24 x 1/2 1 inch. Child 20 x 18 x 1/2 inch.
Wheelchair Trays And Modifications
Lapboards. Available in 1/2 inch 9 ply birch plywood, or 3/8 or 1/4 inch Tuffak (polycarbonate material), with regular or heavy duty cottonwood ribs. Range of widths, 20 7/8 to 25 3/4 inches; depths 17 7/ 8 to 25 3/4 inches; Cam adjustment range 13 3/4 - 18 1/4 inches to 18 1/ 4 - 23 1/4 inches. Small fits STC 803/900 Models and Tiny Tot and Growing wheelchairs; Medium fits STC 804/806/900 Models and Growing, Narrow Adult and Adult wheelchairs; Large fits STC 804/806/900 Models and Adult wheelch
Wheelchair Umbrella
The Wheelchair Umbrella is designed to provide shelter from the elements for wheelchair users. The umbrella is made of a vinyl tent mounted on a frame which folds down behind the chair. Clear plastic windows provide visibility when the tent is up. The unit mounts to the wheelchair frame in four locations. PROTOTYPE DEVELOPMENT: Designed by Dave Doman for wheelchair users to allow them to quickly employ a cover in the event of rain without worrying about getting raingear caught in the wheels of
Wheelchair Underneath Carrier (Model Ez0160)
The Wheelchair Underneath Carrier is a wheelchair under seat carrier designed for use by individuals with mobility disabilities or spinal cord injury. Made of weatherproof, stain- and mildew-resistant mesh, the carrier has front and back flaps the keep items from sliding out on inclines. It hangs from the frame of the wheelchair directly beneath the seat using Velcro attachment straps. DIMENSIONS (HxLxW): 2 x 17 x 15 inches. COLOR: Black.
Wheelchair Underneath Carryon
The Wheelchair Underneath Carryon is an under seat pocket designed for use by individuals who use wheelchair. The unit attaches underneath the wheelchair to hold books, packages, and other small items. This large waterproof mesh carrier has a hanging design with Velcro attachment that features front and back stop flaps to keep items secure. The device is stain- and mildew- resistant. DIMENSIONS (HxLxW): 2 x 15 x 17. COLOR: Black
Wheelchair Waist Belt With Buckle
The Wheelchair Waist Belt With Buckle, model MDT825120, is a wheelchair seatbelt designed for use by individuals with mobility disabilities or spinal cord injury. Made of washable nylon, this latex-free belt circles the waist, passes through a slide buckle, and ties in back. The slide buckle allows for individual fit and prevents overtightening. SIZES: One size fits all.
Wheelchair Y Safety Belt (Model 6038)
The Wheelchair Y Safety Belt is a belt restraint or wheelchair seatbelt. The "Y" shape is designed to prevent slumping and sliding of individuals in wheelchairs. The belt is completely adjustable and made of nylon webbing. SIZES: One size fits all.
Wheelchiar Bag
The Wheelchair Bag by Karma is designed for individuals with limited lower extremity mobility disabilities. This wheelchair bag is ideal for travelling. It folds into a small package for storage and it has wheels for easy to manage pulling around.
Wheeleez Balloon Wheels
Wheeleez Balloon Wheels are beach wheelchair wheels designed for use by individuals with mobility disabilities, lower extremity disabilities, and spinal cord injury. These wheels have flanged hubs and polyurethane balloon tires that are pliable enough to roll over soft sand, muddy turf, snow, sensitive environments, and uneven surfaces, including bumps, stairs, and curbs. The wheels are made from PVC or polyurethane depending on size. OPTIONS: Swivel or rigid caster for the 11.8-inch wheel. DIME
Wheelers' Paramill
The Wheelers’ Paramill offers wheelchair users the ability to achieve their fitness goals while using their own chair. Users can and keep their cardiovascular system healthy while using resistance and avoid repetitive motion injuries with a reverse motion function. The Paramill can also be used in clinical settings to help with rehabilitation in correcting stroke pattern and assist in the chair fitting process. Also use the power of resistance and reverse motion to help strengthen core muscles w
Wheelie
The Wheelie is a kit that allows people with mobility disabilities to drive a wheelchair using facial expressions which can be installed in seven minutes. The device recognizes facial expressions captured by a special digital camera and converts them into commands to move a motorized wheelchair. Users choose five of the nine available facial expressions to control the motorized wheelchair. The Wheelie features real-time facial analysis.
WheelMate
WheelMate™ is an interactive functional application for those individuals who use wheelchairs to navigate independently. Highlights wheelchair accessible features around users. In particular, this app assists individuals to locate accessible parking and bathrooms when they are on the move.
Wheelnest Seating System
The WheelNest Seating System is a portable system for prolonged, balanced seating in wheelchairs, cars, office or other chairs that has a molded seat, solid seat and solid back inserts, and gel flotation seat cushion. WheelNest provides a balanced underseating as well as lumbar back support; helps maintain proper lordosis (curvature of the spine), correct hip position and proper spine alignment; and helps prevent decubitus ulcers. BACK SUPPORT: The back support is made of padded, contoured layer
Wheels!
Wheels! is a video game designed for use by children with cognitive, sensory, or motor disabilities. This game can be played as a game or it can be used to teach wheelchair control skills. This three-dimensional video game has players fight evil clowns and mad robots with pie guns that "cream" the monsters with lemon meringue pies; the monsters fight back with pie guns that fire blueberry pies. The game uses easy-to-follow mazes set in a familiar school setting with familiar objects. Each maze o
Width Varying Device For Wheelchairs.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Narrowing wheelchairs for doorway access. The device can be mounted on any size wheelchair with a folding crossbrace. Does not interfere with folding the chair. Can be installed for right or left hand use. Only two fingers needed to activate switch. A geared low speed motor is mounted on one side of the chair frame. A strap is attached to the opposite side of the frame and to the motor pulley. Pressing the switch operates the pulley to pull the sides o
Wijit
The Wijit is a wheelchair lever drive and braking system designed for use by individuals with mobility disabilities. The system includes a lever that attaches to each drive wheel of most manual wheelchairs, enabling the user to propel the chair using a pumping motion. The levers can be switched to reverse mode to enable the user to reverse directions. To engage the braking system to reduce speed or stop, the levers are simply pushed forward toward the body.
Wing Self-Storing Wheelchair Tray
The Wing Self-Storing Wheelchair Tray is a swing-away lapboard for manual and powered wheelchairs and 3-wheeled scooters. The patented, tablet-size tray is made of clear polycarbonate plastic, and has a pencil/spill trough plus a rim along the outer edge and a slide control. When the tray is in the stored position, the user has unobstructed access to the wheels of the chair. An adjustable, 3-directional hinge and a telescoping arm permit the tray to flip up or down and slide back and forth. Moun
Wood Tray With Vinyl Cover
The Wood Tray with Vinyl Cover is a wheelchair lap trays designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. The tray is made of birch wood with a wooden rim, and it has foam padding with a vinyl cover. The unit comes with mounting hardware, and it is available as a stationary or flip-up tray for the right or left side of the wheelchair. DIMENSIONS: 22 x 13 inches; wood is 0.38 inches thick; foam is 1 inch thick.
Woodline Light Trays (Series 31100)
The Woodline Light Trays are lap trays designed for use with wheelchairs. These seven-ply birch trays have limitied moisture resistance and can be attached using the E-Z Lock Clamp, Top Drop Clamp, Tube Arm Braxkets (not included), or other attaching system. Models include the tray only, tray with hook-and-loop attaching straps, tray with a three-piece wood rim, and tray with straps and rim. SIZES: Child (fits wheelchairs 12 to 14 inches wide), adult (fits chairs 14 to 17 inches wide), extra wid
Woodline Series
The Woodline Series are lapboards designed for use by people who use wheelchairs. The trays are constructed of 7-ply birch plywood with a lacquer finish. Models include the tray only, tray with 3-piece wood rim, tray with straps, and tray with straps and rim. The juvenile tray has an oblong design, while the other models are square. SIZE: All models are available in child, juvenile, adult, and X-wide sizes. DIMENSIONS (W x D): The adult tray is 23.5 x 22 inches, with a 15 x 9 inches torso cutout
Wunderglow Wheelchair Light System Kit
The wUnderglow Wheelchair Light System Kit is a wheelchair light set designed for use by individuals who use wheelchairs. The set includes two micro lights and a mounting clip. The white light increases visibility and the multi-colored light can be used to increase visibility or strobing for visibility and effect. The clip rotates 360 degrees to enable the user to select precise positioning. POWER: Uses two replaceable CR 2016 lithium batteries in each light. OPTIONS: Second clip to enable both
X-Core 3
X-Core Wheels are rear wheelchair wheels designed to replace the existing wheels on the chair. Made of carbon fiber composites, these lightweight wheels have three brodly-spaced spokes and welded hard anodized aluminum handrims. The maximum tire pressure for these wheels is 100 pounds per square inch. These wheels accept 25-inch wheelchair tires or 26-inch mountain bike tires. DIMENSIONS: These wheels fit .5-inch axles and are 25 x 1 inches in diameter.
X-Core 5-Spoke
The X-CORE 5-Spoke is a rear wheelchair wheel designed to replace the existing wheels. These wheels are hollow, seamless, lost-core composite
with smooth sealed bearings. They combine the rim, spokes and hub into one composite unit. The wheels do not include tires but come standard with a hard anodized aluminum handrim and a choice of bearing sizes. OPTIONS: Plastic-coated or foam-coated handrims, Primo HP Gray tires, and Alshin Tire polyurethane no-flat tires with herringbone tread are availabl
X-Core 6
The X-CORE 6 is a rear wheelchair wheel designed to replace existing wheels on wheelchairs. These six-spoked wheels are hollow, seamless, lost-core composite wheels with smooth sealed bearings. They come standard with hard anodized aluminum handrims, Alshin polyurethane pyramid tires, and a choice of bearing sizes. OPTIONS: Plastic-coated or foam-coated handrims and Alshin polyurethane herringbone tread, rounded profile tires are available at extra cost. DIMENSIONS: The wheels are 24 x 1 inch. T
X-Fer Rail Portable Transfer Rail
The X-Fer Rail Portable Transfer Rail is a transfer board for designed for caregivers to use with individuals with mobility difficulties. Enables safe transfers to and from a wheelchair. Quickly folds and unfolds. Conveniently fits in a backpack, wheelchair bag, carry-on or briefcase (not included). Portability of the board promotes use outside of the home which will help to reduce shoulder strain associated with independent transfers. Open seating design reduces the risk of friction based skin
Y-360 Series Wheel
The Y-360 Series Wheel is a manual wheelchair wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Made of billet aluminum, this is a mod style wheel with inserts. The spokes have a polished aluminum finish and the handrim is anodized. The wheel is sized for a 0.5-inch axle and has a maximum camber of 2 degrees. The wheel comes with Primo tires and a choice of three different inserts: Eagle Eye, Cherry Girl, or Tribal Sun. OPTIONS: Vinyl-coa
Zero Shear Manual Recliner
Zero shear manual recliner for Everest & Jennings recliner wheelchair frames 47 or 49. High quad seating system replaces standard seat. Reclining frame, sliding back, rigid seat, standard headrest. Back height 19 to 25 inches in one inch increments. Reclines to 180 degrees. Options: spinal or scapular cutout back, reclining arms, arm troughs, leg troughs, lateral supports, vent tray. Custom orders available.
Zero Shear Power Recliner
Zero shear power recliner for Invacare Arrow recliner frame and sectional back chairs, or Everest & Jennings recliner frames 47 or 49, and standard Marathon sectional back wheelchairs. High quad seating system replaces standard seat assembly. Reclining frame, sliding back, rigid seat, standard headrest, quick release reclining arm hardware, arm and leg troughs, underseat module mount standard. Toggle switch control. Back height 19 to 25 inches in one inch increments. Underseat 24 volt DC act
Zeus Sealed Lead Acid Battery (Model Pc33-12)
The Zeus Sealed Lead Acid Battery, Model PC33-12, is a sealed, maintenance-free replacement battery designed for use with powered wheelchairs and scooters. This rechargeable 12-volt battery has capacity of 33 ampere hours. The manufacturer states that the battery will last up to 5 years in standby applications and 200 to 1,000 cycles in cyclic applications depending on depth of discharge. DIMENSIONS (LxWxH): 7.68 x 5.16 x 6.5 inches. The height over terminal is 8.9 inches. WEIGHT: 23.79 pounds.
Zeus Sealed Lead Acid Battery (Model Pc55-12)
The Zeus Sealed Lead Acid Battery, Model PC55-12, is a sealed, maintenance-free replacement battery designed for use with wheelchairs and scooters. This rechargeable 12-volt battery has capacity of 55 ampere hours. The manufacturer states that the battery will last up to 5 years in standby applications and 200 to 1,000 cycles in cyclic applications depending on depth of discharge. DIMENSIONS (LxWxH): 9.02 x 5.43 x 8.11 inches. The height over terminal is 8.9 inches. WEIGHT: 37.44 pounds. WARRAN
Zeus Sealed Lead Acid Battery (Model Pc70-12)
The Zeus Sealed Lead Acid Battery, Model PC70-12, is a sealed, maintenance-free replacement battery designed for use with powered wheelchairs and scooters. This rechargeable 12-volt battery has capacity of 70 ampere hours. The manufacturer states that the battery will last up to 5 years in standby applications and 200 to 1,000 cycles in cyclic applications depending on depth of discharge. DIMENSIONS (LxWxH): 10.2 x 6.61 x 8.19 inches. The height over terminal is 8.9 inches. WEIGHT: 49.78 pound
Ziggy Swing Tray
Swing away lapboard for E & J wheelchairs with interchangeable full size armrests. Lapboard mounts to the front of the frame, swings down to side for storage, or, it can be mounted to be used on the side of chair. Top can be adjusted vertically. Acrylic. Specify color of armrest pad.